Kilovac Solid State Relays Kilovac Solid State Relays Table of Contents DS11 Series DC Relays, 2 Amp Output Rating, Qualified to DSCC Drawing 88062 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2 – 10-5 DS13 Series DC Relays, 2 Amp Output Rating, Qualified to DSCC Drawing 90091 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-6 – 10-9 MS14 Series Solid State Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-10, 10-11 JTS5, 6, & 7 Series, DC & Bi-Directional Output, Up to 250mA & 250V Output Rating, TO-5 Package, Qualified to MIL-PRF-28750/5, /6, & /7 . . . . . . . . . . . . . . . . . . . . . . .10-12 MS18 Series, DC & Bi-Directional Output, Up to 2A & 350V Output Rating, Qualified to DSCC Drawing 89116 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-13, 10-14 JDS9 Series, AC Relays, 2A/250Vrms Rating, Qualified to MIL-PRF-28750/9 . . .10-15, 10-16 PS12 Series, AC Relays, 10A/250Vrms Rating, Qualified to DSCC Drawing 86031 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-17, 10-18 JPS10 Series, AC Relays, 25A/250Vrms Rating, Qualified to MIL-PRF-28750/10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-19, 10-20 10 10–1 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays DS11 Series SSR For DC Loads up to 2A @ 60Vdc Product Facts n Standard options: short circuit/overload protection, switch status and trip status n Optically coupled all solid state relay n TTL & CMOS compatible input DS11 series SSRs feature and wiring; and isolated off and a logic “1” when the n Low on-resistance power state of the art photo-voltaic switch status or trip status. output is on. Trip status, MOSFET output optical isolation and power The overload feature pro- also optically isolated from n Tested per MIL-PRF-28750D MOSFET output chips for vides protection if a short or the load, provides a logic and approved to DSCC ultra-reliable high speed overload develops while the “1” if the output trips off and drawing 88062 with “Y” switching of DC loads up relay is in the on state or if a logic “0” when the output level screening to 2 amps, with extremely the relay is turned on into a is in a normal condition, on low on-resistance. Standard dead short. Switch status, or off, and is available only options include integral optically isolated from the in conjunction with short current overload/short load, signals the status of circuit protection. circuit protection to provide the output and provides a protection of the relay, load logic “0” when the output is Kilovac Part No. DSCC Dwg. No. Relay Version DS11-1Y 88062-008 Basic relay DS11-1000 88062-004 Relay w/ short circuit protection DS11-1001 88062-006 Relay w/ switch status DS11-1002 88062-002 Relay w/ short circuit protection and switch status DS11-1003 N/A Relay w/ short circuit protection and trip status 2 Terminal Input Configuration Direct Drive (Status Optional) TTL Drive Status Output Load V Status V +V Supply Load CC +V Load Supply V CC 1 3 6 OUTPUT INPUT 6 1 3 14 8 12 INPUT OUTPUT 14 8 12 TTL 3 Terminal Input Configuration With Output Status Without Output Status V Load Status Output Status V +V Supply CC Load V +V Load Supply CC 1 3 6 OUTPUT INPUT 14 8 1 3 6 12 INPUT OUTPUT 14 8 12 TTL or CMOS TTL or CMOS 10–2 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays Kilovac Solid State Relays DS11 Series SSR For DC Loads up to 2A @ 60Vdc (Continued) Environmental Characteristics Electrical Specifications (-55°C to +105°C unless otherwise specified) Ambient Temperature Range — Input (2 terminal configuration) Operating — -55°C to +105°C Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Storage — -55°C to +105°C Input current (max.) @ 5Vdc 15mAdc (Notes 1 & 2, Figures 1 & 2) Vibration Resistance — 100 G’s, 10-3,000 Hz Must turn-on voltage 3.8Vdc Shock Resistance — Must turn-off voltage 1.5Vdc 50 G’s, 11 ms pulse Reverse voltage protection -32Vdc Constant Acceleration Resistance Input (3 terminal configuration) (Y1 axis) — 5,000 G’s Control voltage range 0 - 18 Vd Control current (max.) 250μAdc @ 5V, 1mA @ 18V Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Input current (max.) @ 5Vdc 15mADC (Notes 1 & 2, Figures 1 & 2) Mechanical Characteristics Must turn-on voltage 0.3Vdc Weight (approx.) — Must turn-off voltage 3.2Vdc .176 oz. (5 grams) I/O 10 Materials — Dielectric strength (min.) 1,000V rms Header — KOVAR 9 Cover — Nickel Insulation resistance (min.) @ 500Vdc 10 ohms Pins — KOVAR, gold plated Capacitance (max.) 10pF Output Continuous load current (max.) @ 25°C 2.1Adc (Figure 7) Continuous load voltage (max.) 60Vdc Transient blocking voltage (max.) 80Vdc (Note 5) On resistance (max.) @ T = 25°C, I = 100mA 0.15 ohm (Note 6, Figure 6) j L Output voltage drop (max.) 0.5Vdc Leakage current (max.) @ V = 60Vdc 100μAdc Leakage current (max.) @ V = 60Vdc, with switch status 2mAdc Turn-on time (max.) 3 ms (Figure 3) Turn-off time (max.) 1 ms (Figure 3) dv/dt (min.) 100V / μs Electrical system spike 600Vdc (Note 5) Output chip junction temperature (max.) 125°C Thermal resistance (max.), junction to ambient 90°C/W Thermal resistance (max.), junction to case 25°C/W Status Status supply voltage range 1 - 18Vdc Status current (max.) @ Vstatus ≤ 0.4Vdc 600μADC (Figure 5, Note 8) Status leakage current (max.) @ 16Vdc 10μAdc Status turn-on time (max.) 3.5 ms (Figure 4) Status turn-off time (max.) 8 ms (Figure 4) Short Circuit Protection Current surge without tripping (max.), 100ms pulse 4.25Adc Overload trip current (max.), 0.5 ms pulse, V = 60Vdc 10Adc Trip time (typical), turning on into short 400μs Trip time (typical), shorting while relay is on 280μs KOVAR is a trademark of Carpenter Technology Corporation. 