SL POWER GPFM600-24

GPFM600 Medical 600 Watt Global Performance Switchers FEATURES: Small package (12.00” x 5.50” x 3.09”) Power factor corrected to EN61000-3-2 Class A Full load rating to 60°C 85 to 264 Vac Input Medically Approved to UL2601-1, IEC601-1, CSA C22.2 No. 601.1.2 2 year warranty marked to LVD SPECIFICATIONS: Ac Input Inrush Current 85-264 Vac, 47-63 Hz single phase. Limit inrush current to 125% of maximum operating current. Turn on time of the power supply not to exceed 3 Output Power seconds over the full input voltage and frequency range. Continuous output power, 600 watts. EMI/EMC Compliance Hold-upTime All models include built-in EMI filtering to meet emissions 20 ms minimum from loss of ac input until output reaches requirements: 3% below nominal. EMI SPECIFICATIONS COMPLIANCE LEVEL Conducted Emissions EN55011 Class B; FCC Class B Line and Load Regulation Static Discharge EN61000-4-2, 6 kV contact, 8 kV air ±1% over the entire input voltage and frequency range, RF Field Susceptibility EN61000-4-3, 3 V/meter and over the entire output current range. Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kHz Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com. Minimum Load No minimum load required. Vibration and Shock All models are to meet MIL-STD 810E, method 514.4 Overload Protection Category. Current limit 105% minimum, 125% maximum of the specified full load current. Environmental Designed for 0 to 60°C operation at full rated output Output Noise power; derate output current and total output power by 50 mV pk-pk maximum. 2.5% per °C above 50°C. Transient Response Medical Leakage Current Maximum of 5% change in Vout for a load change of 1.25 A. 150 µA under normal conditions. Maximum under single Recovers to ±1% within 500u sec. fault conditions, 250 µA. Patient sink leakage with 120 Vac, 60 Hz applied to any output with respect to the chassis will be less than 500 µA. Overvoltage Protection Built in on all models. OVP crowbar reduces output voltage below nominal rating in less than 50 ms. Output Medical Safety Agency Approved to UL2601-1, EN60601-1-2, CSA C22.2 No. voltage decay is dependent upon loading. 601.1.2. DC Power Good Optocoupler isolated output indicates that the DC output is equal to or greater than 21.6 (-0 + 0.25) volts. This signal shall be driven when in the active ‘DC Good’ state. Efficiency Minimum of 75% under full load and input of 120 Vac 60 Hz. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565  FAX 805-487-8911  www.condorpower.com 112 GPFM600 Medical 600 Watt Global Performance Switchers Output Commercial Model Output OVP Setpoint Total Regulation Noise P-P Maximum(A) Gc PFM600-24 2A 4 Va 2V 5 2% 5.8 ± 0.6 1V 100 m GPFM600 MECHANICAL SPECIFICATIONS INPUT: J1 MOLEX P/N 43160-31-3 PIN 1: AC LINE PIN 2: AC NEUTRAL PIN 3: EARTH GROUND OUTPUT: J2 MOLEX P.N. 39-29-1147 14 PIN RIGHT ANGLE HEADER PIN 1: +24 V PIN 2: +24 V PIN 3: +24 V RETURN PIN 4: +24 V RETURN PIN 5: N/A PIN 6: AC GOOD PIN 7: AC GOOD RETURN PIN 8: +24 V PIN 9: +24 V PIN 10: +24 V RETURN PIN 11: +24 V RETURN PIN 12: N/A PIN 13: DC GOOD PIN 14: DC GOOD RETURN Environmental Operating Non-operating Specification Dimensions: Inches TC emperature (A)0C to 60º -18 to +60º Millimeters HH umidity (A)0H to 97% R 0 to 97% R A. Units should be allowed to warm up/operate under non-condensing conditions Sg hock (B) 20 40 g pk pk before application of power. Cooling provided by internal fan— heatsink temperatures should not exceed 90ºC for extended periods in the installation. At ltitude-t 500 to 10,000 f -500 to 40,000 f B. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to 2000Hz, 3 orthogonal axes. Tested for 10 min./axis operating and 1 hr./axis non-operating. 5 g , 0.026 2 rms C. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3 orthogonal axes, Vg ibration (C) 1.5 , 0.003 g /Hz 2 rms g /Hz total 6 shocks. Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929  805-486-4565  FAX 805-487-8911  www.condorpower.com 113