420 W 200 W 100 W 30 W Automotive Relays PCB Single Relays Micro Relay K (THT – THR) ■ Small power relay ■ Limiting continuous current 20A at 85°C ■ Low weight ■ Low noise operation ■ Wave (THT) and reflow (THR/pin-in-paste) solderable versions ■ For double version refer to Double Micro Relay K Typical applications Door lock, heated front/rear screen, lamps front/rear/fog light, interior lights, seat control, sun roof, window lifter, wiper control. 086C/R1_fcw1b Contact Data Typical applications Inductive load Wiper load Resistive/inductive load Lamp load V23086-*1*01-A403 V23086-*1*02-A803 V23086-*1*01-A402 V23086-*1*51-A502 Contact arrangement 1 form C, 1 CO 1 form C, 1 CO 1 form A, 1 NO 1 form A, 1 NO Rated voltage 12VDC 10VDC 12VDC 10VDC NO/NC NO/NC 1) Rated current 30/25A 30/25A 30A 15A 1) Limiting continuous current 23°C 30/25A 30/25A 30A 15A 85°C 20/15A 20/15A 20A 10A 105°C 15/10A 15/10A 15A 2) 2) 2) 3) Limiting making current 40A 40A 40A 100A Limiting breaking current 30A 30A 30A 30A Contact material AgSnO 2 4) Min. contact load >1A at 5VDC Initial voltage drop at 10A, typ./max. 30/300mV 5) Operate/release time typ. 3/1.5ms Electrical enduranc cyclic temperature -40°C, +25°C, +85°C form C contact (CO) at 14VDC motor reverse blocked, wiper, 25A, 0.77mH 25A make/5A break, 5 >1x10 ops. generator peak, 20A on NC,1mH 6 >1x10 ops. form A contact (NO) at 14VDC resistive 20A lamp 100A inrush, 5 >1x10 ops. 10A steady state 5 >1x10 ops. 6 Mechanical endurance >5x10 ops. 2 1) Measured on 70x70x1.5mm epoxy PCB FR4 with 25cm (double layer 105μm) Max. DC load breaking capacity 2 copper area. Connecting cable cross section 6 mm .Boundary conditions: 180°C coil temperature;130°C solder joint. 100 2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) Corresponds to the peak inrush current on initial actuation (cold filament). 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ 5) Measured at nominal voltage without coil suppression unit. A low resistive suppression device in parallel to the relay coil increases the release time and reducesthe lifetime caused by increased erosion and/or higher risk of contact tack welding. curve I curve II 10 0.11 10 100 Switching Current in A Load limit curve 1: arc extinguishes, during transit time (changeover contact). Load limit curve 2: safe shutdown, no stationary arc (make contact). Load limit curves measured with low inductive resistors verified for 1000 switching events. 1 07-2017, Rev. 0717 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2017 TE Connectivity. together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. http://relays.te.com/definitions Max. Switching Voltage in VDC Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Coil Data Other Data Rated coil voltage 12VDC EU RoHS/ELV compliance compliant Ambient temperature, DC coil -40 to +105°C Coil versions, DC coil Cold storage, IEC 60068-2-1 1000h; -40°C Coil Rated Operate Release Coil Rated coil Dry heat, IEC 60068-2-2 1000h; +125°C code voltage voltage voltage resistance power Climatic cycling with condensation, VDC VDC VDC Ω±10% mW EN ISO 6988 20 cycles, storage 8/16h 001/801 12 6.9 1.5 254 0567 Temperature cycling (shock), 002/802 10 5.7 1.25 181 0552 IEC 60068-2-14, Na 100 cycles; -40/+125°C 051/851 10 6.5 1.1 90 1111 Temperature cycling, All figures are given for coil without pre-energization, at ambient temperature +23°C. IEC 60068-2-14, Nb 35 cycles; -40/+125°C Damp heat cyclic, Coil operating range IEC 60068-2-30, Db, variant 1 6 cycles 25°C/55°C/93%RH Damp heat constant, 300 IEC 60068-2-3 method Ca 56 days 40°C/95%RH Degree of protection 250 Umax THT: RT III (61810) THR: RT II (61810) 200 Sealing test, IEC 60068-2-17: THT Qc, method 2, 1min, 70°C Corrosive gas 150 IEC 60068-2-42 10 days IEC 60068-2-43 10 days 100 Vibration resistance (functional) 6) IEC 60068-2-6 (sine sweep) 10 to 500Hz; 6g 50 Uop (E=0V) Shock resistance (functional) 6) IEC 60068-2-27 (half sine) 6ms, up to 30g 0 -40-20 020406080100 120 Terminal type PCB:THT, THR Ambient temperature in °C Weight approx. 