Automotive Relays Plug-in Maxi ISO Relays Shrouded Power Relay F7 A ■ Pin assignment similar to ISO 7588 part 1 ■ Customized versions on request – Integrated components (e.g. resistor, diode) – Customized marking/color – Special cover with bracket Typical applications Cross carline up to 70A for example: ABS control, blower fans, cooling fan, energy management, engine control, fuel pump, heated front screen, ignition, lamps: front, rear, fog light, main switch/supply relay, wiper control. F136_fcw1_bw Contact Data Contact Data (continued) 6 Contact arrangement 1 form A, 1 NO Mechanical endurance >1x10 ops. Rated voltage 12VDC 1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current Limiting continuous current duration of maximum 3s for a make/break ratio of 1:10. 23°C 70A 2) Current and time are compatible with circuit protection by a typical automotive fuse. 85°C 50A Relay will make, carry and break the specified current. 125°C 30A 3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at 1) Limiting making current 240A http://relays.te.com/appnotes/ Limiting breaking current 70A 4) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion Limiting short-time current and/or higher risk of contact tack welding. 2) overload current, ISO 8820-3 1.35 x 50A, 1800s 2.00 x 50A, 5s 3.50 x 50A, 0.5s Coil Data 6.00 x 50A, 0.1s Rated coil voltage 12VDC Jump start test, ISO 16750-1 24VDC for 5min, conducting nominal current at 23°C Coil versions, DC coil Contact material Silver based Coil Rated Operate Release Coil Rated coil 3) 5) 5) Min. recommended contact load 1A at 5VDC code voltage voltage voltage resistance power Initial voltage drop at 10A, VDC VDC VDC Ω±10% W form A (NO) contact, typ./max. 15/200mV 004 12 7.2 1.6 90 1.6 Frequency of operation at nominal load 6 ops./min (0.1Hz) 5) Without components in parallel. 4) Operate/release time typ. 7/2ms All figures are given for coil without pre-energization, at ambient temperature +23°C. 5 Electrical endurance >2x10 ops. resistive load, NO contact 50A, 14VDC Max. DC load breaking capacity Coil operating range ECR0629-N 136J_OVR2 30 Umax 25 20 15 Does not take into account the temperature rise due to Uop (E = 13,5 V) the contact current 10 E = pre-energization Uop = operate voltage Uop (E = 0 V) 5 0 -4 0-20 02 04 06 08 01 00 12 0 Ambient temperature in °C Load limit curve 1: arc extinguishes during transit time (changeover contact). Does not take into account the temperature rise due to the contact current Load limit curve 2: safe shutdown, no stationary arc (make contact). E = pre-energization. Load limit curves measured with low inductive resistors verified for 1000 switching events. 1 02-2017, Rev. 0217 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2017 TE Connectivity. together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. http://relays.te.com/definitions Coil voltage in V Automotive Relays Plug-in Maxi ISO Relays Shrouded Power Relay F7 A (Continued) Insulation Data Other Data (continued) Initial dielectric strength Terminal type plug-in, QC between open contacts 500V Cover retention rms between contact and coil 500V pull force 150N rms between adjacent contacts 500V push force 200N rms Load dump test Terminal retention ISO 7637-1 (12VDC), test pulse 5 V =+86.5VDC pull force 150N s ISO 7637-2 (24VDC), test pulse 5 V =+200VDC push force 150N s Weight approx. 60g (2.1oz) Packaging unit 108 pcs. 6) Refers to used materials. Other Data 7) No change in the switch.ing state >10μs. Valid for NC contacts, NO contact values EU RoHS/ELV compliance compliant significantly higher. 6) Protection to heat and fire according UL94 HB or better Ambient temperature -40 to 125°C Climatic cycling with condensation, Accessories EN ISO 6988 6 cycles, storage 8/16h For fitting connectors please contact us via online Support Center Temperature cycling, IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min) Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C Damp heat constant, IEC 60068-2-3, Ca 56 days Category of environmental protection, IEC 61810 RT III – sealed Degree of protection, IEC 60529 IP67 (sealed) only with special connector Vibration resistance (functional) 7) IEC 60068-2-6 (sine sweep) 10 to 500Hz, min. 10g Shock resistance (functional) 7) IEC 60068-2-27 (half sine) 6ms, min. 30g Drop test, free fall, IEC 60068-2-32 1m onto concrete Terminal Assignment NOR 1 form A, NO with resistor 2 5 1 3 2 02-2017, Rev. 0217 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2017 TE Connectivity. together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. http://relays.te.com/definitions Automotive Relays Plug-in Maxi ISO Relays Shrouded Power Relay F7 A (Continued) Dimensions 24 0,5 54,2 TE136J_DD2 TE136_DD5 View of the terminals (bottom view) 10,9 0,5 TE136J_DD1 32,4 TE136J_VT1 5,5 TE136J_VT1 TE136_BV1 Product code structure Typical product code V23136 -J 1 004 -X050 Type V23136 Power Relay F7 A Contact arrangement J 1 form A, 1 NO Cover 1 Bracket at terminal 3 Coil 004 12VDC Terminal/arrangement Xnnn Customized (nnn: version number) 1) Product code Arrangement Cover Coil suppr. Circuit Coil Contact material Terminals Part number V23136-J1004-X050 1 Form A, 1 NO Standard Resistor 560Ω NOR 12VDC Silver based Plug-in, QC 1-1414122-0 1) See terminal assignment diagrams. Other types on request. This list represents the most common types and does not show all variants covered by this datasheet. 3 02-2017, Rev. 0217 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2017 TE Connectivity. together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. http://relays.te.com/definitions 30 39,6 6,7 3,2 0,1 35,2 4,6 0,5 6,4 0,5