PCB Relays Catalog 1308028-2 Revised 8-2008 Single Relays Micro Relay K SMD (Standard – Open Vent Hole) Features – Small power relay for surface mounted technology – Limiting continuous current 30 A – Minimal weight – Low noise operation – Relay designed for convection and infrared reflow soldering – Standard SMD and SMD with open vent hole versions – For twin version refer to Double Micro Relay K SMD – For latching (bistable) version refer to Micro Relay K Latching – For through hole technology refer to Micro Relay K Typical Applications – Car alarm – Door control – Door lock – Hazard warning signal – Immobilizer – Interior lights – Seat control – Sun roof – Window lifter – Wiper control 86M1_3D1 Please contact Tyco Electronics for relay application support. Design Terminals Conditions – ELV/RoHS/WEEE compliant SMD terminals for assembly on All parametric, environmental and – SMD (standard): sealed type printed circuit boards endurance tests are performed washable according to EIA Standard RS-407-A – SMD (open vent hole): sealed at standard test conditions unless type open vent hole otherwise noted: 23°C ambient temperature, Weight 20 - 50% RH, 998.9 ±33.9 hPa. Approx. 4 g (0.14 oz.) For general storage and processing Nominal Voltage recommendations please refer to our 12 V Application Notes and especially to Storage in the “Glossary” page 23 or at http://relays.tycoelectronics.com/ appnotes/ Disclaimer All technical performance data apply to the relay as such, specific conditions of the individual application are not considered. Please always check the suitability of the relay for your intended purpose. We do not assume any responsibility or liability for not complying herewith. We recommend to complete our questionnaire and to request our technical service. Any responsibility for the application of the product remains with the customer only. All specifications are subject to change without notification. All rights of Tyco Electronics are reserved. 118 All specifications subject to change. Consult Tyco Electronics for latest specifications. PCB Relays Catalog 1308028-2 Revised 8-2008 Single Relays Micro Relay K SMD (Standard – Open Vent Hole) Dimensional Drawing 12 ± 0.2 ± 0.1 5,8 ± 0.2 2,5 ± 0.2 0,6 A TE86esw_se1 ± 0.3 12,9 ± 0.2 0,95 0.1 At terminal tip *) Dimension without soldering View of the Terminals (bottom view) +0,05 3x 1,3 0 3,06 8,5 C 1,56 0,65 B 3 4 5 4x M 0,4 A B M 0,2 A 2 1 M 0,4 A B M 0,3 A 1,5 4,06 0,4 M A C +0,05 M 0,2 A 4x 0 2x0,8 0,4 M A C 7,5 0,2 M A 86esw_an Remark: Positional tolerances according to DIN EN ISO 5458 All specifications subject to change. Consult Tyco Electronics for latest specifications. 119 16 6,01 4,09 1,5 0,4 ± 0.1 2x *) 0,7 ± 0.1 3x *) 1,5 3,36 3,06 7,65 ± 0.1 1,8 ± 0.2 11,3 ± 0.2 PCB Relays Catalog 1308028-2 Revised 8-2008 Single Relays Micro Relay K SMD (Standard – Open Vent Hole) Contact Data Typical areas of application Resistive/inductive load Contact configuration 1 Changeover contact/ 1 Form C Circuit symbol 3 5 (see also Pin assignment) 4 Rated voltage 12 V Rated current NC/NO 15 A/20 A Limiting continuous current 23°C 25 A/30 A 85°C 15 A/20 A 105°C 5 A/10 A Contact material Silver based Max. switching voltage/power See load limit curve 1) Max. switching current NC/NO 2) On 40 A Off 30 A 3) Min. recommended load 1 A at 5 V Voltage drop at 10 A (initial) for NC/NO contacts Typ. 30 mV, 300 mV max. 6 Mechanical endurance (without load) > 5 x 10 operations 4) Electrical endurance Resistive load: Wiper reverse : Motor reverse blocked: 5 5 5 at cyclic temperature –40/+23/+85°C > 3 x 10 operations > 3 x 10 operations > 1 x 10 operations and 13.5 V 20 A on NO-contact 25 A make/5 A break; 25 A generator peak - 10 A L = 0.77 mH inductive load L = 1.0 mH 1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5 V for 12 V load voltages. 2) For a load current duration of maximum 3 s for a make/break ratio of 1:10. 