10–3 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays DS11 Series SSR For DC Loads up to 2A @ 60Vdc (Continued) Figure 1 - Maximum Input Current vs. Input Voltage Figure 2 - Series Resistance vs. Vcc Supply Voltage (Note 1) 18 1800 15 1500 1200 12 9 900 6 600 3 300 0 0 0 51015 30 20 25 40 50 60 06 10 15 20 25 30 35 Input Voltage, Vcc (Vdc) Vcc (Volts) Figure 3 - Turn-on and Turn-off Timing Figure 4 - Output Status Timing OFF Pin 14 V High Control (Input) 50% Low ON T V S Pin 6-8 Off 90% 90% 10% On 10% T T T Status Status Off On Turn-Off Turn-On Time Time Figure 5 - Status Resistor vs. Status Supply Voltage Figure 6 - On-Resistance vs. Temperature (Note 6) 2.0 35000 1.8 30000 1.6 25000 1.4 1.2 20000 1.0 15000 0.8 0.6 10000 0.4 5000 0.2 0 0.0 05 10 15 20 25 50 75 100125 Junction Temperature (°C) Status Supply Voltage (Volts) 10–4 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Input Current (mA) Status Resistor (ohms) R Series (ohms) Normalized On Resistance Factor (NR) Kilovac Solid State Relays Kilovac Solid State Relays DS11 Series SSR For DC Loads up to 2A @ 60Vdc (Continued) Figure 7 - Temperature Derating Curve Figure 8 - Maximum Surge Current Without Tripping 2.0 7.0 1.8 -55°C 1.6 6.0 1.4 5.0 1.2 +25°C 1.0 4.0 0.8 3.0 0.6 +85°C 0.4 2.0 0.2 1.0 0 10 0.01 0.1 1 10 -50 -40-20 0 20 40 60 80 100120 Time (seconds) Ambient Temperature (°C) Figure 9 - Outline Dimensions .273 ±.020 .530 MAX .490 REF. .140 (13.46) (6.93 ± .50) (12.44) (3.55) .200 .020 MAX. (5.08) (.50) TOP MARKING ORIENT AS .890 MAX. .500 SHOWN (22.60) .850 REF. .600 (12.70) (21.59) (15.24) .190 MAX. .110 DATE CODE (4.82) (2.79) HERE .017 +.002, –.001 DIA. .300 (.43 + .05, –.02) (7.62) 6 PLS. TOLERANCE: ± 0.010 (0.25mm) FOR 2 PLACE DECIMALS, ± 0.005 (0.13mm) FOR 3 PLACE DECIMALS. UNLESS OTHERWISE SPECIFIED Notes 1.2 terminal input configuration is compatible with CMOS or open collector TTL (with pull-up resistor). For Vcc levels above 6Vdc, a series limiting resistor is required. See Fig. 2 for resistor value. Use standard resistor value equal to or less than value from the curve. 2.Input transitions to be ≤ 1ms duration, and input direct drive should be “bounceless contact” type. 3. Vcc = 5Vdc for all tests unless otherwise specified. 4.All DS11 Series relays may drive loads connected to either positive or negative referenced power supply lines. Reversing polarity of output may cause permanent damage. Inductive loads must be diode suppressed. 5.Transient blocking voltage and electrical system spike tests are performed per MIL-STD-704 (28VDC systems). 6.To determine the maximum on-resistance at any given junction temperature, multiply on-resistance at 25°C (0.15 ohm) by normalized on-resistance factor from curve (Fig. 6). 7.Overload testing per MIL-R-28750 is constrained to the limits imposed by the short circuit protection requirements of this specification and DSCC drawing 88062. Load circuit series inductance for “load shorted” mode of operation to be limited to 50mH max. Maximum repetition rate into a shorted load should not exceed 10 Hz. 8.Proper operation of the status feedback requires a status pull-up resistor. See Fig. 5 for status resistor value. 10–5 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Output Current (amps) Surge Current (amps) Kilovac Solid State Relays DS13 SSR for loads up to 2A @ 60Vdc Product Facts n Standard options: short circuit/overload protection and control status. n Optically coupled all solid state relay. n TTL & CMOS compatible input. n Low on-resistance power MOSFET output. DS13 series SSRs employ circuit protection and a control status provides a n Tested per MIL-PRF-28750D state of the art photovoltaic separate input control built-in test function which and approved to DSCC optical isolation and power status line. The overload provides a logic “0” when drawing 90091. MOSFET output chips for feature provides protection the input circuit is energized n All versions available with ultra-reliable high speed of the relay, load and load and functional. The relay is Tyco Electronics “W” level switching of DC loads up circuit wiring in the event of packaged into a custom screening for Kilovac to 2 amps, with low on- a sustained current over- hermetically sealed low- relays. resistance. Standard load or short circuit while profile 8-pin ceramic DIP options include integral the relay is on or when it is package, with through hole current overload/short turned on into a short. The or surface mount pins. Kilovac Part No. DSCC Dwg. No. Relay Version DS13-1Y 90091-008 Basic relay DS13-1000 90091-004 Relay w/ short circuit protection DS13-1001 90091-006 Relay w/ control status DS13-1002 90091-002 Relay w/ short circuit protection and control status Notes: Add suffix “S” to part number for surface mount versions. Add suffix “T” to part number for tinned leads. Add suffix “W” to part number for lower screening level. 