SL POWER MAX-754-1252

700, 750 WATTS MULTIPLE OUTPUT MAX-700 MAX-750 MSC-750 Option F Featuring: STANDARD MAX SERIES 3 • Over 4 watts/in power density MODEL PWR OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 • 80% overall efficiency MAX-703-0512 700 +5V @ 100A +12V @ 12/20A pk -12V @ 10A • VMEbus and Multibus II system MAX-704-1205 700 +5V @ 100A +12V @ 12/20A pk -12V @ 10A 5.2V @ 2A compatibility MAX-753-0512 750 +5V @ 120A +12V @ 12/20A pk -12V @ 10A MAX-754-1205 750 +5V @ 120A +12V @ 12/20A pk -12V @ 10A 5.2V @ 2A • Meets international safety agency MAX-754-1212 750 +5V @ 120A +12V @ 12/20A pk -12V @ 10A 12V @ 2A requirements MAX-754-1224 750 +5V @ 120A +12V @ 12/20A pk -12V @ 10A +24V @ 2A • All outputs fully regulated ±1% MAX-754-1252 750 +5V @ 120A +12V @ 12/20A pk -5.2V @ 10A 12V @ 2A • High peak current for motor starting • AC automatic line selection option MASS STORAGE MSC SERIES MODEL PWR OUTPUT #1 OUTPUT #2 OUTPUT #3 Specify the appropriate MAX-700 or MSC-753-0512 750 +5V @ 120A +12V @ 20/27A pk -12V @ 6A MAX-750 and get new design freedom for your high-end computer products. Use a system air cooled MAX-700, an optional self-cooled MAX-700 or standard self- cooled MAX-750. You can reduce your product size by replacing an 11” x 8” x 5” unit with a 58% smaller MAX-750. Build in power supply redundancy by replacing one ordinary switcher with two MAX-700s in the same space. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com 700, 750 WATTS 13.5”x 5”X 2.6” MAX-700, 750 MSC-750 MAX-700 MAX-700, MSC-750 with Option F, MAX-750, 6.1 lbs - 2.8 kgs 6.4 lbs - 2.9 kgs Dimensions: Inches Millimeters SPECIFICATIONS: ALL MODELS INPUT Option “G”, DC Power Good: Provides a TTL “1” open collector when output #1 is above 4.6 AC Input: 90-132 Vac/180-264 Vac, 47 to 63 Hz. User selectable. See option “A” for V nominal. Not available if option “P” is selected. automatic line selection. Internally fused for 15 A. Option “P”, AC Power Fail: Provides TTL “0” 5 ms before output voltage goes out of Inrush: Cold start AC current is less than 90 A at 115 Vac and 30 A at 230 Vac. Limited by regulation band upon loss of AC power. VMEbus compatible, provides 48 mA sink current thermistor. capability. Not available if option “G” is selected. Holdup Time: 16 ms minimum after removal of power, at nominal line, full load. Efficiency: 80% typical. Consult factory for other available options. Brownout Protection: Holds regulation to 85 Vac or 170 Vac. AC INPUT OUTPUT FUNCTION 115 VAC 230 VAC CONNECTOR Adjustability: User adjustable ±5% minimum. Line & Load Reg: ±1% over AC input range and 0 to 100% load change. Output #1 requires Input Select Short Open 0.250 Male Faston minimum load of 10%. TB1- (L) Line Line 1 Barrier strip Ripple & Noise: Less than 1% p-p or 100 mV, whichever is greater. TB1- (N) Neutral Line 2 # 6-32 screws Remote Sense (Output #1): Compensates for 250 mV total line drop. Open sense lead 3/8” centers TB1- ( ) Safety Ground Safety Ground protection. Temperature Coefficient: 0.02% per degree C. DC OUTPUT Stability: 0.1% over 8 hours after 30 minutes warm-up. Transient Response (Output #1): Output voltage returns to within 1% in less than 500 µs for FUNCTION LOCATION NOTES CONNECTOR a 50% load change. Peak transient does not exceed 5%. Output #1 Terminal marked +V Main Output Bus bars Overload Protection: All outputs are protected against overload and short circuit. Automatic #1/4-20 screws Terminal marked COM Rtn (Common) recovery upon removal of fault. Output #2 TB2-3 Overvoltage Protection (Output #1): Protects load against power supply induced overvoltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. TB2-4 Rtn (Common) Barrier strip Remote Inhibit: Contact closure to the negative sense line drops output power to nominal zero. #6-32 screws Output #3 TB2-5 Reverse Voltage: Protected against reverse voltage up to supply current rating. 3/8” centers TB2-4 Rtn (Common) ENVIRONMENTAL Output #4* TB2-1 (+) Thermal Protection: Shuts down power supply if overheated. Automatic recovery. (If provided) TB2-2 (-) Temperature Range: 0° to 50°C at full ratings. Derate to half power at 70°C. Safety Agencies: Most models are approved to UL1950; CSA 22.2 #234; IEC 950 and TÜV *Rtn connected to common only if output is polarized in product selection chart EN60950, Class 1 SELV., CE 72/23/EEC/93/68EEC (low voltage directive). STATUS AND CONTROL Conducted RFI: Meets FCC Part 15, Subpart J, Class A; EN55022 Class B; CISPR 22 Class B. Cooling: 30 CFM required to achieve full ratings. FUNCTION LOCATION NOTES CONNECTOR Output Isolation: Isolated from ground 50 Vdc. J1-1(+ S) Output #1 Sense AMP MTA type Remote Sense #640456-4 pin J1-2 (– S) Output #1 Sense Rtn OPTIONS: header (locking) AC Power Fail, or J1-3 (PF) Reference to J1-2 Option “A”, AC Auto-Range: Automatically selects proper AC line voltage range to enable DC Power Good* power operation at either 115 or 230 Vac without user intervention. Inhibit J1-4 (IH) Short to J1-2 Option “F”, Fan/Cover Assembly: Cover with integral ball-bearing fan provides proper cooling *Optional function to achieve full ratings at 50°C ambient temperature. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com