SL POWER NMX-1003-0512

1000 WATTS POWER FACTOR CORRECTED MULTIPLE OUTPUT, FORCED CURRENT SHARING NMX-1000 Featuring: STANDARD NMX SERIES • Forced current sharing for N +1 MODEL PWR OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 redundancy NMX-1003-0512 1000 +5V @ 150A +12V @ 20/30A pk -12V @ 10A • Remote sense on outputs #1, 2 NMX-1004-1203 1000 +5V @ 150A +12V @ 20/30A pk -12V @ 10A 3.3V @ 10A and 3 NMX-1004-1205 1000 +5V @ 150A +12V @ 20/30A pk -12V @ 10A 5V @ 10A • “Zero wire” slope program current NMX-1004-1212 1000 +5V @ 150A +12V @ 20/30A pk -12V @ 10A 12V @ 10A NMX-1004-1224 1000 +5V @ 150A +12V @ 20/30A pk -12V @ 10A 24V @ 5A sharing on outputs #2 and 3 for NMX-1004-1512 1000 +5V @ 150A +15V @ 20/30A pk -15V @ 10A 12V @ 10A redundancy NMX-1004-1524 1000 +5V @ 150A +15V @ 20/30A pk -15V @ 10A 24V @ 5A • Universal AC input • 0.99 power factor • Mag-Amp regulators eliminate interaction between logic and The smallest most capable 1000 W auxiliary outputs power supply of its kind. When used with external OR-ing • Compact, low-profile package, diodes, NMX Series power supplies can only 12” x 8” x 3.38” easily be configured as multiple-output, • DC power good and AC power fail current-sharing, redundant power sys- signals tems. NMX Series switching power sup- • True remote inhibit plies have power factor correction, 1000- watt multiple output, and current sharing. They are available as low-profile, self- cooled modules, and are designed to meet global requirements. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com 1000 WATTS 12”x 8”x 3.38” NMX-1000 NMX-1000 10.4 lbs - 4.7 kgs Dimensions: Inches Millimeters SPECIFICATIONS: ALL MODELS Reverse Voltage: Protected against reverse voltage up to supply current rating. Cooling: Self cooled with internal ball-bearing fans. Consult factory for alternative INPUT configurations. AC Input: 90-264 Vac continuous range, 47 to 63 Hz. Internally fused for 20 A. Power Factor: 0.99 typical at full load. Meets EN61000-3-2. OPTIONS: Inrush: Cold start AC current is less than 90 A at 115 Vac and 180 A at 230 Vac. Limited by thermistor. Consult factory for available options. Brownout Protection: Holds regulation to 85 Vac. Holdup Time: 20 ms minimum after removal of power at full load. Efficiency: 75% typical. AC Power Fail: Provides TTL “0” 5 ms before output voltage goes out of regulation band AC INPUT (90-264 VAC Continuous Range) upon loss of AC power. FUNCTION 115 VAC 230 VAC CONNECTOR OUTPUT TB1- (L) Line Line 1 Barrier strip Adjustability: All outputs user adjustable ±5% minimum. Outputs #2 and 3 have factory TB1- (N) Neutral Line 2 # 6-32 screws adjustable preprogrammed slope. 3/8” centers Line & Load Reg: Outputs #1 and 4 hold ±1% over AC input range and 0 to 100% load TB1- ( ) Safety Ground Safety Ground change. Outputs #2 and 3 hold ±2% (preprogrammed slope). Output #1 requires minimum load of 10%. DC OUTPUT Ripple & Noise: Less than 1% p-p or 100 mV, whichever is greater. FUNCTION LOCATION NOTES CONNECTOR Remote Sense (Outputs #1, 2, and 3): Compensates for 250 mV total line drop. Open sense Output #1 Terminal marked +V Main output lead protection. Studs # 5/16-18 x 1” Temperature Coefficient: 0.02% per degree C. Terminal marked -V Rtn (Common) Stability: 0.1% over 8 hours after 30 minutes warm-up. Output #2 J2-1, 2, 3 Transient Response (Output #1): Output voltage returns to within 1% in less than 500 µs for J2-4, 5, 6 Rtn (Common) AMP # 350830-1 a 50% load change. Peak transient does not exceed 5%. mates with plug Overload Protection: All outputs are protected against overload and short circuit. Automatic Output #3 J2-7, 8, 9 recovery upon removal of fault. housing # 350736-1 J2-4, 5, 6 Rtn (Common) Overvoltage Protection (Outputs #1, 2, and 3): Protects load against power supply induced with pins Output #4 J2-10, 11, 12, (+) Floating Output overvoltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. J2-13, 14, 15 (-) Floating Output Peak Output Current: Dual current ratings define continuous and peak currents. The peak current shown can be delivered for a maximum period of 30 seconds. STATUS AND CONTROL Remote Inhibit: Contact closure to the negative sense line or a TTL level “0” turns off DC FUNCTION LOCATION NOTES CONNECTOR outputs. DC Power Good: Provides a TTL “1” when output #1 is above 4.6 V nominal. Remote Sense J3-1 Output #1 Sense Redundancy: External OR-ing diodes and current sharing on outputs #1, 2, and 3 provide J3-3 Output #1 Sense Rtn “N+1” capability. Remote senses compensate for additional 0.6 V diode voltage drop. J3-8 Output #2 Sense When the forced current sharing terminal is connected among units, current sharing remains within 10% of the unit’s full output current rating. AMP MTA type J3-7 Output #2&3Sense Rtn #640456-9 pin ENVIRONMENTAL J3-9 Output #3 Sense header (locking) Thermal Protection: Shuts down power supply if overheated. Automatic recovery. DC Power Good J3-6 Reference to Common Temperature Range: 0° to 50°C at full ratings. when a Sense Rtn is AC Power Fail J3-4 Safety Agencies: Most models are approved to UL1950; CSA 22.2 #234; IEC 950 and TÜV terminated EN60950, Class 1 SELV., CE 72/23/EEC/93/68EEC (low voltage directive). Inhibit J3-5 Conducted RFI: Meets FCC Part 15, Subpart J, Class A; EN55022 Class B; CISPR 22 Class B. Current Share J3-2 Output Isolation: Isolated from ground 50 Vdc. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com