2 Terminal Input Configuration Direct Drive TTL Drive S1 R Series (+) Output R Series (+) Output Vcc Load V Load Vcc Load V Load 1 4 1 4 2 Control 2 Control 8 5 5 8 Return Load Return Load Load Return Load (-) Output Return (-) Output O C TTL 3 Terminal Input Configuration With Status Without Status V Status R Status Vso (+) Output (+) Output Status Load Vcc Load V Vcc V Load Output Load 1 4 1 7 4 2 2 V V Control Control Control Control 5 8 5 8 Return Return Load Load Load Load Return Return (-) Output (-) Output 10–6 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays Kilovac Solid State Relays DS13 SSR for loads up to 2A @ 60Vdc (Continued) Environmental Characteristics Electrical Specifications (-55°C to +105°C unless otherwise specified) Ambient Temperature Range: Operating: -55°C to +105°C. Input (2 terminal configuration) Storage: -55°C to +125°C. Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Vibration Resistance: Input current (max.) @ 5Vdc 15mAdc (Notes 1 & 2, Figures 1 & 2) 100 G’s, 10-3,000 Hz. Must turn-on voltage 3.8Vdc Shock Resistance: Must turn-off voltage 1.5Vdc 1,500 G’s, 0.5 ms pulse. Reverse voltage protection -32Vdc Constant Acceleration Resistance: 5,000 G’s. Input (3 terminal configuration) Control voltage range 0 - 18 Vdc Control current (max.) 240μAdc @ 5V, 1mA @ 18V Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Input current (max.) @ 5Vdc 15mAdc (Notes 1 & 2, Figures 1 & 2) Mechanical Characteristics Must turn-on voltage 0.3Vdc Weight (max.): .07 oz. (2 grams) Must turn-off voltage 3.2Vdc 10 Materials: I/O Case: DIP, hermetically sealed, Dielectric Strength (min.) 1,000V rms ceramic 9 Insulation Resistance (min.) @ 500Vdc 10 ohms Pins: Copper, gold plated Capacitance (max.) 10pF Output Continuous load current (max.) @ 25°C, without short circuit protection 2.0Adc (Figure 5, Note 3) Continuous load current (max.) @ 25°C, with short circuit protection 1.0Adc (Figure 5, Note 3) Continuous load voltage (max.) 60Vdc Transient blocking voltage (max.) 80Vdc (Note 4) On resistance (max.) @ T = 25°C, I = 100ma, with short circuit protection 0.45 ohm (Note 5, Figure 4) j L On resistance (max.) @ T = 25°C, I = 100ma, without short circuit protection 0.22 ohm (Note 5, Figure 4) j L Output voltage drop (max.), with short circuit protection 0.6Vdc Output voltage drop (max.), without short circuit protection 0.75Vdc Off-state leakage current (max.) @ 60Vdc 100μAdc Turn-on time (max.) 1.5 ms (Figure 3) Turn-off time (max.) .25 ms (Figure 3) dv/dt (min.) 100V / μs Electrical system spike ±600Vdc (Note 4) Junction temperature (max.) 150°C Thermal resistance (max.), junction to ambient 80°C/W Thermal resistance (max.), junction to case 20°C/W Status Status supply voltage 30Vdc Status sink current (max.) @ Vstatus≤ 0.3Vdc 2mAdc (Note 7) Status leakage current (max.) @ 15Vdc 4μAdc Short Circuit Protection See Figure 6, Note 7 10–7 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays DS13 SSR for loads up to 2A @ 60Vdc (Continued) Figure 1 - Maximum Input Current vs. Input Voltage Figure 2 - Series Resistance vs. Vcc Supply Voltage (Note 1) 18 2000 15 1500 12 9 1000 6 500 3 0 0 0 51015 20 25 30 40 50 60 05 10 15 20 25 30 35 Vcc (Volts) Input Voltage, Vcc (Vdc) Figure 3 - Output Turn-on and Turn-off Timing Figure 4 - On-Resistance vs. Temperature (Note 6) V 2.0 High Control Pin 2 1.8 Low 1.6 V 1.4 Output Off 90% Pin 4-5 1.2 10% On 1.0 0.8 0.6 T T On Off 0.4 0.2 25 50 75 100125 Junction Temperature (°C) Figure 5 - Temperature Derating Curve Figure 6 - Typical Current Trip Levels 5 2.0 DS13-1Y 4 DS13-1001 1.5 3 +25°C 1.0 -55°C 2 DS13-1000 +105°C 0.5 DS13-1002 1 0.0 0 -55 15 25 35 45 55 65 75 85 95 105 115 125 0.01 0.1 1 10 100 1000 Ambient Temperature (°C) Time (seconds) 10–8 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Input Current (mA) Load Current (amps) Normalized On Resistance Factor R Series (ohms) Surge Current (amps) (NF) Kilovac Solid State Relays Kilovac Solid State Relays DS13 SSR for loads up to 2A @ 60Vdc (Continued) Figure 7 - Outline Dimensions Through-Hole Mount Version Surface Mount Version .010 ± .002 .560 MAX. .560 MAX. (.25 ± .05) (14.22) (14.22) 6 PLS 8 7 5 8 7 5 .485 +.010, –.005 .400 ± .015 (12.32 +.25, –.13) .395 MAX. .395 MAX. (10.16 ± .38) (10.03) (10.03) .435 MAX. (11.05) 1 2 4 .010 ± .002 1 2 4 .025 TOP INDEX MARK FOR PIN 1 (.25 ± .05) TOP INDEX MARK FOR PIN 1 (.64) 6 PLS 6 PLS SIDE INDEX MARK FOR PIN 1 SIDE INDEX MARK FOR PIN 1 .016 +.010, –.005 10 .155 MAX. .155 MAX. .036 +.010, –.005 (.41 +.25, –.13) (3.94) (3.94) (.91 +.25, –.13) 6 PLS 6 PLS .150 ± .015 .125 (3.81 ± .38) (3.18) 6 PLS .018 ± .002 .100 .300 (.46 ± .05) (2.54) .125 (7.62) 6 PLS (3.18) .018 ± .002 .100 (.46 ± .05) (2.54) .300 6 PLS (7.62) Notes 1.2 terminal input configuration is compatible with CMOS or open collector TTL (with pull-up resistor). For Vcc levels above 6Vdc, a series limiting resistor is required. See Fig. 2 for resistor value. Use standard resistor value equal to or less than value form the curve. 2.Vcc = 5Vdc for all tests unless otherwise specified. 3.All DS13 Series relays may drive loads connected to either positive or negative referenced power supply lines. Reversing polarity of output may cause permanent damage. Inductive loads must be diode suppressed. 4.Transient blocking voltage & electrical system spike tests are performed per MIL-STD-704 (28Vdc systems). 5.To determine the maximum on-resistance at any given junction temperature, multiply on-resistance at 25°C by normalized on-resistance factor from curve (Fig. 4). 6.Overload testing per MIL-R-28750 is constrained to the limits imposed by the short circuit protection requirements of this specification and DSCC drawing 90091. Load circuit series inductance for “load shorted” mode of operation to be limited to 50mH max. Maximum repetition rate into a shorted load should not exceed 10 Hz. To calculate maximum on-resistance at any temperature, use the following equation: R(on) = R(on) @ 25°C x NF (without short circuit protection) and R(on) = 0.2 x NF + .21 (with short circuit protection) where NF = normalized on-resistance factor from Fig. 4. 7.Proper operation of the status feedback requires a status pull-up resistor. Select the status resistor such that it limits status output current to 2mA: R status = V status – 0.3V / 2mA. 10–9 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays MS14 Series Solid State Relay, With DC or Bi-Directional Output to 350mA @ 400V Product Facts n 1000V optical isolation protects control and driver circuitry from load transients. n Buffered/current limited input for direct drive from CMOS or TTL logic. n Power MOSFET output chips for low voltage drop. MS14 series subminiature high speed switching of DC or from CMOS or TTL. The relay is n 90 & 240mA output current. SSRs employ state of the art bidirectional loads up to 350mA packaged in a custom hermeti- photo-voltaic optical isolation and 400Vdc. The input is cur- cally sealed low-profile .100 n 85, 100 & 400V output providing 1000Vrms input/out- rent regulated and buffered to grid package which conserves voltage. put isolation and power mosfet minimize power dissipation and space for high density PC n Subminiature hermetically output chips for ultra-reliable permit driving the relay direct board circuitry. sealed .100 grid package. Ordering Information n Screened per “Y” level of MIL-PRF-28750D. Kilovac Part No. DSCC Drawing/Pin No. Output Rating MS14-1Y 85092-001 350mA / 400V n Direct replacement for TELEDYNE M92F & M93F MS14-2Y 85092-002 135mA / 400V series MS14-3Y 87034-003 ±240mA / 85V Electrical Specifications (-55°C to +105°C unless otherwise specified) Environmental Characteristics Input (TTL Drive) Ambient Temperature Range: Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Operating: -55°C to +105°C. Storage: -55°C to +125°C. Input current (max.) @ 5Vdc 16mAdc (Notes 1 & 2, Figures 1 & 2) Vibration Resistance: Must turn-on voltage 3.8Vdc 30 G’s, 10-3,000 Hz. Must turn-off voltage 1.5Vdc Shock Resistance: Input (CMOS Drive) 1,500 G’s, 0.5 ms pulse. Control voltage range 0 - 18 Vdc Constant Acceleration Resistance: Control current (max.) 250μAdc @ 5V, 1mA @ 18V 5,000 G’s. Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Input current (max.) @ 5Vdc 16mAdc (Notes 1 & 2, Figures 1 & 2) Mechanical Characteristics Must turn-on voltage 0.3Vdc Weight (max.): Must turn-off voltage 2.8Vdc .07 oz. (2 grams) I/O Materials: Case: Nickel, hermetically sealed. Dielectric Strength (min.) 1,000V rms Pins: Kovar, gold plated 9 Insulation Resistance (min.) @ 500Vdc 10 ohms Output Continuous load current (max.) @ 25°C: MS14-1Y 350mAdc TTL Configuration Continuous load current (max.) @ 25°C: MS14-2Y 135mAdc Continuous load current (max.) @ 25°C: MS14-3Y +/– 240mA +Vcc V 5 7 LOAD Continuous load voltage (max.) @ 25°C: MS14-1Y 100Vdc LOAD 4 Continuous load voltage (max.) @ 25°C: MS14-2Y 400Vdc 3 1 Continuous load voltage (max.) @ 25°C: MS14-3Y +/– 85V LOAD LOAD RETURN TTL On resistance (max.) @ T = 25°C, I = 100mA: MS14-1Y 4 ohms j L On resistance (max.) @ T = 25°C, I = 100mA: MS14-2Y 25 ohms j L On resistance (max.) @ T = 25°C, I = 100mA: MS14-3Y 8 ohms CMOS Configuration j L Off-state leakage I (max.) @ 80% max. V @ –55 to +25°C 1μA +Vcc Off-state leakage I (max.) @ 80% max. V @ =25 to +85°C 50μA V 5 7 LOAD LOAD Junction temperature (max.) 150°C 4 Turn-on time (max.) MS14-1Y & –2Y .7mS CMOS 3 1 LOAD LOAD Turn-on time (max.) MS14-3Y 2mS RETURN Turn-off time (max.) (all versions) 1mS (–) © 2011 by Tyco Electronics Corporation. All Rights Reserved. TE logo and Tyco Electronics are trademarks. Other products and company names mentioned herein may be trademarks of their respective owners. 