12mm Rotary Encoder with LED Type DPL12 Series Key Features 12mm rotary encoder Incremental type Push switch option Various shaft lengths LED color options Detent 12mm rotary incremental encoder with LED for use in electronic equipment. Options Can be supplied with or without switch with customization to standard options. Characteristics – Electrical Pulse 24 / 360° Contact Rating 0.5mA 5VDC Dielectric Strength 300VAC / 1mA, 1 minute Insulation Resistance (min) ���MΩ at �5�VAC Operating Speed (RPM) 60 RPM Electrical Travel Continuous Rotational Noise t2 = 2.0ms max (see below) Chattering t1 & t3 = 3.0ms max (see below) Code off Area V=3.5V or more Code on Area V=1.5V or less LED With Switch – Dual color (see below) No Switch – Single color (see below) Color Options Switch – 1 = Blue / Green, 2 = Blue / Orange, 3 = Green / Red) No Switch – White, Red, Green, Blue Switch Power Rating (where fitted) 5VDC 10mA Switch contact Resistance ���MΩ �a�. Operating Temperature -10°C ~ +85°C Storage Temperature -40°C ~ +70°C Dimensions in Dimensions Shown for 1-1773449-0 CIS WR 11/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change 12mm Rotary Encoder with LED Electrical Characteristics Item Conditions Specifications 2 Phase different signals (signal A & signal B) Details shown below (broken line shows detent position where fitted) A (Terminal A-C) C/W Output Signal B (Terminal B-C) Format A (Terminal A-C) C C/W B (Terminal B-C) Resolution Number of pulses in 360° rotation 24 pulses / 360° each phase Switching Measurement shall be made under the following conditions: Characteristics 1. Shaft rotational speed: 360°/S 2. Test Circuit: See below Chattering Spe�ified �� the sig�al’s passage ti�e from 3.5V to 1.5V or from 1.5V to 3.5V of each switching position (Code OFF → ON or ON →OFF t₁ , t₃ �3mS NB To a�oid �hatteri�g �t₁- t₃� please consider masking time and adding C/R filters to your circuit for pulse count design. Sliding Noise Bounce Specified by the time of voltage change exceed 1.5V in code ON area. When the bounce has code ON time less than 1mS �et�ee� �hatteri�gs �t₁ or t₃� the T� ≤��S voltage change shall be regarded as part of chattering, When the code ON time between two bounces is less than 1ms they are regarded as one linked bounce Dimensions in Dimensions Shown for 1-1773449-0 CIS WR 11/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change 12mm Rotary Encoder with LED Sliding Noise Sliding Noise (continued) The voltage change in OFF area 3.5V min. �t₁ , t₃� Maski�g ti�e to a�oid �hatteri�g Code OFF area – The area in which the voltage is 3.5V or more Code ON area – The area in which the voltage is 1.5V or less Measurement shall be made in the condition in which the shaft is rotated in 360° / S (constant speed) Rotational direction ΔT � 3.5msec Phase Difference Rotatio�al Dire�tio� → Note: The test is conducted using equipment at constant speed 360°/ S according to spec. The test result could be different under manual conditions. In order to prove the interoperability between the firmware and the encoder please test the part in real conditions Insulation Measurement shall be made under the Between individual terminals Resistance condition which a voltage of 250V D.C and attaching Plate:���MΩ is applied between individual terminals MIN and attaching plate Dielectric A voltage of 300V A.C. shall be applied Without arcing or breakdown Strength for 1 min or a voltage of 360 VA.C. shall be applied for 2 sec between individual terminals and attaching plate ( Leak current : 1mA ) Number and 24 detents position of Step angle: 15°±3° detents Terminal Push and pull static load of 5Kgf shall Without damage to. or Strength be applied to the shaft in the axial excessive play in shaft .No direction for 10sec .( After soldering of excessive abnormality in the PC board ) rotational feeling and electrical characteristies shall be satisfied. Rotation play at Measure with jig for rotational angle 4°Max the click position Dimensions in Dimensions Shown for 1-1773449-0 CIS WR 11/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change 12mm Rotary Encoder with LED Endurance Characteristics Item Conditions Specification Rotational Life The shaft of the encoder shall be rotated Chattering: t1,t3�5ms to 30,000 cycles at a speed of 600 ~ 1000 Bounce: t2�3ms cycles per hour without electrical load, Phase- after which measurement shall be made difference:△T�2.5msec (1 cycle： rotate 360°C.C.W. rotate 360° Where applicable detent C.W.) feeling remains. All electrical specification shall be met Soldering Condition Item Conditions Specifications Hand Soldering Bit temperature: 350°C or less There shall be no Dwell time: 3S max. deformation or cracks in molded part. No excessive Dip soldering Preheating: abnormality in rotational PCB surface temp: 100°C or less feeling Preheating time: 2 minutes Max. Soldering: Solder temperature: 260°C±5°C Immersion time: 5±1S 2 times max. Switch Electrical Characteristics (Where fitted) Item Conditions Specification Contact Measured by the electric current D.C. ��� �Ω MAX resistance voltage drop method Chattering Switch is operated at the rate of 1 cycle 1 Less than 10 msec sec. The 1 cycle shall be OFF - ON - OFF Insulation Measurement shall be made under the Between individual terminals Resistance condition which a voltage of 250V D.C. is and attaching plate. applied between individual terminals and ���MΩ MIN . attaching plate. Dielectric A voltage of 300V A.C. shall be applied for Without damage to parts Strength 1 min. or a voltage of 360V A.C. shall be arcing or breakdown. applied for 2 sec between individual terminals and attaching plate. ( Leak current : 1mA ) Switch rating D.C.5V 10mA (Resistor load) Note Shaft is insulated from switch terminal Switch Mechanical Characteristics (Where fitted) Item Conditions Specification Contact S.P.S.T Push On arrangement Switching 0.5+0/-0.3mm stroke Dimensions in Dimensions Shown for 1-1773449-0 CIS WR 11/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change 12mm Rotary Encoder with LED Switch Mechanical Characteristics (Continued) Item Conditions Specification Switch strength 450 ± 200gf Switch Endurance Characteristics Item Conditions Specification Operating life The shaft of switch shall be operated Switch contact resistance : 20,000 times without electronic load, ����Ω MAX after which measurements shall be made Switch strength: Relative to the previously Specified value +10% / -30%. Except above items specification as shown above LED Common Specifications Single color (No Switch) Circuit LED Characteristics Reverse Voltage: 5V Test Conditions IF = 20mA Power DC Forward Emitted Colour Dissipation Current Forward Voltage (V) Typ. Max. Red 60mW 30mA 1.8 2.6 Lawn Green 100mW 30mA 2 2.6 Blue 72mW 20mA 3.2 3.6 Orange 100mW 30mA 2.1 2.6 White 72mW 20mA 3.2 3.6 Green 72mW 20mA 3.2 3.6 Dark Orange 100mW 30mA 2.1 2.6 Dimensions in Dimensions Shown for 1-1773449-0 CIS WR 11/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change 12mm Rotary Encoder with LED LED Common Specifications Dual color (Switch) Circuit LED Characteristics Reverse Voltage: 5V Test Conditions DC Power IF = 20mA Forward Emitted Colour Dissipation Current Forward Voltage (V) (mW) (mA) Min. Typ. Max. Blue / Blue 75 20 2.7 3.3 3.7 Orange Orange 60 25 1.7 2 2.4 Green / Green 95 25 2.7 3.3 3.7 Red Red 60 25 1.7 2 2.4 Blue / Blue 75 20 2.7 3.3 3.7 Green Green 95 25 2.7 3.3 3.7 Red / Red 60 25 1.7 2 2.4 Green Green 95 25 2.7 3.3 3.7 Green / Green 95 25 2.7 3.3 3.7 Orange Orange 60 25 1.7 2 2.4 Blue / Blue 75 20 2.7 -- 3.3 Red Red 60 25 1.7 -- 2.4 White / White 75 20 2.7 -- 3.7 Red Red 60 25 1.75 -- 2.35 White / White 75 20 2.7 -- 3.7 Green Green 60 25 1.7 -- 2.4 Dimensions DPL12V Dimensions in Dimensions Shown for 1-1773449-0 CIS WR 11/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change 12mm Rotary Encoder with LED Dimensions DPL12H Dimensions DPL12SV Dimensions DPL12SH Dimensions in Dimensions Shown for 1-1773449-0 CIS WR 11/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change 12mm Rotary Encoder with LED Shaft Length – Without Switch Type Dim Options (mm) K L (from mounting surface) 24 only L (from mounting surface) 17.5 20 25 F F 5 7 12 Shaft Length – With Switch Type Dim Options (mm) K L (from mounting surface) 25 only L (from mounting surface) 18.5 21 26 F F 5 7 12 LED Color Codes Switch Option Code Description 1 Blue / Green 2 Blue / Orange 3 Green / Red Switch 4 Red / Green (Dual Color) 5 Green / Orange 6 Blue / Red 7 White / Red 8 White / Green R Red L Lawn Green B Blue No Switch O Orange (Single Color) W White G Green D Dark Orange How To Order DPL12 V N 24 A 20 F R Common Orientation Detent Pulses Bush Shaft Shaft LED Part Length Style Color DPL12 – V – Vertical N – 24 – 5mm See F – See No H - None 24 relevant Flatted relevant Switch Horizontal 24 – pulses table K - table DPL12S – 24 Knurled Switch clicks Dimensions in Dimensions Shown for 1-1773449-0 CIS WR 11/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change