4g (0.14oz) Does not take into account the temperature rise due to the contact current Solderability (aging 3: 4h/155°C) THT E = pre-energization IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C Solderability THR IEC60068-2-58 hot dip 5s 245°C Insulation Data Resistance to soldering heat THT Initial dielectric strength IEC 60068-2-20 Tb, method 1A, hot dip 10s, between open contacts 500VAC 260°C with thermal screen rms between contact and coil 500VAC Resistance to soldering heat THR rms IEC 60068-2-58 260°C; preheating min 130°C 7) Storage conditions according IEC 60068-1 Packaging unit 2000 pcs. 6) Depending on mounting position: no change in the switching state >10μs. 7) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ 2 07-2017, Rev. 0717 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2017 TE Connectivity. together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. http://relays.te.com/definitions Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Terminal Assignment Mounting Hole Layout Bottom view on solder pins Bottom view on solder pins 1 form A, 1 NO 1 form C, 1 CO 4 4 3 1 5 1 5 8.5 C 7.5 2 2 0.5 B 86ets_ab 86etw_ab 1.72 3 4 5 1 Dimensions 2 Micro Relay K, THT version 5 x 5 x 0.4 A B C ± 0.2 0.4 A 12.0 0.3 A 0.3 A TE86etw_an1 5.8 ± 0.1 2.5 ± 0.2 Remark: Positional tolerances according to DIN EN ISO 5458 0.6 ± 0.2 A 12.9 ± 0.3 0.95 ± 0.2 TE86etw_se *) Additional tin tops max. 1 mm *) Additional tin tops max. 1mm 3 07-2017, Rev. 0717 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2017 TE Connectivity. together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. http://relays.te.com/definitions +0.05 3x 1.2 0 ± 0.1 0.4 7.65 ± 0.1 2.8 ± 0.2 *) ± 0.2 9.9 +0.05 0.5 2 x 0 1.38 3.0 3.6 10.2 Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Micro Relay K, THR version Mounting Hole Layout Bottom view on solder pins 86R1_DD2_2 86R1_VT3 View of Stand-Offs Bottom view on solder pins 86R1_DD1_2 86R1_VT1 *) Additional tin tops max. 1mm 4 07-2017, Rev. 0717 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2017 TE Connectivity. together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. http://relays.te.com/definitions *) Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Product code structure Typical product code V23086 -C 1 001 -A 4 03 Type V23086 Micro Relay K (THT – THR) Terminal and enclosure C PCB version THT, sealed R PCB version THR, vented Design 1 Single relay Coil 001 Standard (THT) 002 Sensitive (THT) 801 Standard (THR) 802 Sensitive (THR) 051 Lamp load (THT) 851 Lamp load (THR) Contact type A Single contact Contact material index 4 AgSnO standard 8 AgSnO wiper load 2 2 5 AgSnO lamp load 2 Contact arrangement index 02 NO 03 CO Product code Version Design Coil Contact Cont. material Arrangement Part number V23086-C1001-A402 PCB THT, Single Standard Single AgSnO (standard) 1 form A, 1 NO 0-1393280-5 2 V23086-C1001-A403 cleanable 1 form C, 1 CO 0-1393280-6 V23086-C1051-A502 Lamp load AgSnO (lamp) 1 form A, 1 NO 2-1904093-1 2 V23086-C1002-A803 Sensitive AgSnO (wiper) 1 form C, 1 CO 2-1414987-3 2 V23086-R1801-A402 PCB THR, Standard AgSnO (standard) 1 form A, 1 NO 2-1904093-2 2 V23086-R1801-A403 vented 1 form C, 1 CO 6-1414920-0 V23086-R1851-A502 Lamp load AgSnO (lamp) 1 form A, 1 NO 9-1904064-4 2 V23086-R1802-A803 Sensitive AgSnO (wiper) 1 form C, 1 CO 7-1414967-8 2 This list represents the most common types and does not show all variants covered by this datasheet. Other types on request. 5 07-2017, Rev. 0717 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2017 TE Connectivity. together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. http://relays.te.com/definitions