TE CONNECTIVITY 1954381-3

SOLARLOK Interconnection System Installation Manual 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual 1. Safety Note n The SOLARLOK connector is to be used only to interconnect firmly fixed cables. n D o not disconnect under electrical load! ! n E lectrical current path should only be disconnected using approved devices. n Only cables released from TE Connectivity are permitted to be used with SOLARLOK component cable assemblies. n S OLARLOK component cable shall be labeled with label PN 1718077-1 “Do not disconnect under load”. n T o protect against shock, ensure that conductors and their associated connectors are separated from opposite polarity components. n U nconnected connectors must always be protected from pollution (e.g. dust, humidity, foreign particles, etc.), prior to installation. Do not leave unconnected (unprotected) connectors exposed to the environment. The usage of TE connector dust caps is strongly recommended. n C onnectors that are unmated in the field should also be protected from pollutants. n D o NOT use any oil or lubricants during mounting. 2. Tools 2 2 (1) Stripping Tool 1.5 mm – 6.0 mm , 10 AWG PN 4-1579002-2 2 2 (2) Crimping Tool 4.0 mm and 6.0 mm , 10-12 AWG PN 1-1579004-2 (3) Extraction Tool all terminals PN 1102855-3 (4) Field Service Kit all in one PN 1534858-1 (4) (1) (2) (3) (2) (3) 1 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual 3. Assembly Steps 3.1 Using the appropriate wire stripping tool, strip the wire 9 mm ± 1 mm without damaging the strands. 3.2 Insert the stripped wire into the terminal wire crimp barrel until it stops. While holding the wire in place, squeeze the crimp tool handles together until the ratchet releases. 3.3 Press the seal and cable pinch ring assembly into the connector housing until it stops. If you use the pre-assembled connector kit, please go to 3.5! 3.4 Screw back shell nut onto connector housing. 2 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual Pre-Assembled (Connector Kit) 3.5 Push contact with cable into the connector housing until you hear the contact give an audible click and you feel the contact reach the end position. To verify contact engagement, give a slight gentle pull back on the cable, to be sure that the contact is locked. “CLICK” 3.6 Tighten the cable screw lock. The initial assembly tightening torque is 1.3 + 0.2 Nm. For this, a slotted socket wrench with wrench size 13 mm, is recommended. 4. Connector Mating n W hen mating the SOLARLOK connectors, connectors labelled with a “+” or “-” are keyed and can only be mated with equally (same polarity) marked and keyed connectors. n T he connector system is fully latched only when the latches have clicked onto the mating connector. n T he “neutral” designated male connector incorporates no keying features and may be freely mated to either “+” or “-” keyed plug connectors. The neutral product should not be used when maintaining polarity is critical. It is only permitted for serial connections. 3 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual 5. Wiring Radius (r) min. 5x cable Ø ! r = correct! 6. Connector Unmating Depress locking latches Pull apart 4 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual Table 1 Available Connector Kits for SOLARLOK Interconnection System Female Cable Connectors Part Number Description Wire Size Insulation O.D. Range 2 4-1394462-6 Plus Female 2.5mm / 14AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 4-1394462-8 Plus Female 4.0mm / 12AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 6-1394462-3 Plus Female 6.0mm / 10AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 4-1394462-7 Minus Female 2.5mm / 14AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 4-1394462-9 Minus Female 4.0mm / 12AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 6-1394462-4 Minus Female 6.0mm / 10AWG 4.5 to 6.0 mm / 0.177-0.236 in Male Cable Connectors 2 1394461-7 Plus Male 2.5mm / 14AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 7-1394461-0 Plus Male 4.0mm / 12AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 7-1394461-3 Plus Male 6.0mm / 10AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 1394461-8 Minus Male 2.5mm / 14AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 7-1394461-1 Minus Male 4.0mm / 12AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 