10–10 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays 4V 8V 12V 16V 20V 24V 28V 32V Kilovac Solid State Relays MS14 Series Solid State Relay, With DC or Bi-Directional Output to 350mA @ 400V (Continued) Figure 1 - Figure 2 - Figure 3 - Max. Input Current vs. Input Voltage Series Res. vs. Vcc Supply Voltage (Note 1) Output Turn-on and Turn-off Timing 2000 18 High Input 15 Low 1500 12 Output Off 90% 9 10% 1000 On 6 500 T T On Off 3 0 0 0 5 10 15 2025 30 4050 60 0 510 15 20 25 30 35 Vcc (Volts) Input Voltage, Vcc (Vdc) 10 Figure 4 - Figure 5 - Figure 6 - Temperature Derating Curve On-Resistance vs. Temperature (Note 6) Simplified Circuit 100 2.0 + OUTPUT 7 Input Supply Voltage (Vcc) 90 +Vcc 5 1.8 80 1.6 CONTROL 4 70 1.4 60 1.2 RETURN 3 50 1 – OUTPUT 1.0 40 0.8 30 0.6 Note: MS14-1Y and -2Y have a single output chip. 20 0.4 10 0.2 0 0.0 25 35 45 55 65 75 85 95 105 115 125 25 50 75 100 125 Ambient Temperature (°C) Junction Temperature (°C) Figure 7 - Outline Dimensions CASE .031 ± .002 .032 TEMPERATURE [.78 ± .05] [.813] MEASUREMENT POINT 71 Unless otherwise specified, tolerances are: .335 .370 ±0.010 [0.25] for 2 place decimals [8.51] .200 TYP. [9.40] ±0.005 [0.13] for 3 place decimals .100 TYP. SQUARE [5.08] SQUARE 53 4 [2.54] MAX. MAX. Terminal numbers are for reference only and do not appear on the header. .085 REF. .275 MAX. .085 REF. [2.16] .080 [2.03] DIA. [6.99] [2.16] .70 MIN. GLASS BEAD .100 TYP. [17.8] 5 PLACES [2.54] Notes 1.2 terminal input configuration is compatible with CMOS or open collector TTL (with pull-up resistor). 2.For Vcc levels above 6Vdc, a series limiting resistor is required. See Fig. 2 for resistor value. Use standard resistor value equal to or less than value form the curve. 3.Vcc = 5Vdc for all tests unless otherwise specified. 4.All MS14 Series relays may drive loads connected to either positive or negative referenced power supply lines. Inductive loads must be diode suppressed. 5.If an input series current limiting resistor is used, derating of output current vs. Vcc is not necessary. Curve for 4V applies. 6.On-resistance at any ambient temperature other than 25°C can be computed as follows: 0.006 R (@ any T) = R (@ +25°C) x e , where T = new temperature – 25°C, e = 2.7182818 . 9-1773439-2–PDF–KRG–9-07 10–11 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. % Output Current Input Current (mA) Normalized On Res. Factor (NF) R Series (ohms) Kilovac Solid State Relays JTS5, 6, & 7 Series, DC & Bi-Directional Output, Up to 250mA & 250V Output Rating, TO-5 Package Input Characteristics Output Characteristics Environmental Characteristics Input Voltage Range — Max. Output Current Shock — 1500 G’s, 0.5 ms. 4.0 – 7.0 Vdc (Continuous, 25°C) — Vibration — 100 G’s, 10 to 2000 Hz 50 mAac or mAdc (JTS5-1Y) Maximum Turn-on Voltage — Operating Ambient Temperature — 250 mAdc (JTS6-1Y) 5.0 Vdc -55 to +125°C 100 mAdc (JTS7-1Y) Minimum Turn-off Voltage — Max. Output Voltage — 1.0 Vdc 40 Vac or Vdc (JTS5-1Y) I/O Dielectric — 1000 Vac pk-pk 40 Vdc (JTS6-1Y) 250 Vdc (JTS7-1Y) Max. On-resistance — CONTROL 5 ohms (JTS5-1Y) LOAD SOURCE 1 3 Turn-on Time — 10 μsec. 7 5 Turn-off Time — 15 μsec. DC SUPPLY + + .370 DIA MAX (9.40) .335 DIA MAX (8.51) CONTROL LOAD SOURCE 1 3 .275 MAX AC OR ±DC (6.99) 7 5 SUPPLY .50 MIN (12.70) Terminal View .017 DIA (.43) 45° .031 (.79) Product Facts .032 n Hermetically sealed TO-5 (REF) (.81) package .100 (2.54) n Transformer coupled .200 n High speed switching (5.08) n JTS5-1Y switches AC or DC JTS5/JTS6/JTS7 n Qualified to M28750/5, 6, & 7 Notes: 1) Reversing polarity of input (or output except for JTS5-1) may cause permanent damage. 2) Input must be a step function. Rise or fall time, as applicable, not to exceed 100 μsec. 3) Inductive loads must be diode suppressed. 4) For any control voltage, the maximum load current shown on graphs must not be exceeded. Attempting to draw currents in excess of those specified on graphs can cause permanent damage. 300 300 60 7 Vdc INPUT 7 Vdc INPUT 50 200 200 6 Vdc INPUT 40 6 Vdc INPUT 30 5 Vdc INPUT 5 Vdc INPUT RATED CURRENT RATED CURRENT 100 100 7 Vdc INPUT 20 90 90 4 Vdc INPUT 80 80 6 Vdc INPUT 70 70 4 Vdc INPUT 10 60 60 5 Vdc INPUT 50 50 RATED CURRENT 7 40 40 5 4 Vdc INPUT 30 4 30 3 20 20 2 10 10 1 -60 -40 -20 0 20 40 60 80 100120140 -60 -40 -20 0 20 40 60 80 100120140 -60 -40 -20 0 20 40 60 80 100120140 Ambient Temperature (°C) Ambient Temperature (°C) Ambient Temperature (°C) JTS5-1Y JTS6-1Y JTS7-1Y Output Current Vs. Input Control Voltage and Ambient Temperature 10–12 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. –55°C –125°C –55°C –125°C –55°C –125°C Output Current (mA) Output Current (mA) Output Current (mA) Kilovac Solid State Relays Kilovac Solid State Relays MS18-1006 High Performance DC and Bi-directional Solid State Relay For Loads up to 2A @ 80Vdc Product Facts n Bi-directional power FET output n Optically coupled n Low on-resistance n Extremely low leakage current The MS18-1006 is an opti- to configure the output stand high inrush currents n Subminiature hermetically cally coupled SSR employ- switching circuit for DC up to 350% of rated. The sealed package ing power MOSFET output operation up to 2A with low profile subminiature n Tested per