TE CONNECTIVITY 625022-000

SPECIFICATION CONTROL DRAWING MATERIALS 1. INSULATION SLEEVE: Heat-shrinkable, transparent blue, radiation cross-linked modified polyvinylidene fluoride. 2. SOLDER PREFORM WITH FLUX: SOLDER: TYPE Sn63 per ANSI J-STD-006. FLUX: TYPE ROL1 per ANSI-J-STD-004. APPLICATION 1. Part will recover to 0.76 (0.03) . 2. This part is designed to meet the requirements as shown below when tested to Raychem Specification RT-1404. QUALIFICATION TEST ASSEMBLIES The test configuration shall be a follow-through splice made by connecting two wires having 26 AWG tin or silver plated conductors and insulations rated for at least 125°C. REQUIREMENTS: Temperature Rating 150°C Voltage Drop** Initial 25 millivolts max. Tensile Strength* 7 lbs. min. Vibration** MIL-STD-202, Method 204, Condition D Voltage Drop after Vibration - 32 millivolts max. Temperature Cycling** -63±3°C to 150±3°C, 5 cycles (Condition C) Voltage Drop after Cycling - 32 millivolts max. Current Cycling** Voltage Drop after Cycling - 32 millivolts max. Heat Aging* 120±2 hours at 200±3°C. Fluid Resistance* 20 hours at 25±3°C in fluids of MIL-H-5606, MIL-I-7808, and MIL-L-9236. Corrosion Resistance* 96 hours at 35±3°C (Condition A). Voltage Drop after test - 32 millivolts max Corrosive Effect* 16 hours at 121±2°C, Non-corrosive * For test procedures, see Raychem Specification RT1404. ** For test procedures, see page 2. TITLE: DEVICES SOLDERSLEEVE 300 Constitution Drive 1.47 (0.058) I.D. MINIATURE Menlo Park, CA 94025, USA UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS. DOCUMENT NO.: D-110-00 INCHES DIMENSIONS ARE BETWEEN BRACKETS. TOLERANCES: ANGLES: N/A Raychem reserves the right to amend this DCR NUMBER: REPLACES: 0.00 N/A drawing at any time. Users should evaluate D000141 n/a 0.0 N/A ROUGHNESS IN the suitability of the product for their 0 N/A MICRON application. DRAWN BY: DATE: PROD. REV.: DOC ISSUE: SCALE: SIZE: SHEET: M. FORONDA 22-Mar-00 P 1 None A 1 of 2 If this document is printed it becomes uncontrolled. Check for the latest revision. SPECIFICATION CONTROL DRAWING TEST PROCEDURES: Voltage Drop: As outlined in RT-1404 with these exceptions: Shall be measured with a 3.0 amp current imposed on splice. Measured over a two inch length which includes the splice. Vibration: Splices shall be mounted so that the center of the splice is 152.4±12.7 (6.0±0.5) from the vibrating member. The splice shall then be vibrated as indicated. One axis of vibration shall be parallel to the splices wires. Upon completion, the voltage drop shall be measured as outlined above. Current Cycling: Three foot lengths of wire shall be spliced and subjected to 50 current cycles. Each cycle shall consist of 30 minutes at 3.75 amperes, followed by 15 minutes at no lead. Voltage drop shall be measures as outlined above. TITLE: DEVICES SOLDERSLEEVE 300 Constitution Drive 1.47 (0.058) I.D. MINIATURE Menlo Park, CA 94025, USA UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS. DOCUMENT NO.: D-110-00 INCHES DIMENSIONS ARE BETWEEN BRACKETS. TOLERANCES: ANGLES: N/A Raychem reserves the right to amend this DCR NUMBER: REPLACES: 0.00 N/A drawing at any time. Users should evaluate D000141 n/a 0.0 N/A ROUGHNESS IN the suitability of the product for their 0 N/A MICRON application. DRAWN BY: DATE: PROD. REV.: DOC ISSUE: SCALE: SIZE: SHEET: M. FORONDA 22-Mar-00 P 1 None A 2 of 2 If this document is printed it becomes uncontrolled. Check for the latest revision.