7-1394461-4 Minus Male 6.0mm / 10AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 6-1394461-3 Neutral Male 2.5mm / 14AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 7-1394461-2 Neutral Male 4.0mm / 12AWG 4.5 to 6.0 mm / 0.177-0.236 in 2 7-1394461-5 Neutral Male 6.0mm / 10AWG 4.5 to 6.0 mm / 0.177-0.236 in Male housing Female housing 5 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual Table 2 Replacement Contacts (screw-machined) for SOLARLOK System Wire Gauge | Wire Size Male Contact PN Female Contact PN 2 2.5 mm | 14 AWG 0-1987280-1 0-1987281-1 2 4.0 mm | 12 AWG 0-1987280-2 0-1987281-2 2 6.0 mm | 10 AWG 0-1987280-4 0-1987281-3 *HVT contact system Maximum Operating Conditions Max. system voltage: 1000V (for UL 600V), max. current 25A@85°C Ambient temperature: -40°C up to 85°C, (for UL 75°C) at full load Please also refer to the following specifications: Application specification 114-18488-1 as well as instruction sheets 411-18305-1 and 114-94061-1 to ensure correct connector assembly and crimp quality. For additional details, please refer to product specification 108-18701. For additional info, please visit our website at: te.com/solar 6 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual Accessories: Dust Covers Female Housing – Dust Cap PN Package Quantity 1987424-1 100 Male Housing – Dust Plug PN Package Quantity 1987419-1 100 The usage of connector re-usable dust covers until ! final assembly is strongly recommended. When the dust cover is mounted, the connector fulfils IP44 (dust and splash proof) according to IEC 60529. 7 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual Connector Safety Devices Locking Collar Unlock Instruction Package PN Required through Sheet Quantity NEC* / USA Flat-blade- 2106207-1 UTE C15-712 408-10296 100 screwdriver / France *for detailed informations see NEC 2008: 690.33 Safety Clip Pivoted Package PN Unlock through Required Quantity 1534226-1 Tool less – 100 8 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual Solar Cable USE-2 Solar AWG Cable Wire Size Color Part Number Quantity 14 AWG Black 1986166-2 500 Black 1986166-3 2500 12 AWG Black 1986165-2 500 Black 1986165-3 1600 10 AWG Black 1986164-2 500 Black 1986164-3 1000 This UV resistant cable can be used in the following photovoltaic applications: n Between solar panels n Between solar roof tiles n Between panels and the AC/DC inverters Approval: n UL 854 approved n Approved for outdoor use Material: n Cable conductor is pre-tinned, stranded copper wire. n Outside wire jacket provides a robust layer of protection and is UV resistant Voltage: 600V Temperature Range: -40 °C – +90 °C 9 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar 2-1773458-2 SOLARLOK Interconnection System Issued 4-2011 Installation Manual Grounding Solutions Grounding Clip and Grounding Bolt Only for solid un-insulated copper wire Instruction Package PN Description Sheet Quantity 12-10AWG Grounding Clip 1954381-1 408-10160 100 with Self-Tapping Screw 12-10 AWG Grounding Clip 1954381-2 408-10160 100 with Screw and Nut 12-10 AWG Grounding Clip 1954381-3 408-10160 100 with Screw, Nut and Locking Ring 6-12 AWG Grounding Bolt, 2106831-1 408-10262 100 # 10-32 UNC Long Tail 6-12 AWG Grounding Bolt, 2058729-1 408-10262 100 # 8-32 UNC Std Tail Grounding Clip Grounding Bolt 3 easy steps to ground your PV system: 1. Insert 2. Push 3. Ready! 10 All specifications subject to change. Consult Tyco Electronics for latest specifications. te.com/solar FOR MORE INFORMATION te.com/solar TE Technical Support Center Internet: te.com/help USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico +52 (0) 55-1106-0800 Latin/S. America: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 Part numbers in this brochure are RoHS Compliant*, unless marked otherwise. *as defined www.te.com/leadfree te.com/solar © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. company. All Rights Reserved. 2-1773458-2 CIS FP 3M 04/2011 SOLARLOK, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Other logos, product and/or company names might be trademarks of their respective owners. While TE has made every reasonable effort to ensure the accuracy of the information in this brochure, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this catalog are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.