MIL-PRF-28750D chips in an inverse series very low on-resistance. The package is hermetically and approved to DSCC configuration for switching relay features fast switching sealed with pinouts on a drawing 89116-006 DC or bi-directional loads. speeds, low off-state leakage, 0.1” x 0.3” grid pattern. A common source connec- virtually zero offset voltage tion is provided for the user and the capability to with- 10 Kilovac Part No. DSCC Dwg. No. Relay Version MS18-1006 89116-006 Basic relay Environmental Characteristics Electrical Specifications (-55°C to +120°C unless otherwise specified) Ambient Temperature Range — Input Operating — -55°C to +120°C Input current (max.) 25mAdc Storage — -55°C to +125°C Input voltage drop (max. @ 25mA)) 1.5 Vdc Vibration Resistance — Must turn-on current 10mA 100 G’s, 10-2,000 Hz Shock Resistance — Must turn-off current 10μA 1,500 G’s, 0.5 ms pulse Reverse voltage protection -5.0Vdc Constant Acceleration Resistance I/O (Y-1 axis) — Dielectric strength (60Hz., 1mA leakage) 500V rms 5,000 G’s 9 Insulation resistance (min.) @ 500Vdc 10 ohms Capacitance (max. @ 25Vdc, 1 Mhz) 5pF Mechanical Characteristics Output Weight (approx.) — Continuous load current, parallel (DC) configuration (max.) 2A (Figure 2) .07 oz. (5 grams) Continuous load current, series (bi-directional) configuration (max.) 1A (Figure 2) Materials — Header — Kovar® Alloy Continuous operating load voltage (max.) +/– 80V Cover — Grade A Nickel Transient blocking voltage (5 sec max.) +/– 90V Pins — Kovar® Alloy, gold plated Overload (100ms, 10% duty cycle, 10 cycles max.) 350% of rated dv/dt (min.) 100V / μs On resistance (max.), parallel (DC) configuration 0.4 ohm On resistance (max.), series (bi-directional) configuration 0.6 ohm Turn-on time (max, @ +/– 80V) 800μs (Figure 3) KOVAR is a trademark of Carpenter Turn-off time (max, @ +/– 80V) 500μs (Figure 3) Technology Corporation. Thermal resistance, junction to ambient 110°C/W Thermal resistance, junction to case 20°C/W Figure 1 – Wiring Diagrams Series Connection Parallel Connection V V V V (in) (load) (in) (load) TOP VIEW TOP VIEW LOAD LOAD R R S S 1 6 1 6 2 5 2 5 N/C 3 4 3 4 CASE CASE GROUND GROUND 10–13 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. TYCO ELECTRONICS 58614 MS18-1006 ± 80V - 1.0A Kilovac Solid State Relays MS18-1006 High Performance DC and Bi-directional Solid State Relay For Loads up to 2A @ 80Vdc (Continued) Figure 2 - Temperature Derating Curves Series Configuration Parallel Configuration 2.4 1.2 1.1 2.2 1.0 2.0 0.9 1.8 0.8 1.6 1.4 0.7 0.6 1.2 0.5 1.0 0.4 0.8 0.3 0.6 0.4 0.2 0.1 0.2 0 0 5 15 25 35 45 55 65 75 85 95 105 115 125 5 15 25 35 45 55 65 75 85 95 105 115 125 AMBIENT TEMPERATURE (°C) AMBIENT TEMPERATURE (°C) Figure 3 - Turn-on and Turn-off Timing Figure 4 - Functional Block Diagram HIGH PIN 1 REF TO 2 1 6 LOW BIAS LINE FLOATING TIMING OFF 90% POWER & SIGNAL PIN 6 TO 4 SUPPLY COND. 2 5 10% ON RTN RTN T(ON) T(ON) 3 4 CASE LINE GND Figure 5 - Outline Dimensions 0.463 MAX. 0.190 MAX. (11.76) (4.83) 0.160 0.109 0.300 (4.06) (2.77) (7.62) MIN. 0.418 0.100 (10.62) (2.54) 0.200 (5.08) 0.084 ±.005 0.020 MAX. DATE CODE ON (2.13 ± .127) (0.508) THIS SURFACE 0.017 +.002, –.001 6 PLS (0.432 +.051, –.025) Notes 1. An external resistor must be in series with the input at all times. 2. Do not ramp input current. Input transition should be <1.0ms. 3. Input current/series resistor calculation (Approx.): I = V – V /R . (input) IN DROP SERIES 4. Unless otherwise specified parametric testing is accomplished at 25ma input current. (X • ∆T) 5. To calculate R for temperatures other than 25°C, use the following equation: T = (R at + 25°C) • e where x = 0.0065. DS(ON) (TEMP) DS(ON) 6. Inductive loads must be diode suppressed. 7. Continuous load current is rated under conditions of still air. 8. Load may be connected to either side of relay, sink or source modes. 9. Reverse polarity >5Vdc may cause permanent damage 10. Acceptance testing is accomplished in the series (bi-directional) mode. 11. DSCC part numbers 89116-002 & 89116-004 are also available. 10–14 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. LOAD CURRENT (AMPS RMS) LOAD CURRENT (AMPS DC) Kilovac Solid State Relays Kilovac Solid State Relays JDS9 Series, AC Relays, 2A/250Vrms Rating Input Characteristics Output Characteristics Environmental Characteristics Input Voltage Range — Max. Output Current (Continuous, Shock — 1500 G’s, 0.5 ms. 3.8 – 32 Vdc 25°C) — 2 Arms Vibration — 30 G’s, 10 to 3000 Hz Pick-up Voltage — Max. Output Voltage — 250 Vrms Operating Ambient Temperature — 3.8 Vdc Peak Over Voltage Rating — -55 to +110°C 500 Vpk Dropout Voltage — 1.5 Vdc Frequency Range — 40 – 440 Hz I/O Dielectric — 1500 Vrms Zero Switch Window — 15 Vpk Thermal Resistance — Junction to Ambient — 65°C/Watt _ + Junction to Case — 15°C/Watt 1 1 6 8 .890 MAX (22.6) 10 1 6 .530 MAX .300 ± .005 LOAD (13.5) (7.62 ± .127) 18 AC POWER .100 REF (2.54) .200 REF .140 REF Terminal View (5.08) (3.56) .500 REF (17.7) .600 REF (15.2) .190 MAX .850 (21.6) REF .490 REF (12.4) (4.83) Product Facts .020 MAX (.508) n Hermetically sealed n Thick film hybrid construction .270 ± .020 .017 ± .001 (6.86 ± .51) n Optically isolated (.432 ± .025) n Zero voltage turn-on n Qualified to MIL–R–28750/9 JDS9-1Y 3.0 2.8 2.6 2.4 2.2 CASE TEMPERATURE 2.0 AT 32 Vdc INPUT 18 AT 5 Vdc INPUT 1.8 15 1.6 1.4 12 AMBIENT TEMPERATURE 1.2 AT 32 Vdc INPUT 1.0 9 AT 5 Vdc INPUT 0.8 6 0.6 0.4 3 0.2 0.0 0 20 30 40 50 60 70 80 90 100 110 120 130 0 510 15 20 25 30 40 50 60 TEMPERATURE (°C) INPUT VOLTAGE (Vdc) JDS9 Max. Output Current vs. Temperature JDS9 Typical Input Current vs. Input Voltage 10–15 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. LOAD CURRENT (AMPERES) INPUT CURRENT (mA) Kilovac Solid State Relays JDS9 Series, AC Relays, 2A/250Vrms Rating (Continued) Electrical Specifications (-55°C to +105°C unless otherwise specified) Input Input supply voltage range (Vcc) 3.8 - 32 Vdc Input current (max.) @ 5Vdc 15mAdc Must turn-on voltage 3.8Vdc Must turn-off voltage 1.5Vdc Reverse voltage protection -32Vdc I/O Dielectric strength (min.) 1,500V rms/60 Hz. 9 Insulation resistance (min.) @ 500Vdc 10 ohms Capacitance (max.) 10pF Output Output current rating (max.) 2A rms (Fig. 2, Note 1) Surge current (max.), 16ms @ 25°C (max.) 8A pk (Fig. 1, Note 3) Continuous load voltage (max.) 250V rms Transient blocking voltage (max.) 500V pk Frequency range 40 - 440 Hz. Output voltage drop (max.) @ 1A load current 1.5V rms Off-state leakage current (max.) @ 250V rms/400 Hz. 1mA rms Turn-on time (max.) 1/2 cycle Turn-off time (max.) 1 cycle Off-state dv/dt (min.), with snubber 200V /μs (Note 2) Zero voltage turn-on window (max.) 10V Wave distortion (max.) 4V rms Output chip junction temperature (max.) 130°C Thermal resistance (max.), junction to ambient 65°C/W Thermal resistance (max.), junction to case 15°C/W Notes 1. Operation at elevated load currents up to 2 amps is dependent on the use of suitable heatsink to maintain case temperature. 2. Recommended output snubber: R = 100 ohms (1/2 W), C = .01μF (600V). 3. Heating of output chip during and after a surge may cause loss of output blocking capability until junction temperature falls below maximum rating. 10–16 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays Kilovac Solid State Relays PS12 Series High Performance Solid State Relays For AC Loads up to 10A @ 250Vrms Product Facts n Approved to DSCC drawing 86031 n Optically coupled all solid state relay n TTL compatible input n Zero voltage turn-on for low EMI n Custom power package with screw terminals The PS12 series solid state resistive or reactive loads. MIL-PRF-28750D, and the relay is designed for AC TTL compatible input cir- PS12-1W screened per 10 power switching up to cuitry is optically isolated to Tyco Electronics specifica- 10 amps at 250Vrms. The 1,500Vrms from the AC load tions for Kilovac relays, circuit employs back-to-back circuit. The relay is offered equivalent to former “W” SCRs with zero voltage turn- in two versions: the PS12-1Y level of Mil-R-28750. on for reliable switching of with “Y” level screening per Kilovac Part Number DSCC Part Number Screening Level PS12-1Y 86031-001 Y PS12-1W N/A W Circuit Diagram Outline Drawing Terminal View TERMINAL NO. 3.8-32VDC EMBOSSED CONTROL IN COVER INPUT 1 3 MATERIAL 1.00 4 PLS 2 1 (25.4) .600 – + .300 (15.24) .50 2 4 (7.62) (12.7) 3 4 .44 (11.2) NO. 6 BINDER .88 (22.4) .150 DIA (3.81) HEAD SCREW EXT. 2.00 MAX (50.8) MTG. HOLE 4 PLS LOAD 120-250 VRMS .90 MAX .78 REF .045 (22.9) (19.8) (1.14) .750 (19.1) ANTI-ROTATIONAL .110 DIA (2.79) TOLERANCE: ± .010 (.25) BOSS UNLESS OTHERWISE NOTED 10–17 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Kilovac Solid State Relays PS12 Series High Performance Solid State Relays For AC Loads up to 10A @ 250Vrms (Continued) Environmental Characteristics Electrical Specifications (-55°C to +95°C unless otherwise specified) Ambient Temperature Range — Input Operating — -55°C to +95°C Input supply voltage range (Vcc) 3.8 - 32 Vdc Storage — -55°C to +110°C Input current (max.) @ 5Vdc 16mAdc Vibration Resistance — 30 G’s, 78-2,000 Hz Must turn-on voltage 3.8Vdc Shock Resistance — Must turn-off voltage 1Vdc 100 G’s, 6 ms pulse Reverse voltage protection -32Vdc Constant Acceleration Resistance — I/O 100 G’s Dielectric strength (min.) 1,500V rms/60 Hz. 8 Insulation resistance (min.) @ 500Vdc 10 ohms Capacitance (max.) 15pF Output Output current rating (max.) 10A rms (Fig. 2, Note 1) Mechanical Characteristics Surge current (max.) 100A pk (Fig. 1, Note 2) Weight (max.) — 3 oz. (85 grams) Continuous load voltage (max.) 250V rms Materials — Transient blocking voltage (max.) 460V pk Case — Plastic, self-extinguishing, Frequency range 45 - 440 Hz. epoxy filled Output voltage drop (max.) @ 25A load current 1.5V rms Terminals — Brass, nickel-plated Base Plate — Aluminum Off-state leakage current (max.) @ 220V rms/400 Hz. 9mA rms NOTE: Do not exceed 125 in-oz when Turn-on time (max.) 1/2 cycle tightening screws. Turn-off time (max.) 1 cycle Off-state dv/dt (min.), with snubber 200V /μs (Note 3) Zero voltage turn-on window (max.) ±15V pk Output chip junction temperature (max.) 125°C (Note 1) Thermal resistance (max.), junction to ambient 11.5°C/W Thermal resistance (max.), junction to case 2.0°C/W 2 2 Fusing I T, 1 ms (max.) 150A s Load power factor (min.) 0.2 Power dissipation (max.) 1.5W/A Notes 1. Operation at elevated load currents up to 10 amps is dependent on the use of suitable heatsink to limit junction temperature. 