SL POWER LE150S70CD

SL POWER LE150S-CD LE150S-CD SERIES 150W Single Output 150 Watt LED Power Supply LED Driver Series Measures: 9.37 x 3.13 x 1.81” Features  High Efficiency (up to 93%)  Wide Range Universal Input 90-305 VAC  Active Power Factor Correction (0.99 typical)  Constant Current Output  Dimming Function  Lightning Protection  Waterproof (IP67)  Overcurrent, Overvoltage, Overtemperature Protection  Meets UL8750 & EN61347 Safety  Minimum of 3 Year Warranty, Consult factory for 5 Years Description The LE150S-CD Series operate from a 90 ~ 305Vac input range. These units will provide up to a 1.4 A of output current and a maximum output voltage of 214Vdc for 150 W maximum output power. They are designed to be highly efficient and highly reliable. The standard features include dimming control, lightning protection, over voltage protection, short circuit protection, and over temperature protection. Model Selection Model Output Output Efficiency* Ripple & Regulation Overvoltage Number Current Voltage 110Vac 220Vac Noise** Line Load Trip Level LE150S140CD 1330mA-1470mA 53V – 107V 89%-90% 91%-92% 3.2V pk-pk max. ±1% ±3% 128V – 161V LE150S70CD 665mA-735mA 107V – 214V 90%-91% 92%-93% 6.5V pk-pk max. ±1% ±3% 257V – 321V Notes: 1. Efficiency measured at full load, at input voltage noted. 2. Measured at 20MHz bandwidth, with noise probe directly across output terminals, and load terminated with 0.1F ceramic and 10F low ESR electrolytic capacitors. General Specifications AC Input 90-305Vac, 47-63Hz, 1∅ Turn On Time 2.0 seconds, max. 1-10Vdc source or External Resistor can be 100Vac: 1.8A, 220Vac: 0.9A Dimming Input Current used for dimming control. See below. Function Constant Current Inrush Current 230Vac, cold start: will not exceed 65A Overload Protection Provided - no damage to unit, self-recovery. Short Circuit Input Fuses XA, 250VAC fuses provided on all models Protection Latch mode. AC input will need to be reset to Earth Leakage return to normal operation after an OVP Overvoltage <0.75mA@277Vac, 50Hz Current condition. See chart for trip range. Protection Latch mode. AC input will need to be reset To return to normal operation after an OTP See Models chart. Overtemperature Efficiency condition. Trip Temperature = 110°C typical. Protection Output Power 150W continuous Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. www.slpower.com LE150S-CD, 15-APRIL-13 1 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-le150s-cd-power-supply.html http://power.sager.com LE150S-CD SL POWER 150W Single Output LE150S-CD SERIES 150 Watt LED Power Supply LED Driver Series Measures: 9.37 x 3.13 x 1.81” General Specifications (continued) Operating Operating: -35°C to +70°C See chart Ripple and Noise Non-operating: -40°C to +85°C Temperature 10% to 100% operating Output Voltage See chart Relative Humidity 5% to 100%, non-operating UL8750, UL935, UL1012, CSA-C22.2 No. 107.1, Total Regulation +/- 3%. See chart Safety Standards EN61347-1, EN61347-2-13 340,000 hours (1400mA model, 110Vac input, Dimensions W: 3.13” x L: 9.37” x H: 1.81” MTBF 80% load, 25°C ambient, per MIL-HDBK-217F). 58,000 hours (1400mA model, at 110Vac input, Weight 1500g Lifetime 80% load, 45°C ambient temperature). EMI/EMC Compliance Emissions EN55015, Radiated & Conducted with 6db of margin EMI for Lighting Equipment EN61547 EN61000-4-2, 4kV Contact Discharge, 8kV air discharge Static Discharge Immunity Radiated RF Immunity EN61000-4-3 EFT/Burst Immunity EN61000-4-4 Line Surge Immunity EN61000-4-5, 2kV line-line, 4kV line-earth Conducted RF Immunity EN61000-4-6 EN61000-4-8 Power Frequency Magnetic Field Immunity Voltage Dip Immunity EN61000-4-11 Line Harmonic Emissions EN61000-3-2 Flicker Test EN61000-3-3 Derating Curves Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Mechanical Drawing www.slpower.com LE150S-CD, 15-APRIL-13 2 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-le150s-cd-power-supply.html http://power.sager.com LE150S-CD SL POWER 150W Single Output LE150S-CD SERIES LED Driver Series 150 Watt LED Power Supply Measures: 9.37 x 3.13 x 1.81” Dimming Control The dimming function shown below uses an internal pull-up resistor, with the output at full load when the dimming leads are not connected (floated). Parameters: Parameter Min. Typ. Max. Notes 10V Output Voltage 9.8V 10V 10.2V 10V Output Source Current 0mA - 10mA Absolute Max. Voltage on the 1-10V input -2V - 12V Source Current on the 1-10V input 0mA - 1mA Value of Rin (resistor inside the LED Driver, which is located 19.8K 20K 20.2K between the 1-10V input and 10V output Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. www.slpower.com LE150S-CD, 15-APRIL-13 3 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-le150s-cd-power-supply.html http://power.sager.com LE150S-CD SL POWER 150W Single Output LE150S-CD SERIES LED Driver Series 150 Watt LED Power Supply Measures: 9.37 x 3.13 x 1.81” LE150SXXXCD Dimming Configuration using External Voltage LE150SXXXCD Dimming Configuration using External Resistance Dimming Control Notes: 1. Io is actual output current and Ir is rated current without dimming control. 2. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 50% of the max. output voltage for any given model). 3. If the output voltage is maintained above 50% of the maximum output voltage, the dimming control may be operated over the entire 1-10V range with output current varying from 100% down to practically 10%. 4. The dimming signal is allowed to be less than 1V, however, when it for 0-1V, the output current is 10% Io. 5. The internal resistor Rin is 20K, and Vcc is about 15V. 6. Do not connect the GND of dimming to the output; otherwise, the LED driver cannot work normally. Data Sheet © 2012 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. www.slpower.com LE150S-CD, 15-APRIL-13 4 Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-le150s-cd-power-supply.html http://power.sager.com