RCD MGP50-3402-BT10

RoHS RESISTORS�CAPACITORS�COILS�DELAY LINES METAL FILM MELF RESISTORS Term.W is RoHS MGP SERIES - Conformal Coated compliant & 260°C compatible MHM SERIES - Hermetic Sealed Metal film performance, economical price! � Industry’s widest selection of metal film MELF resistors- RCD Series MGP melf* resistors utilize precision film technology .1W to .5W, 0.1Ω to 22MΩ, 0.1% to 5%, 10ppm to 100ppm/°C TM which is inherently low inductance, low noise, and high stability � Low cost, quick delivery (available on SWIFT program) � Precision performance, excellent environmental stability even after extended periods. Heavy solder plating assures � Series MHM hermetic sealed is an industry first! excellent solderability and long shelf life. Series MHM offers hermetically sealed environmental protection and utmost OPTIONS reliability. MGP series parts are color banded, MHM are alphanu- � Option S: Increased power (refer to chart below) merically marked with resistance and tolerance. *Melf = metal � Option P: Increased pulse capability electrode face-bonded (cylindrical component). � Option F: Flameproof coating (per UL94V0) � Dozens of additional options are available... burn-in, special L marking, non-standard values, high frequency designs, W D matched sets, temp. sensitive, zero-ohm jumpers, etc. Customized components are an RCD specialty! Inch [mm] t SPECIFICATIONS RCD We attag Wattage Voltage Resistance Dielectric 2 L] ±.012 [.3]D) ±.008 [.2 W (Min. t (Max) 2 1, 2 2 Type (Std) (Opt. 'S') Rating Range Strength MW GP45.W 1 .V 15 11 00 ΩtV o 1M2] 00.] 079 [2.0.] 044 [1.12.] 012 [.3 .003 [.076 MW GP50.W 125 .V 25 28 00 0.1 ΩtV o 10M2] 50.] 135 [3.4.] 057 [1.45.] 02 [.5 .004 [.1 MW GP55.W 25 .V 5 21 50 0. ΩtV o 22M3] 50.] 232 [5.9.] 085 [2.15.] 024 [.6 .006 [.15 3 MHM55.W 125W.V 25 20 50 1 ΩtV o 200K3] 50.] 275 [7.0.] 120 [3.05.] 050 [1.27 .006 [.15 1 Max working voltage determined E= √(PxR), not to exceed the value listed. 2 Consult factory for non-standard range 3 Preliminary PERFORMANCE PULSE WITHSTAND CHART (increased pulse levels avail.) M* GP Series* MHM Series 1000 100ppm/°C std, 100ppm/°C std, TCR (10 & 15ppm avail on custom basis) 25&50ppm avail 25&50ppm avail OC perating Temperature Range-C 55 to +155° -65 to +175° 100 PC ower Derating above 70°C 1C .18%/° .95%/° Se olderability (5 sec @ 230°C)9e 5% coverag 95% coverag IM nsulation Resistance(Dry) 10,000 Ω 10,000MΩ 10 MGP55SP Short-Time Overload (5 sec. @ 2.5x 0.25% .025% MGP50SP power not to exceed 2x voltage rating) (0.5% Opt.S) (.05% Opt.S) MGP45SP R% esis. to Solder Heat (260°C, 5 sec.)0% .2 .02 1 T% emperature Cycling (-50°C + 120°C)0% .5 .02 1uS 10uS 100uS 1mS 10mS 100mS Pulse Duration Mi oisture (MlR -Std202 M106 & Mil--55342)0* .5%** .05%* Pulse capability is dependent on res. value, waveform, repetition rate, L) oad Life (1000 hours rated power)0) .5%(1%Opt.S .1% (.2% Opt.S current, etc. Chart is a general guide for Opt. P pulse resistant version, single pulse, with peak voltage levels not exceeding 1KV for MGP55SP, * Typical performance levels listed are for standard products from 10Ω to 1M. 700V MGP50SP, and 350V MGP45SP. Max pulse capability for standard Consult factory for performance levels of extended range and modified designs. ** To ensure utmost reliability, care should be taken to avoid potential sources of parts (w/o Opt.P) is 60% less. For improved performance and reliability, ionic contamination a 30-50% pulse derating factor is recommended (or larger for frequent pulses, high values, etc). Consult RCD for application assistance. Verify selection by evaluating under worst-case conditions. APPLICATION NOTE #1: Temperature Rise (T ) HS The T of SM resistors depends largely on heat conduction through the HS end terminations, which can vary significantly depending on PCB P/N DESIGNATION: MGP50 - 1002 - F T W material and layout (i.e. pad size, trace area, copper thickness, air flow, etc.). Typical temp. rise at full rated power is 30-50°C (Opt.S=50-70°C). RCD Type Options: S, P, F (leave blank if std) Resis. Code: ≤ ≤ ≤ ≤ ≤1%: 3 signif. figures & multiplier, APPLICATION NOTE #2: Resistor Selection e.g. R100= 0.1Ω, 1R00= 1Ω, 10R0=10Ω,1000= 100Ω, 1001= 1KΩ. MGP resistors are ideal for semi-precision SM applications and are Resis. Code 2% - 10%: 2 signif. figures & multiplier, generally more economical than thin film rectangular chips. For less e.g. R10= 0.1Ω, 1R0= 1Ω,100= 10Ω, 101=100Ω,102= 1K, 103=10K. critical applications, consider low cost MCF carbon film melf resistors. Tolerance: F=1% (std), B=0.1%, C=.25%, D=.5%, G=2%, J=5% For increased performance, especially in high humidity applications Packaging : B = Bulk, T = Tape & Reel (such as Naval or tropical environments), consider MHM series. If flat Optional TC: 10=10ppm, 25=25ppm, 50=50ppm (leave blank if std) chips are preferred, consider BLU series (precision) or MC series (semi- precision/ general purpose). For higher power, consider MPF series. Termination: W= Lead-free, Q= Tin/Lead (leave blank if either is acceptable) - - - - RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603 669 0054 Fax: 603 669 5455 Email:sales@rcdcomponents.com FA031D Sale of this product is in accordance with GF-061. Specifications subject to change without notice. 20 Peak Power (Watts)