2. Heating of output chips during and after a surge may cause loss of output blocking capability until junction temperature falls below maximum rating. 3. Internal snubber network is provided across output chips. Figure 1 - Peak Surge Current vs. Surge Current Duration Figure 2 - Load Current vs. Temperature 1°C/W HEAT SINK 1000 10 8 800 6 600 NO HEAT SINK 4 400 2 200 0 0 20 30 40 50 60 70 80 90 100 110 120 10 1001000 10,000 Ambient Temperature (°C) Surge Current Duration (mSec) 10–18 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Peak Surge Current, Non-Repetitive (% of Rated Current) Load Current (Amps rms) Kilovac Solid State Relays Kilovac Solid State Relays JPS10 Series High Performance Solid State Relays For AC Loads up to 25A @ 250Vrms Product Facts n Qualified to MIL-PRF-28750D (Mil Part Numbers M28750/10-001Y and M28750/10-002Y) n Optically coupled all solid state relay n TTL compatible input n Zero voltage turn-on for low EMI n Custom power package The JPS10 series solid state switching of resistive or zero voltage turn-on window relay is designed for AC reactive loads. TTL compat- of 15 volts (preferred version 10 power switching up to ible input circuitry is optically for resistive loads), and the 25 amps at 250Vrms. The isolated to 1,500Vrms from JPS10-2Y with a maximum circuit employs back-to- the AC load circuit. The relay window of 40 volts (pre- back photo SCRs with zero is offered in two versions: the ferred version for reactive voltage turn-on for reliable JPS10-1Y with a maximum loads). Kilovac Part Number Military Part Number Zero Crossing Window JPS10-1Y M28750/10-001Y 15 V pk max. JPS10-2Y M28750/10-002Y 40 V pk max. Circuit Diagram Outline Drawing Terminal View .172 (4.37) - 3 PLS .245 ±.025 2 PLS CONTRASTING _ FOR #8 [.164 (4.17)] + (6.22 ± .63) DC Control BEAD IS SCREW + INPUT TERMINAL Source .040 ±.002 DIA. 12 (1.02 ± .05) 2 1.99 1 (50.5) 2.41 MAX. ±.002 .080 DIA. (61.2) 2.05 (2.03 ± .05) (52.1) 34 COPPER 3 4 CORED WIRE AC Power .825 LOAD .505 ±.025 2 PLS (20.96) (12.83 ± .63) 1.57 MAX. (39.9) TOLERANCE: ±.010 (.25) UNLESS OTHERWISE NOTED 1.845 MAX. 1.30 MAX. (46.86) TERMINAL NUMBERS SHOWN (33.0) ARE FOR REFERENCE ONLY, AND DO NOT APPEAR ON RELAY. 10–19 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Ambient Temperature (W/O Heat Sink) Kilovac Solid State Relays JPS10 Series High Performance Solid State Relays For AC Loads up to 25A @ 250Vrms (Continued) Environmental Characteristics Electrical Specifications (-55°C to +105°C unless otherwise specified) Ambient Temperature Range — Input Operating — -55°C to +110°C Input supply voltage range (Vcc) 4 - 32 Vdc Storage — -55°C to +125°C Input current (max.) 16mAdc Vibration Resistance — 30 G’s, 10-3,000 Hz Must turn-on voltage 4Vdc Shock Resistance — Must turn-off voltage 1Vdc 1,500 G’s, 0.5 ms pulse Reverse voltage protection -32Vdc Constant Acceleration Resistance I/O (Y1 axis) — 5,000 G’s Dielectric strength (min.) 1,500Vrms/60 Hz. 9 Insulation resistance (min.) @ 500Vdc 10 ohms Capacitance (max.) 20pF Output Mechanical Characteristics Output current rating (max.) 25Arms (Fig. 2, Note 1) Weight (max.) — Surge current (max.) 80A pk (Fig. 1, Note 2) 6 oz. (170 grams) Continuous load voltage (max.) 250Vrms Materials — Transient blocking voltage (max.) 500V pk Case — Aluminum, hot tin dipped Terminals — Copper cored wire, gold Frequency range 45 - 440 Hz. plated Output voltage drop (max.) @ 25A load current 1.5Vrms Off-state leakage current (max.) @ 220Vrms/400 Hz. 10mArms Turn-on time (max.) 1/2 cycle Turn-off time (max.) 1 cycle Off-state dv/dt (min.), with snubber 100V /μs (Note 3) Zero voltage turn-on window (max.), JPS10-1Y 15V pk Zero voltage turn-on window (max.), JPS10-2Y 40V pk Waveform distortion (max.) 4Vrms Output chip junction temperature (max.) 125°C (Note 4) Thermal resistance (max.), junction to ambient 6.8°C/W Thermal resistance (max.), junction to case 1.2°C/W Notes 1. Operation at elevated load currents up to 25 amps is dependent on the use of suitable heatsink to maintain case temperature per Fig. 2. 2. Heating of output chips during and after a surge may cause loss of output blocking capability until junction temperature falls below maximum rating. 3. Internal snubber network is provided across output chips. 4. Case temperature measurement point is center of mounting surface. Figure 1 - Peak Surge Current vs. Surge Current Duration Figure 2 - Load Current vs. Temperature Case Temperature 26 24 1000 22 20 800 18 16 14 600 12 10 400 8 6 200 4 2 0 0 10 1001000 10,000 -55 -35-15 0525456585 105 125 Surge Current Duration (mSec) Temperature (°C) 10–20 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change. Peak Surge Current, Non-Repetitive (% of Rated Current) Output Current (Amps rms)