SL POWER MAX-403-0512

400, 500 WATTS MULTIPLE OUTPUT MAX-400 MAX-500 MTC-500 Option F Option C STANDARD MAX SERIES Option V MODEL PWR OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 MAX-403-0512 400 +5V @ 70A +12V @ 10/16A pk -12V @ 6A MAX-503-0512 500 +5V @ 80A +12V @ 10/16A pk -12V @ 10A Featuring: MAX-504-1205 500 +5V @ 80A +12V @ 10/16A pk -12V @ 10A 5.2V @ 2A 3 • Over 3.5 watts/in power density MAX-504-1212 500 +5V @ 80A +12V @ 10/16A pk -12V @ 10A 12V @ 2A MAX-504-1224 500 +5V @ 80A +12V @ 10/16A pk -12V @ 10A +24V @ 2A • 80% overall efficiency MAX-504-1252 500 +5V @ 80A +12V @ 10/16A pk -5.2V @ 10A 12V @ 2A • VMEbus and Multibus II system compatibility TELECOM MTC SERIES • Meets international safety agency MODEL PWR OUTPUT #1 OUTPUT #2 OUTPUT #3 requirements MTC-503-0512 500 +5V @ 70A +12V @ 10A -12V @ 10A • All outputs regulated ±1% MTC-503-0515 500 +5V @ 70A +15V @ 8A -15V @ 8A • High peak currents for motor starting • System air or self-cooling options VMEbus and Multibus compatibility is High-current auxiliary outputs provide • AC automatic line selection option only one feature of this series. You’ll find regulation characteristics for proper switchers to power up to 80 Amps of operation of line drivers, network inter- logic and four hard disk drives — with faces, and RS232-type outputs. And, up to 16 Amps peak current to meet you can upgrade power output by 25% peripheral startup needs. without redesigning for a larger power You’ll find the outputs you need for supply. ISDN, LAN, T1 applications and for standard voice and data networks. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com 400, 500 WATTS 11.5” x 5”x 2.5” MAX-400, 500 MTC-500 MAX, MTC-500 MAX, MTC-500 with Option F 4.5 lbs - 2.0 kgs 5.2 lbs - 2.4 kgs Dimensions: Inches Millimeters SPECIFICATIONS: ALL MODELS INPUT AC Input: 90-132 Vac/180-264 Vac, 47 to 63 Hz. User selectable. See option “A” for automatic Option “G”, DC Power Good: Provides a TTL “1” open collector when output #1 is above 4.6 line selection. Internally fused for 12 A. V nominal. Not available if option “P” is selected. Inrush: Cold start AC current is less than 80 A at 115 Vac and 20 A at 230 Vac. Limited by Option “P”, AC Power Fail: Provides TTL “0” 5 ms before output voltage goes out of thermistor. regulation band upon loss of AC power. VMEbus compatible, provides 48 mA sink current Holdup Time: 16 ms minimum after removal of power, at nominal line, full load. capability. Not available if option “G” is selected. Efficiency: 80% typical. Option “V”, Fan/Cover Assembly: Low profile, end venting cover with integral ball-bearing Brownout Protection: Holds regulation to 85 Vac or 170 Vac. fan. OUTPUT Consult factory for other available options. Adjustability: User adjustable ±5% minimum. Line & Load Reg: ±1% over AC input range and 0 to 100% load change. Output #1 requires AC INPUT minimum load of 10%. FUNCTION 115 VAC 230 VAC CONNECTORS Ripple & Noise: Less than 1% p-p or 100 mV, whichever is greater. Input Select Short Open 0.250 Male Fastons Remote Sense (Output #1): Compensates for 250 mV total line drop. Open sense lead protection. TB1- (L) Line Line 1 Barrier strip Temperature Coefficient: 0.02% per degree C. #6-32 screws TB1- (N) Neutral Line 2 Stability: 0.1% over 8 hours after 30 minutes warm-up. 3/8 centers. TB1- ( ) Safety Ground Safety Ground Transient Response (Output #1): Output voltage returns to within 1% in less than 500 µs for a 50% load change. Peak transient does not exceed 5%. DC OUTPUT Overload Protection: All outputs are protected against overload and short circuit. Automatic FUNCTION LOCATION NOTES CONNECTOR recovery upon removal of fault. Overvoltage Protection (Output #1): Protects load against power supply induced overvoltage. Output #1 Terminal marked +V Main Output Bus bars Trip point is factory set so that output voltage cannot exceed 136% of nominal. #1/4-20 screws Terminal marked COM Rtn (Common) Remote Inhibit: Contact closure to the negative sense line drops output power to nominal Output #2 TB2-3 zero. TB2-4 Rtn (Common) Reverse Voltage: Protected against reverse voltage up to supply current rating. Output #3 TB2-5 Barrier Strip ENVIRONMENTAL TB2-4 Rtn (Common) #6-32 screws Thermal Protection: Shuts down power supply if overheated. Automatic recovery. 3.8” centers Temperature Range: 0° to 50°C at full ratings. Derate to half power at 70°C. Output #4* TB2-1 (+) Safety Agencies: Most models are approved to UL1950; CSA 22.2 #234; IEC 950 and TÜV (If provided) TB2-2 (–) EN60950, Class 1 SELV., CE 72/23/EEC/93/68EEC (low voltage directive). Conducted RFI: Meets FCC Part 15, Subpart J, Class A; EN55022 Class B; CISPR 22 Class B. *Rtn connected to common only if output is polarized in product selection chart Cooling: 30 CFM required to achieve full ratings. STATUS AND CONTROL Output Isolation: Isolated from ground 50 Vdc. FUNCTION LOCATION NOTES CONNECTOR Remote Sense J1-1 (+S) Output #1 Sense AMP MTA type OPTIONS: #640456-4 pin J1-2 (-S) Output #1 Sense Rtn Option “A”, AC Auto-Range: Automatically selects proper AC line voltage range to enable header (locking) AC Power Fail or J1-3 (PF) Reference to J1-2 power operation at either 115 or 230 Vac without user intervention. Option “C”, Cover: Limits contact with power supply interior. DC Power Good* Option “F”, Fan/Cover Assembly: Cover with integral ball-bearing fan provides proper cooling Inhibit J1-4(1H) Short to J1-2 to achieve full ratings at 50°C ambient temperature. *Optional function Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com