3) See chapter Diagnostics of Relays in our Application Notes page 31 or consult the internet at http://relays.tycoelectronics.com/appnotes/ 4) Avoid using capacitive protection circuits. It will reduce lifetime. Load Limit Curve 086LLC07 ^ Load limit curve 1 = arc extinguishes during transit time ^ Load limit curve 2 = safe shutdown, no stationary arc 120 All specifications subject to change. Consult Tyco Electronics for latest specifications. PCB Relays Catalog 1308028-2 Revised 8-2008 Single Relays Micro Relay K SMD (Standard – Open Vent Hole) Circuit Diagram 1 Changeover contact/1 Form C 4 3 5 2 1 86esw_ab Coil Data Available for nominal voltages 10 V / 12 V Nominal power consumption of the unsuppressed coil at nominal voltage 0.64 W Test voltage winding/contact 500 VACrms 1) Maximum ambient temperature range –40 to +105°C Operate time at nominal voltage Typ. 3 ms 2) Release time at nominal voltage Typ. 1.5 ms 1) See also operating voltage range diagram. 2) For unsuppressed relay coil. Note: A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. Operating Voltage Range 086_OVR03 300 250 Umax 200 Does not take into account 150 the temperature rise due to the contact current Uop (E = Un x 1.12) 100 E = pre-energization 50 Uop (E = 0 V) 0 -40 -20 0 20 40 60 80 100 120 Ambient temperature in °C All specifications subject to change. Consult Tyco Electronics for latest specifications. 121 Coil voltage in % Unom PCB Relays Catalog 1308028-2 Revised 8-2008 Single Relays Micro Relay K SMD (Standard – Open Vent Hole) Environmental Conditions Temperature range, storage Refer to Storage in the “Glossary” catalog page 23 or http://relays.tycoelectronics.com/appnotes/ Test Relevant standard Testing as per Dimension Comments Cold storage IEC 68-2-1 1000 h –40°C Dry heat IEC 68-2-2 Ba 1000 h 125°C 1) Climatic cycling with condensation EN ISO 6988 20 cycles Storage 8/16 h Thermal change IEC 68-2-14 Nb 35 cycles –40/+125°C Thermal shock IEC 68-2-14 Na 1000 cycles –40/+125°C Dwell time 1 h Damp heat cyclic IEC 68-2-30 Db, Variant 2 6 cycles 40°C/55°C/93% constant IEC 68-2-3 Method Ca 56 days 40°C/93% 1) Corrosive gas IEC 68-2-42 10 days IEC 68-2-43 10 days Vibration resistance IEC 68-2-6 (sine pulse form) 10 - 500 Hz No change in the switching state > 10 μs, 6 g Shock resistance IEC 68-2-27 (half sine single form pulses) 6 ms No change in the switching state > 10 μs up to 30 g Solderability IEC 68-2-58 Hot dip 5 s Aging 3 (4 h/155°C) 245°C for leaded process (Tm = 183°C) for Pb-free process (Tm = 217°C) Resistance to soldering heat IEC 68-2-58 Hot dip 10 s with thermal screen 260°C Preheating min 130°C Sealing IEC 68-2-17 Qc, Method 2 1 min/70°C 1) Not applicable for SMD with open vent hole. Ordering Information Part Numbers (see table below for coil data) Contact Contact Enclosure Terminals/ Relay Description Part Number Arrangement Material Soldering Technology V23086-M1011-A403 0-1393281-1 1 Form C Silver based Sealed Printed circuit/SMD V23086-M1012-A403 8-1416000-5 1 Form C Silver based Sealed Printed circuit/SMD V23086-U1011-A303 0-1416001-2 1 Form C Silver based Open vent hole Printed circuit/SMD V23086-U1012-A303 3-1414933-1 1 Form C Silver based Open vent hole Printed circuit/SMD Coil Versions 1) Coil Data Rated Coil Coil Resistance Must Must Allowable Overdrive for Micro K SMD Voltage ±10% Operate Voltage Release Voltage Voltage (V) (Standard – Open Vent Hole) (V) (Ω) (V) (V) at 23°C at 105°C V23086-M*011-**** 12 225 6.9 1.5 27 18 V23086-M*012-**** 10 156 5.7 1.25 22 15 V23086-U*011-**** 12 225 6.9 1.5 27 18 V23086-U*012-**** 10 156 5.7 1.25 22 15 1) Allowable overdrive is stated with no load applied and minimum coil resistance. Standard Delivery Packs (in reels) Micro Relay K SMD (Standard – Open Vent Hole): 200 pieces Note: Transportation and storage of the reels: horizontally only. 122 All specifications subject to change. Consult Tyco Electronics for latest specifications.