Automotive Relays PCB Single Relays Power Relay K-S n Very low voltage drop n Wide voltage range Typical applications ABS control, blower fans, cooling fan, engine control, glow plug, heated rear screen, ignition, main switch/supply relay, preheating system, valves, wiper control. C071S_fcw1b Contact Data 12VDC 24VDC Coil Data 6) Contact arrangement 1 form A, 1 NO Rated coil voltage 12VDC, 24VDC Rated voltage 12VDC 24VDC 6) Other nominal voltages available on request. Rated current 70A Limiting continuous current Coil versions, DC coil 23°C 70A Coil Rated Operate Release Coil Rated coil 85°C 50A code voltage voltage voltage resistance power 1)2) 1)2) Limiting making current 300A 150A VDC VDC VDC Ω±10% W 1) 1) Limiting breaking current 70A 35A 009 12 6.9 1.2 64 2.3 Contact material AgNi0.15 010 24 14.1 2.4 234 2.5 3) All figures are given for coil without pre-energization, at ambient temperature +23°C. Min. recommended contact load 1A at 5VDC Initial voltage drop at 10A, typ./max. 10/300mV 4) Frequency of operation 20 ops./s Coil operating range 5) Operate/release time max. typ. 4/3ms Electrical endurance 4 5 resistive load, >5x10 ops. >1x10 ops. at 13.5VDC, 50A at 27.5VDC, 15A 6 Mechanical endurance >10 ops. Max. DC load breaking capacity Does not take into account the temperature rise due to the contact current E = pre-energization. Insulation Data Initial dielectric strength between contact and coil 500VACrms Max. DC load breaking curve: safe shutdown, no stationary arc. Load limit curves measured with low inductive resistors verified for 1000 switching events. 1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages. 2) For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ 4) With load the values depend on PCB layer design and max. environmental temperature. 5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding (monostable version only). 1 11-2011, Rev. 1111 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions Automotive Relays PCB Single Relays Power Relay K-S (Continued) Other Data Terminal Assignment EU RoHS/ELV compliance compliant Bottom view on solder pins 6) Ambient temperature -40 to +85°C Category of environmental protection, IEC 61810 RT II – fluxproof 1 form A, 1 NO Vibration resistance (functional) IEC 68-2-6 (sine pulse form), 10 to 200Hz 20 to 40g no change in the switching state >10μs Shock resistance (functional) IEC 68-2-27 (half sine form single pulses), 8ms 30g open form A (NO) contact will not close >10μs Terminal type PCB Weight approx. 19g (0.68oz) Resistance to soldering heat THT TE0606-J1 IEC 60068-2-20, Tb, method 1A, 10s+/-1s with shielding Note: 7) Storage conditions according IEC 60068 Check polarity and frame connection (ground) Packaging unit 400 pcs. * For mounting only, not for electrical connection. 6) See graph: coil operating range. 7) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ Dimensions PCB Layout Bottom view on solder pins 18.85 ±0.05 13.0 ±0.05 18.6 ±0.65 8.8 ±0.05 24.2 ±0.8 ø 2.3 +0.1 2.85 ±0.05 2.2 ±0.1 1.1 +0.05 0.45 18.0 ±0.5 5.4 1.0 +0.05 ø 1.3 +0.1 ø 2.5 +0.1 12.1 +0.1 ø 2.1 +0.1 3.0 ±0.5 *) 2.5 – 3.0 ø 2.3 +0.1 ø 2.3 +0.1 1.0 +0.05 Terminals tinned *) additional tin tops 5.1 ±0.05 TE2184-52 max. 1.5 mm TE0594-R2 16.1 ±0.05 Product code structure Typical product code V23071 -A 1 009 -A 13 2 Type V23071 Power Relay K-S Terminal and enclosure A PCB, open (RT II) Design 1 Single relay Coil 009 12VDC 010 24VDC Contact type A Single contact Contact material 13 AgNi0.15 Contact arrangement 2 1 form A, 1 NO Product code Terminal/Encl. Design Coil Contact type Cont. material Arrangement Part number V23071-A1009-A132 PCB, open Single relay 12 VDC Single contact AgNi0.15 1 form A, 1 NO 1393276-3 V23071-A1010-A132 24 VDC 1393276-7 2 11-2011, Rev. 1111 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions