SL POWER TMX-353-0512

350 WATTS MULTIPLE OUTPUT 48 VDC INPUT, HOT SWAP TMX-350 Featuring: STANDARD TMX SERIES • Diode isolated outputs for hot swap MODEL PWR OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 • “Zero wire” slope program current TMX-353-0512 350 +5V @ 50A +12V @ 8/12A pk -12V @ 4A sharing TMX-354-1205 350 +5V @ 50A +12V @ 8/12A pk -12V @ 4A 5.2V @ 5A TMX-354-1212 350 +5V @ 50A +12V @ 8/12A pk -12V @ 4A 12V @ 5A • Self-aligning connector with solid TMX-354-1224 350 +5V @ 50A +12V @ 8/12A pk -12V @ 4A 24V @ 3A metal, machined contacts TMX-354-1512 350 +5V @ 50A +15V @ 4A -15V @ 4A 12V @ 5A • Identical output performance as TMX-354-1524 350 +5V @ 50A +15V @ 4A -15V @ 4A 24V @ 3A RMX-350 Series Maximum power from outputs #2, #3 and #4 to be less than 170W • Dual converter design eliminates interaction between logic and TMX Series power supplies are auxiliary outputs designed to meet applicable Bellcore • Low ripple and noise on all outputs and NEBS standards, so they are • DC power good signal readily operated from Central Office power (48 Vdc). They are DC clones • True remote inhibit of Condor’s RMX Series power • Monotonic turn-on and turn-off supplies. The RMX and TMX power supplies are directly interchangeable. They allow you to operate existing systems from AC or DC power with- out compromising performance or making any mechanical changes for mounting or cooling. TMX and RMX Series power supplies can also be operated in redundant configurations to achieve AC operation with battery backup capability. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com SEE RMX 350 FORACINPUT EQUIVALENT 350 WATTS 10.75”x 4.8”x 2.5” TMX-350 TMX-350 3.8 lbs - 1.7 kgs Dimensions: Inches Millimeters SPECIFICATIONS: ALL MODELS OPTIONS INPUT Consult factory for available options. DC Input: 40-60 Vdc. Internally fused for 15 A. Efficiency: 75% typical. Low Input Provides TTL “0” when input is below 40 Vdc. DC INPUT OUTPUT FUNCTION 48 Vdc CONNECTOR Adjustability: Outputs #1 and 2, and 4 factory adjusted to nominal ±0.2%. Output #3 tracks J1-22 +48 Vdc #2; initial accuracy ±3%. See below Line & Load Reg: Outputs #1, 2, and 4 hold ±2% (with local sense) over dc input range and 0 J1-24 -48 Vdc to 100% load change (preprogrammed slope). Output #3 requires 20% minimum load on J1-11 Safety Ground outputs #2 and 3 to hold ±5%. Ripple & Noise: 1% p-p or 100 mV, whichever is greater. DC OUTPUT Remote Sense (Output #1): Compensates for 250 mV total line drop. Preprogrammed slope remains under ±3% worst case. Open sense lead protection. FUNCTION LOCATION NOTES CONNECTOR Temperature Coefficient (Outputs #1, 2, and 4): 0.03% per degree C. Output #1 J1- 10, 20, 30 Main Output Stability: 0.1% over 8 hours after 30 minutes warm-up. Positronics # Transient Response (Outputs #1, 2, and 4): Output voltage returns to within 1% in less than J1 - 9, 19, 29 Rtn (Common) PLC30M400A1-168.3 500 µs for a 50% load change (measured with rise time and fall time of 200 µs). Peak Output #2 J1-2 Mates with panel transient does not exceed 5%. J1-3 Rtn (Common) Overload Protection: All outputs are protected against overload and short circuit. Automatic mounted recovery upon removal of fault. PLC30F1000 Output #3 J1-4 Overvoltage Protection (Outputs #1 and 2): Protects load against power supply induced over- connector using J1-3 Rtn (Common) voltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. crimp contacts Peak Output Current: Dual current ratings define continuous and peak currents. The peak Output #4 J1-5 (+) Floating FC114N2 current shown can be delivered for a maximum period of 30 seconds. Output (14 to 16 AWG) Remote Inhibit: Contact closure to the negative sense line or a TTL level “0” turns off DC J1-6 (–) Floating outputs. Output Redundancy: Built-in OR-ing diodes, slope program current sharing on all outputs, and self aligning connector provide “hot swap” and “N+1” capabilities. Current sharing remains within 10% of the unit’s full output rating while units are in thermal equilibrium. STATUS AND CONTROL Remote Enable: Contact closure to common turns on DC outputs (recessed pin for “make FUNCTION LOCATION NOTES CONNECTOR last, break first” connection). DC Power Good: Provides a TTL “1” open collector when output #1 is above 4.6 V nominal. Remote Sense J1-18 Output #1 Sense Reverse Voltage: Protected against reverse voltage up to supply current rating. J1-8 Output #1 Sense Rtn ENVIRONMENTAL DC Power Good J1-7 Reference to Common Thermal Protection: Shuts down power supply if overheated. Automatic recovery. when #1 Sense Rtn Holdup Time: 20 ms minimum after removal of power at full load. See above is terminated Temperature Range: 0° to 50°C at full ratings. Safety Agencies: Most models are approved to UL1950; CSA 22.2 #234; IEC 950 and TÜV Enable J1-16 Reference EN60950, Class 1 SELV., CE 72/23/EEC/93/68EEC (low voltage directive). to Common Conducted RFI: Meets FCC Part 15, Subpart J, Class A; EN55022 Class B and CISPR 22 Class B. Inhibit J1-27 Cooling: Self-cooled by internal ball-bearing fan. Battery Low J1-17 Output Isolation: Isolated from ground 50 Vdc. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com