RCD CC1/2-470-KTW

RoHS CARBON COMPOSITION RESISTORS RESISTORSCAPACITORSCOILSDELAY LINES 1/4 WATT TO 1 WATT Term.W is Pb-free and RoHS CC SERIES compliant Mil-Spec screening and a Tin-Lead terminal finish are available as options  High surge/high pulse capability on this & most other RCD products.  Low inductance/high frequency performance  Rugged hot molded construction  1/8W & 2W models in development Carbon comp resistors are considered one of the most reliable of all electronic components. There are no windings or film, resulting OPTIONS in a non-inductive resistor with excellent pulse-withstanding capabil-  Option 37: Group A screening per MIL-R-39008 ity. Hi-Rel Group A or A&B Screening per Mil-R-39008 is available.  Option EU8: Group A&B screening per MIL-R-39008  Option ZZ: Z-formed leads for surface mounting ← H →← L → d → D ←  Custom marking/ testing/ cut&formed leads, hot solder ↓ dipped leads, preconditioning, & numerous other options. ↑ . Dimensions Inch [mm] RCD Wattage at Max Peak Pulse Joule Dielectric Resis. Range 1 2 3,5 3,4 Type 70° C Voltage Voltage Rating Strength E24 Std Values 4 4 L D d H (bulk pack) .250±.032 .090±.016 .024±.003 CC1/4 0.25W 250V 6KV 1.8j 500V 1W - 22M 1.0 [25.4] typ. [6.35±.8] [2.3±.4] [.6 ±.076] .374±.040 .140±.018 .028±.004 CC1/2 0.5W 350V 10KV 6.4j 700V 1W - 22M 1.0 [25.4] typ. [9.5±1.02] [3.56±.45] [.7 ±.1 ] .610±.05 .232±.022 .036±.006 CC1 1W 500V 14KV 20j 1000V 2W - 1.2M 1.0 [25.4] typ. [15.5±1.27] [5.90±.55] [.9 ±.15] 1 2 1/2 3 Derate W & V by 1.25%/°C above 70°C Rated continuous voltage determined by E= (PR) , E not to exceed the max value listed. Increased levels available 4 Allow .032” [0.8mm] additional to L and D on parts with optional conformal coating 5 5 5 CC1 Peak Pulse Voltage (14KV Max) CC1/4 Peak Pulse Voltage (6KV Max) CC1/2 Peak Pulse Voltage (10KV Max) 1M 10KV 10KV 10KV 1M 100K 1M 100K 100K 10K 1KV 1KV 1KV 10K 10K 1K 1K 1K 100W 100V 100V 100V 100W 100W 10W 10W 10V 10W 10V 10V 1uS 10uS 100uS 1mS 10mS 100mS 1uS 10uS 100uS 1mS 10mS 100mS 1uS 10uS 100uS 1mS 10m 100mS Pulse Width (Sec) Pulse Width (Sec) Pulse Width (Sec) 5 Peak pulse (rupture) voltage and joule ratings are dependent on resistance value, pulse wave form & repetition rate. Charts indicate the maximum peak pulse (rupture) voltage based on capacitive discharge non-inductive circuit, pulse width equates to one RC time constant. Derate >25-50% for repetitive pulses and improved stability/reliability. Repetitive pulse aver- age power not to exceed wattage rating. Verify selection by evaluating under worst case conditions. Refer to R-46 guide or consult factory for assistance. TYPICAL PERFORMANCE CHARACTERISTICS TEMPERATURE RISE Short-time Overload ±2.5% 60 Thermal Shock ±4% 50 CC1/2 CC1 Temperature Coefficient ±0.15%/°C 40 Moisture Resistance ±10% 30 CC1/4 Shock and Vibration ±2% Load Life MIL-R-39008 3.21.1.2 ±10% 20 Terminal Strength (direct pull) 5 lbs. min. 10 Operating Temp. Range -55° C to + 130° C 0 Standard Marking 4 color bands typ. (or alpha 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Color Code Table numeric, 5th FR band) APPLIED WATTAGE (W) APPLICATION P/N DESIGNATION: CC1/2 - 101 - J T W Ideal for snubber circuits, lightning surges, grounding resistors, RFI sup- RCD Type pression, dummy loads, etc. Depending on the application, CC’s can often Options: 37, EU8, etc (leave blank if std) satisfy requirements of GR1089, ITU-K20, IEC61000-4-x, FCC Part 68, etc. 3-Digit Resis Code: 2 signif. digits & multiplier Composition construction isn’t as stable as other types of resistors especially (1R0=1W, 100=10W, 101=100W, 102=1K, 103=10K, etc) in humid conditions, and therefore not suitable for precision applications Tol Code: J=5% (std on CC1/4 &1/2), K=10% (std CC1), (refer to RCD’s PR Series for improved environmental performance). As per consult factory for 2% (G) tolerance MIL-R-39008, parts that have shifted beyond the nominal tolerance due to Packaging: B= Bulk, A= Ammo Pack, T= Tape & Reel moisture may be baked at 100°C to recondition the parts back into tolerance. Forming: ZZ=surface mount (leave blank if std), additional options avail Tape & Reel: standard qty/reel= 5Kpcs CC1/4, 4K or 5K CC1/2, 1K CC1 Termination: W=Lead-free (std), Q=Tin/Lead (leave blank if both acceptable) (non-std qty & cut reels available) - - - - RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603 669 0054 Fax: 603 669 5455 Email:sales@rcdcomponents.com FA001 K Sale of this product is in accordance with GF-061. Specifications subject to change without notice. 74 RCD Peak Voltage Peak Voltage TEMP RISE (°C) Peak Voltage