SL POWER MW153KB1503F01

MW153KB Universal 25-40 Watt Series • 100-240 VAC Universal Input • Desktop Style • Single Output to 40W • Four Models Available; 12V to 24V • Regulated Output with Low Ripple • Impact Resistant Polycarbonate Enclosure • Modified and Custom Designs Also Available • Designed to Meet EISA Requirements — see reverse side for details International Safety Standard Approvals Specifications Output Specifications General Specifications Line and Load Line Voltage +/-1% Topology Switching-Fixed Regulation (Excluding cord) Load Voltage +/-5% Frequency Flyback Ripple 1% Vp-p max. Efficiency Designed to Meet EISA Requirements — see Transient Response 0.5ms for 50% reverse side Load change Typical Hold-up Time @115VAC 18ms min. Protection Over-current Protection (Hiccup) Dielectric Withstand 4,000VAC or 5,656VDC Short Circuit Protection Primary - Secondary; 1,500VAC or 2,150VDC Primary-F.G; 500VDC Input Specifications Secondary-F.G Input Voltage Range Universal input 100-240VAC -10%, +10% Storage Temp -30° C to 85° C Line Frequency 47-63Hz Approvals and UL60601-1 Safety Standards IEC/EN60601-1 Input Current 90VAC Input 0.4A max. EMC : EN60601-1-2/EN55024 Protection Internal Primary MTBF 100,000 Calculated Hours Current Fuse, Inrush Limiting Case and Dimension Desktop style 3.98L x 2.4W x 1.34H (in) 101L x 61W x 34H (mm) Environmental Specifications Case Material Black 94V0 Polycarbonate Thermal Performance Operating temperature 0° C to 40° C full load, no derating Cord and Connectors 18 AWG 1,500mm convectional cooling 2 Conductor. Ault #3 Non vented case Connector. Other connectors are also available. Relative Humidity Non-condensing 5% to 95% Altitude 0-10,000 feet SL Power Electronics Corp • 6050 King Drive • Ventura, CA 93003 • Phone:805.486.4565 • Fax:858.712.2040 • Email:info@slpower.com • www.slpower.com MW153KB Universal 25-40 Watt Series For the most current data and application support visit www.slpower.com Output Current Output Max Ripple Ault Part Number Voltage Max Watts Vp-p max. MW153KB12XX 12 V 3.40 A 40.8 W 120 mV MW153KB15XX 15 V 2.70 A 40.5 W 150 mV MW153KB18XX 18 V 2.20 A 39.6 W 180 mV MW153KB24XX 24 V 1.70 A 40.8 W 240 mV Ault Part Number Key Pin Connections MW153 K B 12 XX Product Manufacturing Design Voltage Connector Family Location Revision DC Number Name Changes Input Configuration Pinout Code Center contact: positive IEC320 IEC320 N. America/ Europe IEC320 IEA Cu 3s 2t0 ralian N Sh . A av m ee rrica/ Europe Australian Shaver United United w/ground Japan C8 w/ground w/o ground Japan (M) w(/E o) ground C8 (M) Kingdom (E) Description Switchcraft 760 plug or equivalent Kingdom C14 C18 (B) C14 C18 ((B N)) (N) (G) (G) (F) (Q) (F) (Q) Suggested Mating Switchcraft 712A jack or equivalent Specify the Input Configuration Code in your order. Other Connectors are available by special order 2007 Energy Independence and Security Act – EISA The Energy Independence and Security Act of 2007 was passed in December of 2007 and addresses minimum efficiency standards and standby levels for Class A external power supplies that are 250 watts and under. This law stipulates that external power supplies manufactured on July 1, 2008 and beyond meet certain minimum efficiency and standby criteria as defined below. Minimum Efficiency Criteria Active mode is defined as when a power supply’s input is connected to line voltage AC and its output is connected to a DC or AC load drawing a portion of the product’s power output. Depending on the power rating for the power supply, it must meet the minimum efficiency criteria outlined below. Energy-Efficiency Criteria for Active Mode: output power on minimum average adapter label efficiency percentage 0 to ≤ less than 1 watt ≥ 0.50 * output power on adapter label > 1 to ≤ 51 watts ≥ [0.09 * Ln (output power on adapter label )] + 0.50 > 51 watts ≥ 0.85 The power supply must also meet a requirement for when its input is connected to a line voltage AC but its output is not connected to a load. Depending on the power output of the supply, it must keep its energy consumption below the following values. Energy Consumption Criteria for No Load Mode: output power on maximum power consumption adapter label in no-load mode 0 to < 250 watts ≤ 0.5 watts SL Power Electronics Corp • 6050 King Drive • Ventura, CA 93003 • Phone:805.486.4565 • Fax:858.712.2040 • Email:info@slpower.com • www.slpower.com Data Sheet © 2008 SL Power Electronics Corp. The information and specifications contained in this data sheet are believed to be correct at time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. Rev.6/9/08