RCD PR2-101-JBW

RoHS RESISTORSCAPACITORSCOILSDELAY LINES SURGE RESISTORS, 1/8W to 15W, 2KV to 25KV RCD PR2 Term.”W” 10K 5% is Pb-free PR SERIES and RoHS compliant; “Q” is Sn-Pb  Cost effective high-voltage surge resistors to 200 joules Excellent Low Cost Replacement for Composition Resistors TM  Available on RCD’s exclusive SWIFT program Series PR pulse resistors withstand higher energy pulses than conven- tional film & wirewound types, without the performance disadvantages  Molded surface mount version available (PRM series) of carbon comp resistors. The heavy duty construction features a high OPTIONS thermal conductivity core and coating, enabling improved stability and  Opt. ER: Group A Screening per MIL-R-39008 RCR environmental performance. Series PR satisy a wide variety of pulse  Opt. F: Flameproof coating applications including lightning, snubber, in-rush current, capacitor  Opt. B: Increased power (see Specifications table) charge, etc. RoHS (Sn) or Mil-spec (Sn-Pb) termination finish available.  Opt. X: Non-inductive (see Performance Char. table) → D ← ← H → ← L →  Custom marking, cut & form, burn-in, etc. d ↓ Inch [mm] ↑ SPECIFICATIONS Max. Max. Wattage Rating RCD Resistance 6 4 Continuous Peak Pulse L (Body Length) D (Body Dia.) d±.004 [.1] H (min) 5 Type Range 1,5,8 2,5,8 Standard Option B Voltage Voltage PR1/8 1/8W 1/2W 150V 2KV 0.1W-2K .145±.025 [3.69±.64] .062±.015 [1.6±.38] .018 [.46] 1.0 [25.4] PR1/4 1/4W 1W 250V 3.5KV 0.1W-10K .240±.032 [6.1±.8] .085±.025 [2.16±.64] .022 [.56] 1.0 [25.4] PR1/2 1/2W 2W 350V 5KV 0.1W-24K .375±.040 [9.2±1] .156±.025 [3.96±.64] .028 [.7] 1.25 [32] 3 PR1 1W 4W 500V 10KV 0.1W-100K .600±.040 [15.2±1] .225±.032 [5.72±.8] .031 [.8] 1.25 [32] 3 7 PR2 2W 5W 750V 15KV 0.1W-200K .875±.062 [22.2±1.6] .312±.040 [7.92±1] .039 [1] 1.375 [35] PR5 5W 10W 800V 18KV 0.1W-220K 1.05±.062 [26.7± 1.6] .350±.040 [8.89±1] .039 [1] 1.375 [35] PR10 10W 15W 1000V 25KV 0.1W-510K 1.72±.062[43.7±1.6] .350±.040 [8.89±1] .039 [1] 1.375 [35] 1 2 3 Max voltage = √(PxR), not to exceed value listed. Pulse voltage & energy capability is dependent on res.value, waveform, repetition rate, & environmental conditions (refer to R-42 for derating factors). .040” (1mm) lead 4 5 dia. is available on PR1 (specify PR1-18), .032” [.8mm] lead dia. is available on PR2 (specify PR2-20) Lead length is for bulk packaging, taped parts may be shorter (consult taping dimensions). Expanded range avail. 6 7 8 Allow .024” [.6mm] additonal for Opt. X or values <1W Specify Opt. 56 for 1.5” [38.1] min. lead length, Opt. 70 for 2” [50.8] lead length Multiply by 0.7 on Opt.X parts. SURGE CAPABILITY 1000 100 10 PR10 PR5 PR1/2 PR2 PR1 1 PR1/4 PR1/8 0.1 0.25 0.5 .75 1 2.5 5 7.5 10 25 50 75 100 250 500 750 1K 2.5K 5K 7.5K 10K 25K 50K 75K 100K Resistance Value (ohms) PERFORMANCE CHARACTERISTICS, Typ. APPLICATION NOTE Use chart above to select model to meet desired surge level. Pulse not to exceed PR1/8-PR2: 1.25%/°C >70°C, Derating, Wattage & Voltage peak V & j ratings (derate 30% for Opt.X), and average power during repetitive PR5-PR10 & Opt. B: 0.8%/°C >25°C pulses nte rated W. A safety factor of 30% typ. is recommended for infrequent 0.2uH PR1/8X-PR1/2X,0.3uH PR1X-PR2X, pulses, 50% typ. for repetitive pulses (refer to Note R42 for derating factors at- Max.Induc*: Opt. X≤50W 0.7uH PR5X-PR10X tributable to pulse width, rep. rate, temp., altitude, humidity). Verify by evaluating under worst-case conditions. Depending on specifics, PR series can often satisfy 0.37uH PR1/8X-PR1/2X, 0.6uH PR1X- Max.Induc*: Opt. X>50W the surge requirements of UL-217, -268, -294, -497, -508, -913, -943, -991, -1459, PR2X, 1.4uH PR5X-PR10X -1971, ANSI/IEEE C62.41, CCITT (Rec. K17), Bellcore TR-NWT-001089 & TR- Short-time Overload ±0.5% TSY-000057, CSA C22.2-225, IEC 664, IEC 801.5, IEEE587, Can.Doc. CS-03, Temperature Cycling ±0.5% FCC Part 68., etc. Consult factory for assistance. TCR (20 & 50ppm avail.) ±100ppm/°C(<0.2W=200ppm) P/N DESIGNATION: PR1/2 - 102 - K T W Moisture Resistance ±1% RCD Type Shock and Vibration ±0.2% Options: X, S, F, ER, B (leave blank if std) Effect of Soldering ±0.2% Resis. Code 1% tol: 3 signif. figures & multiplier, Voltage Coefficient ±0.005%/V e.g. R100=0.1W, 1R00=1W, 10R0=10W, 1000=100W, 1001=1K. 2%-10%: 2 signif.fig. & multiplier (R10=0.1W, 1R0=1W, 100=10W, 102=1K) Load Life ±0.5% Std, ±1% Opt.B Tolerance: J=5% (standard), F=1%, G=2%, K=10% Operating Temp Range -55 to +150°C, +275°C avail. Packaging: B = bulk, T = Tape & Reel Dielectric Strength (1KV avail.) 500V (PR1/8 & PR1/4 =300V) Optional TC: 20 =20ppm, 50= 50ppm (leave blank if standard) * specify Opt.75 for induc levels 50% that of Opt.X, or Opt.76 for 33% that of Opt.X Termination: W= RoHS (std), Q= Tin/Lead (leave blank if either is acceptable) - - - - RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603 669 0054 Fax: 603 669 5455 Email:sales@rcdcomponents.com FA029K Sale of this product is in accordance with GF-061. Specifications subject to change without notice. 73 Energy Rating, Joules (j)