Instruction Sheet  MMCX Right-Angle Cable Plug 408-8627 Connectors 1408149-[ ] 01 Apr 11 Rev E Shrink Tubing MMCX Right-Angle Cable Plug Connector (OMNI-FLEX 200 Cable Only) Cap Housing Assembly Cable Ferrule Part Number Description Cable 1408149-1 MMCX Right-Angle Cable Plug Connector RG178/196 1408149-2 MMCX Right-Angle Cable Plug Connector RG316 1408149-3 MMCX Right-Angle Cable Plug Connector RD316 1408149-4 MMCX Right-Angle Cable Plug Connector OMNI-FLEX 200 Figure 1 1. INTRODUCTION 2. DESCRIPTION This instruction sheet contains the assembly Each MMCX Right-Angle Cable Plug Connector procedure for the MMCX Right-Angle Cable Plug consists of a housing assembly, a crimp ferrule, and a Connectors listed in Figure 1. These connectors are cap. See Figure 1. Also included is shrink tubing (for crimp attachment type connectors that attach to the use with OMNI-FLEX 200 cable only.) flexible cable listed in Figure 1. 3. ASSEMBLY PROCEDURE The table in Figure 2 references the crimp tooling used to apply these connectors. The table includes tool 1. Slide the crimp ferrule onto the cable. descriptions, the part number, and the crimp To avoid personal injury, be sure to use appropriate configuration for the tooling. NOTE safety equipment, including gloves, when using cable stripping tools. Part Crimp Configuration i Tool Description Number Ferrule (Hex) 2. Strip the cable according to the dimensions in PRO-CRIMPER* III Hand 354940-1 - - Figure 3. Tool Frame Crimp Die (RG178, Do NOT damage the cable braid, dielectric, or inner DANGER 2.67 [.105] RG196) conductor of the cable. STOP  Crimp Die (RG316) 3.25 [.128] 1583696-1 Crimp Die (RD316) 3.86 [.151] 3. Flare the cable braid and push the housing Crimp Die for assembly over the inner conductor (under the cable 2.67 [.105] OMNI-FLEX 200 braid). See Figure 4. Figure 2 4. Slide the crimp ferrule back over the cable braid and housing assembly until the inner conductor is Dimensions in this instruction sheet are in metric positioned in the center contact slot. See Figure 4. NOTE units [with U.S. customary units in brackets]. 5. Crimp using the tooling listed in Figure 2. See Figures are not drawn to scale. Figure 5. i  Reasons for revision can be found in Section 4. ©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. 1 of 2 All Rights Reserved PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, visit our website at www.te.com TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. LOC B *Trademark. Other logos, product and/or Company names may be trademarks of their respective owners. 408-8627 Crimp 7.5 Housing Ferrule [0.29] Assembly 2.8 Cable [0.11] Jacket Crimp 1.0 Ferrule [.04] Inner Conductor Cable Braid Dielectric Crimp Using the Tooling in Figure 2 Figure 3 Figure 5 Housing Flared Assembly Cable Inner Conductor Cap Braid Solder the Inner Conductor to the Center Contact Inner Conductor Crimp Figure 6 Ferrule Figure 4 Housing OMNI-FLEX 200 Assembly Cable 6. Solder the cable inner conductor to the center contact in the housing assembly. To avoid personal injury, be sure to exercise DANGER caution when handling hot soldering equipment. STOP  7. Place cap on top of the housing assembly as shown in Figure 6. Press the cap firmly in place. 8. For OMNI-FLEX 200 cable only -- Slide shrink tubing over the cable and crimped ferrule. Heat the shrink tubing and shrink it into place. See Figure 7. Shrink Tubing 4. REVISION SUMMARY Figure 7 • Updated document to corporate requirements. Rev E 2 of 2