SL POWER LE75S70CD

SL POWER LE75S-CD LE75S-CD SERIES 75W Single Output 75 Watt LED Power Supply LED Driver Series Measures: 5.91 x 2.66 x 1.46” Features  High Efficiency (up to 91%)  Wide Range Universal Input 90-305 VAC  Active Power Factor Correction (0.99 typical)  Constant Current Output  Dimming Function  Lightning Protection  Waterproof (IP67)  Overcurrent, Overvoltage, Overtemperature Protection  Meets UL8750 & EN61347 Safety  Compliant to ANSI/IEEE C62.41, Class A  Minimum of 3 Year Warranty, Consult factory for 5 years Description The LE75S-CD Series are constant current mode LED Driver power supplies that operate from a wide range input of 90 to 305Vac. These models provide up to 2.8A of output current, at a maximum output voltage of 108Vdc, at up to 75W output power. The LE75S-CD series are highly efficient and highly reliable. Features include dimming control, overvoltage protection, short circuit protection, and overtemperature protection. Model Selection Model Output Output Efficiency* Ripple & Regulation Overvoltage Number Current Voltage 110Vac 220Vac Noise** Line Load Trip Level LE75S28CD 2660mA-2940mA 13V – 27V 85%-87% 87%-89% 5% of Vo pk-pk ±1% ±3% 35V – 38V LE75S140CD 1330mA-1470mA 27V – 54V 86%-88% 88%-90% 5% of Vo pk-pk ±1% ±3% 65V – 70V LE75S70CD 665mA-735mA 54V – 108V 87%-89% 89%-91% 5% of Vo pk-pk ±1% ±3% 118V – 130V Notes: 1. Efficiency measured at full load, at input voltage noted. Efficiency will be 2% lower if measured immediately after start-up. 2. Measured at 20MHz bandwidth, with noise probe directly across output terminals, and load terminated with 0.1F ceramic and 10F low ESR electrolytic capacitors. 3. LE75S070CD: Non-Class 2 output (USR & CNR) 4. LE75S140CD: Class 2 output (USR), Non-Class 2 output (CNR) 5. LE75S280CD: Class 2 output (USR & CNR) General Specifications 90-305Vac, 47-63Hz, 1∅ 110Vac: 0.8s – 1.2s AC Input Turn On Time 120–370Vdc 220Vac: 0.4s – 0.6s Dimming 1-10Vdc source or External Resistor can be used Input Current 100Vac: 0.9A, 220Vac: 0.42A for dimming control. See below. Function Inrush Current 230Vac, cold start: will not exceed 50A www.slpower.com LE75S-CD 15-April-13 1 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-le75s-cd-power-supply.html http://power.sager.com LE75S-CD SL POWER LE75S 75W -CD SERIES Single Output 75 Watt LED Power Supply LED Driver Series Measures: 5.91 x 2.66 x 1.46” General Specifications (continued) Overload XA, 250VAC fuses provided on all models Constant Current Input Fuses Protection Earth Leakage Short Circuit <1mA@277Vac, 50Hz Provided - no damage to unit, self-recovery. Current Protection Latch mode. AC input will need to be reset to Overvoltage Efficiency See Models chart. return to normal operation after an OVP condition. Protection See chart for trip range. Latch mode. AC input will need to be reset to Overtemperature Output Power 75W continuous return to normal operation after an OTP Protection condition. Trip Temperature = 110°C typical. Operating Operating: -35°C to +70°C Ripple and Noise See chart Non-operating: -40°C to +85°C Temperature Relative 10% to 95% operating See chart Output Voltage Humidity 5% to 100%, non-operating UL8750, UL935, UL1012, UL1310 Class 2; Total Regulation +/- 3%. See chart Safety Standards CSA-C22.2 No. 107.1, CSA C22.2 No. 223-M91 Class 2; EN61347-1, EN61347-2-13 450,000 hours (2800mA model, at 110Vac input, Dimensions W: 2.66” x L: 5.91” x H: 1.46” MTBF 80% load, 25°C ambient, per MIL-HDBK-217F). 65,000 hours (2800mA model, at 110Vac input, Weight 750g Lifetime 80% load, 45°C ambient temperature. EMI/EMC Compliance Emissions EN55015, Radiated & Conducted with 6db of margin EN61547 EMI for Lighting Equipment Static Discharge Immunity EN61000-4-2, 4kV Contact Discharge, 8kV air discharge Radiated RF Immunity EN61000-4-3 EFT/Burst Immunity EN61000-4-4 Line Surge Immunity EN61000-4-5, 2kV line-line, 4kV line-earth EN61000-4-6 Conducted RF Immunity Power Frequency Magnetic Field Immunity EN61000-4-8 Voltage Dip Immunity EN61000-4-11 EN61000-3-2 Line Harmonic Emissions Flicker Test EN61000-3-3 ANSI/IEEE C62.41-1991: Class A operation. Line transient of 7 strikes of a 100kHz ring wave, Transient Protection 2.5kV level, common and differential mode. www.slpower.com LE75S-CD 15-April-13 2 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-le75s-cd-power-supply.html http://power.sager.com LE75S-CD SL POWER 75W Single Output LE75S-CD SERIES LED Driver Series 75 Watt LED Power Supply Measures: 5.91 x 2.66 x 1.46” Derating Curves Life Time vs. Case Temperature Curve Mechanical Drawing www.slpower.com LE75S-CD 15-April-13 3 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-le75s-cd-power-supply.html http://power.sager.com LE75S-CD SL POWER 75W Single Output LE75S-CD SERIES LED 75 W Driv att LED P er Serie ower Supply s Measures: 5.91 x 2.66 x 1.46” Dimming Control The dimming function shown below uses an internal pull-up resistor, with the output at full load when the dimming leads are not connected (floated). Parameters: Parameter Min. Typ. Max. Notes 10V Output Voltage 9.8V 10V 10.2V 10V Output Source Current 0mA - 10mA Absolute Max. Voltage on the 1-10V input -2V - 12V Source Current on the 1-10V input 0mA - 0.5mA Value of Rin (resistor inside the LED Driver, which is located 19.8K 20K 20.2K between the 1-10V input and 10V output LE75SXXXCD Dimming Configuration using External Voltage Dimming Configuration using External Voltage LE75SXXXCD Dimming Configuration using External Resistance Dimming Control Notes: 1. If the dimming function is not used, leave the dimming leads unconnected (floating). 2. Io is the actual output current and Ir is the rated current without dimming control. 3. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (~50% of the maximum output voltage for the specific model). 4. If the output voltage is maintained above 50% of the maximum output voltage, the dimming control may be operated over the entire 1-10V range with the output current varying from 100% down to ~10% of nominal. 5. The dimming signal may be <1V, but if this voltage is <1V, the output current can only maintain ~10% Ir. When the signal voltage is ~8.5-10V, the output current can maintain ~100% Ir. 6. Do not connect the GND of the dimming leads to output. The driver will not function normally if it is. Data Sheet © 2012 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. www.slpower.com LE75S-CD 15-April-13 4 Specifications are subject to change without notice. It is responsibility of each customer to thoroughly test each product and part number under their unique parameters and environments to ensure a product will work properly and reliably. Click below for more details, to buy on-line or request volume pricing: (866) 588-1750 power@sager .com http://power.sager.com/sl-power-le75s-cd-power-supply.html http://power.sager.com