SL POWER GPFC110-28

GPFC110 Commercial 110 Watt Global Performance Switchers 110 WATT GLOBAL PERFORMANCE SWITCHERS FEATURES: • 3.1 watts/cu.in. power density • Compact size (6.3” x 3.75” x 1.62”; meets 1U height) • Power factor corrected to IEC 1000-3-2 Class A • Less than 300 μA leakage • EMI compliance to CISPR 22, FCC Class B • Approved to UL1950, IEC950 and CSA 22.2 No. 950 • 2-year warranty • marked to LVD • RoHS Compliant Model Available (G suffix) SPECIFICATIONS Ac Input EMI/EMC Compliance 85-264 Vac, 47-63 Hz single phase. All models include built-in EMI filtering to meet the EMC requirements below. Input Current EMI SPECIFICATIONS COMPLIANCE LEVEL Maximum input current 2.3 A at 90 Vac, 60 Hz with full rated load. Input cur- Conducted Emissions EN55022 Class B; FCC Class B rent harmonic content meets the requirements of IEC1000-3-2. Static Discharge EN61000-4-2, 6 kV contact, 8 kV air Hold-up Time RF Field Susceptibility EN61000-4-3, 3 V/meter 25 ms minimum from loss of ac input at full load, nominal line (115 Vac). Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kHz Output Power Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com. 110 W fan cooled, 75 W convection. Peak ratings are for 60 s maximum dura- Line Frequency Harmonics EN61000-3-2 Class A tion, 10% duty cycle. Inrush Current Total Regulation Inrush 240 Vac is less than 37 A, averaged over the first ac half-cycle under cold Total regulation is the maximum deviation from the nominal voltage for all start conditions. Limiting provided by internal thermistors. steady-state loading conditions. Fan Output Overload Protection An additional output, same as Vout, suitable for powering a dc fan is included in all Fully protected against short circuit and output overload. Short circuit protec- models. The output is protected by an internal resistor in the event of an overload. tion is cycling type power limit. Recovery after fault is automatic. Output Noise Power Fail 0.5% rms, 1% pk-pk, 20 MHz Bandwidth, differential mode. Measured with TTL or CMOS compatible output goes low (<0.5 V) 8 ms before output voltage noise probe directly across output terminals of the power supply. drops more than 4% below nominal voltage upon loss of ac power. The signal is factory set to trip when input power can no longer sustain the output. Transient Response 500 μs typical response time for return to within 0.5% of final value for a 50% Temperature Coefficient load step change, ∆i/∆ t< 0.2 A/μs. Maximum voltage deviation is 3.5%. Load 0.03%/°C typical on all outputs. must not go below stated minimum. Environmental Remote Sense Designed for 0 to 50°C operation at full rated output power; derate output current Provided as a standard feature. Capable of compensating for 0.25 V total of and total output power by 2.5% per °C above 50°C. See Environmental and Pack- cabling losses in voltage. Open sense lead protection. aging Specifications on the next page. Overvoltage Protection OVP crowbar reduces output voltage below nominal rating in less than 50 ms. Commercial Safety Approvals All models are approved to UL1950, CSA22.2 No. 950-95, IEC950, EN60950. CB Voltage Adjustment: Main output ±5%. certificate available. Exceeds FCC and CISPR22 Class B conducted emissions Input Protection requirement Internal ac fuse provided on all models. Fuse does not blow on overload or short circuit—fuse blows only if catastrophic failure occurs in the unit. O All specifications are typical at nominal input, full load at 25 C unless otherwise stated Commercial Output Output Output Total Model Output No. Output Minimum (A) Maximum (A) Maximum (B) Regulation OVP Setpoint Notes GPFC 110-5 1 5.1 v 0 A 11 A 15 A 2% 6.2 ± 0.6 V C GPFC 110-12 1 12 V 0 A 6.7 A 9.2 A 2% 14 ± 1.1 V C GPFC 110-15 1 15 V 0 A 5.3 A 7.3 A 2% 18.5 ± 1.5 V C GPFC 110-24 1 24 V 0 A 3.4 A 4.6 A 2% 28 ± 2.5 V C GPFC110-28 1 28 V 0 A 2.9 A 3.9 A 2% 34 ± 2.8 V C GPFC110-48 1 48 V 0 A 1.7 A 2.3 A 2% 55 ± 4 V C Notes: A. With unrestricted convection cooling. B. With 26cfm airflow. C. Add “G” suffix to part number for RoHS compliant model. GPFC110 MECHANICAL SPECIFICATIONS ENVIRONMENTAL SPECIFICATIONS OPERATING NON-OPERATING Temperature (A) See Individual Specs. -40 to +85°C A. Units should be allowed to warm up/operate under non-condensing conditions before application of power. Humidity (A) 0 to 95% RH 0 to 95% RH B. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, Shock (B) 20 g 40 g 3 orthogonal axes, total 6 shocks. pk pk C. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to Altitude -500 to 10,000 ft -500 to 40,000 ft 2000Hz, 3 orthogonal axes. Tested for 10 min./axis operating and 2 2 Vibration (C) 1.5 g 0.003 g /Hz 5 g 0.026 g /Hz rms’ rms’ 1 hr./axis non-operating. SL Power Electronics., 6050 King Drive, Bldg A, Ventura, CA 93003, USA. Phone:(805) 486 4565 Fax:(805) 487 8911 Email: info@slpower.com Rev. 8/12 Data Sheet © 2009 SL Power Electronics Inc. The information and specifications contained in this data sheet are believed to be correct at time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice.