SL POWER GECA20-12G
Specifications
Manufacturer
SL Power
Manufacturers Part #
GECA20-12G
Selling Alternatives
GSC20-12G
Brand
Condor
Series
GECA20
Factory Pack Quantity
1
Application
General Purpose
Connection Type
Molex/JST
Convection Rating
20 W
Cooling Method
Convection
Dimensions
3.50 x 2.00 x 0.85"
Efficiency
80%
Environmental Conditions
General Purpose
Industry
Industrial
Input Type
AC
Mechanical Style
Open / Enclosed Frame
Number of Outputs
1
Operating Temperature
0 to +45°C, Full Load
Output Amps 1
1.67 A
Output Voltage V1 Nominal
12 V
Package Type
Open Frame
Power
20 W
Subcategory
AC-DC Power Supply
Datasheet
Extracted Text
SL POWER GECA20 SERIES GECA20 20 Watt Power Supply 20 Watt Series Measures: 3.50 x 2.00 x 0.85” Commercial Wide-Range Input 2 Year Warranty • Wide-Range AC Input 90-264 VAC • Low Height Footprint - 3.5”x 2”x 0.85” • Conducted EMI Exceeds FCC Class B and CISPR 22 Class B • Single Output Models in Four Popular Voltages • Approved to UL60950-1: 2003, CSA-22.2 No. 60950-1-03, IEC and EN60950-1 • CB Report Available • RoHS Compliant • Marked to LVD Unless otherwise noted, all parameters are nominal values measured at 120 VAC @25˚C and 0-95% Specifications relative humidity, non-condensing. For limits at unusual operatiing conditions, consult factory. AC Input Output Noise 90-264 VAC, 47-63 Hz single phase. 0.5% RMS, 1% Pk-Pk, 20 MHz bandwidth, differential mode. Measured with scope probe directly across output terminals of the power supply with load Input Current terminated with 0.1μF capacitor. Maximum input current at 120 VAC, 60 Hz with full load: 0.5 A. Transient Response Hold-Up Time Main Output - 500 μs typical response time for return to within 0.5% of final 10 ms minimum from loss of AC input at 20 W load, nominal line (120 VAC). value for a 50% load step within the regulation limits of minimum and Output Power maximum load, ∆i/∆t< 0.2 A/μs. Maximum voltage deviation is 3.5%. Normal continuous output power is 20 W, 25 W peak for 60 s. Start-up overshoot less than 5% under nominal conditions; less than 2% under all conditions at shutdown. Overload Protection Fully protected against short circuit and output overload. Short circuit Switching Frequency protection is cycling type power limit. Factory set to begin power limiting 70 kHz +/-10 kHz. at approximately 27 W. Voltage Adjustment Overvoltage Protection See table for individual model features. Adjustable voltage outputs Built in with firing point set per grid at top of next page. OVP firing shuts are preset at factory. Outputs are capable of a minimum of +/- 5% change down the converter. from nominal setting. Efficiency EMI/EMC Compliance 72 to 80% depending upon model. All models include built-in EMI filtering to meet the following emissions requirements: Turn-on Time Less than 1 s at 120 VAC, 25°C (inversely proportionate to input voltage and EMI SPECIFICATIONS COMPLIANCE LEVEL thermistor temperature). Conducted Emissions EN55022 Class B; FCC Class B Input Protection Static Discharge EN61000-4-2, Level 3 Internal AC fuse provided on all units. Designed to blow only if a catastrophic RF Field Susceptibility EN61000-4-3, Level 3 failure occurs in the unit. Fuse does not blow on overload or short circuit. Fast Transients/Bursts EN61000-4-4, Level 3 Surge Susceptibility EN61000-4-5, Level 3 Inrush Current Inrush is limited by internal thermistor. The inrush at 240 VAC, averaged Safety Approvals over the first AC half-cycle under cold start conditions will not exceed 37A. SL Power Electronics, Corp. declares under our sole responsibility that all GECA models are in conformity with the applicable requirements of Temperature Coefficient EN60950 following the provisions of the Low Voltage Directive 73/23/EEC. 0.03%/°C typical on all outputs. All GECA models are approved to UL60950-1: 2003, Temperature Range CSA-22.2 No. 60950-1-03, IEC and EN60950-1 Designed for 0 to 45°C operation at full rated output power; derate output current and total output power by 2.5% per °C above 45°C. MTBF 120kHrs. SL Power Electronics, Corp. • 6050 King Drive • Ventura CA, 93003 • Phone:805.486.4565 • Fax:805.487.8911 • Email:info@slpower.com • www.slpower.com Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-GECA20-power-supply.html http://power.sager.com SL POWER GECA20 SERIES GECA20 20 Watt Power Supply 20 Watt Series Measures: 3.50 x 2.00 x 0.85” Commercial Wide-Range Input Commercial Output Current Line Load OVP Ripple & Model (V) Regulation Regulation Set Point Noise(P-P) GECA20-5G 5.1 V 4.0 A +/-0.5% +/-3% 7.0±1.0 V 1% GECA20-12G 12 V 1.67 A +/-0.5% +/-3% 16.8±2.4 V 1% GECA20-15G 15 V 1.34 A +/-0.5% +/-3% 21.0±3.0 V 1% GECA20-24G 24 V 0.84 A +/-0.5% +/-3% 33.6±4.8 V 1% Environmental Specifications GECA20 Series Mechanical Specifications ENVIRONMENT OPERATING NON-OPERATING CON 1: MOLEX P/N 26-60-4030, w/center PIN Removed Temperature (A) 0 to 45°C -40 to +85°C 0.156 [3.96 mm] CTR Header Humidity (A) 20 to 90% RH 10 to 95% RH Shock (B) 20 g 40 g CON 2: pk pk Altitude -500 to 10,000 ft -500 to 40,000 ft MOLEX P/N 26-60-4040, 0.156 [3.96 mm] CTR Header 2 2 Vibration (C) 1.5 g 0.0032 g /Hz 5 g 0.026 g /Hz rms’ rms’ Input J1 A. Units should be allowed to warm up/operate under non-condensing PIN 1) AC Line conditions before application of power. PIN 3) AC Neutral B. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, Output J2 3 orthogonal axes, total 6 shocks. Single Output C. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to PIN 1) + Output 2000Hz, 3 orthogonal axes. Tested for 10 min./axis operating and PIN 2) + Output 1 hr./axis non-operating. PIN 3) Common PIN 4) Common Mating Connector Housing P/N Contacts P/N MOLEX Input 09-50-3031 08-52-0072 Output 09-50-3041 08-52-0072 Note: 5A maximum recommended current per Connector PIN Weight 0.5 lbs Max [0.23 kg Max.] Tolerance X.XX=0.030 X.XXX=0.010 [0.mm] SL Power Electronics, Corp. • 6050 King Drive • Ventura CA, 93003 • Phone:805.486.4565 • Fax:805.487.8911 • Email:info@slpower.com • www.slpower.com Data Sheet © 2006 SL Power Electronics, Corp. The information and specifications contained in this data sheet are believed to be correct at time of publication. Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. Rev.8/31/06 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-GECA20-power-supply.html http://power.sager.com
Frequently asked questions
How does Electronics Finder differ from its competitors?

Is there a warranty for the GECA20-12G?

Which carrier will Electronics Finder use to ship my parts?

Can I buy parts from Electronics Finder if I am outside the USA?

Which payment methods does Electronics Finder accept?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods