TE CONNECTIVITY 82A0111-10-2

82A0111 SPECIFICATION CONTROL DRAWING TITLE Date Revision WIRE, RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE-INSULATED, 6-5-13 T LIGHTWEIGHT, GENERAL PURPOSE, 600 VOLT This specification sheet forms a part of the latest issue of Raychem Specification 80. INSULATION - RADIATION-CROSSLINKED, CONDUCTOR - TIN-COATED COPPER MODIFIED FLEXIBLE ETFE TABLE I. CONSTRUCTION DETAILS DIAMETER OF FINISHED WIRE STRANDED WIRE CONDUCTOR MAXIMUM PART NUMBER MAXIMUM CONDUCTOR SIZE STRANDING RESISTANCE DIAMETER 1/ (in.) WEIGHT (AWG) (number x AWG) AT 20°C (in.) (lbs/1000 ft.) MINIMUM MAXIMUM (ohms/1000 ft.) 82A0111-28-* 28 42 x 44 .013 .017 71.4 .029 ± .003 1.0 82A0111-26-* 26 63 x 44 .017 .021 43.5 .033 ± .003 1.4 82A0111-24-* 24 105 x 44 .023 .027 28.2 .037 ± .003 2.1 82A0111-22-* 22 154 x 44 .029 .033 19.2 .043 ± .003 2.9 82A0111-20-* 20 154 x 42 .037 .043 11.7 .053 ± .004 4.2 82A0111-18-* 18 259 x 42 .047 .053 7.14 .064 ± .004 6.7 82A0111-16-* 16 259 x 40 .061 .067 4.53 .079 ± .004 10.2 82A0111-14-* 14 665 x 42 .078 .086 2.96 .099 ± .005 16.5 82A0111-12-* 12 665 x 40 .096 .106 1.89 .121 ± .006 24.8 82A0111-10-* 10 665 x 38 .126 .140 1.12 .157 ± .009 42.2 82A0111-8-* 8 665 x 36 .157 .173 .714 .195 ± .010 66.3 82A0111-6-* 6 1045 x 36 .192 .208 .490 .236 ± .011 102. 82A0111-4-* 4 1665 x 36 .265 .285 .326 .318 ± .013 169. 82A0111-2-* 2 1665 x 34 .325 .345 .204 .385 ± .014 252. 82A0111-1-* 1 2109 x 34 .370 .400 .163 .445 ± .019 317. 82A0111-0-* 0 2660 x 34 .435 .465 .133 .516 ± .020 407. 82A0111-00-* 00 3325 x 34 .485 .515 .102 .566 ± .020 502. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. Redwood City, CA 94063-3800 Page 1 of 2 Phone: 1-800-227-8816 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. Fax: 1-650-361-6297 REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2013 Tyco Electronics Corporation,. All rights reserved. Revision SCD Number Page 2 of 2 T SPECIFICATION CONTROL DRAWING 82A0111 TABLE II. PERFORMANCE DETAILS BEND TESTING PART NUMBER MANDREL DIAMETER WEIGHT 1/ (inch) (± 3%) (lb) (± 3%) CROSSLINKING PROOF TEST CROSSLINKING PROOF TEST 82A0111-28-* .250 .125 82A0111-26-* .375 .125 82A0111-24-* .375 .250 82A0111-22-* .500 .375 82A0111-20-* .500 .500 82A0111-18-* .500 .500 82A0111-16-* .750 .750 82A0111-14-* 1.00 1.00 82A0111-12-* 1.50 1.50 82A0111-10-* 2.00 1.50 82A0111-8-* 3.00 2.00 82A0111-6-* 3.00 2.00 82A0111-4-* 4.00 2.50 82A0111-2-* 6.00 3.00 82A0111-1-* 8.00 4.00 82A0111-0-* 8.00 4.00 82A0111-00-* 8.00 4.00 WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C SECANT MODULUS: (Test per ASTM D 882) 4 2 Maximum continuous conductor temperature AWG 28-10: 5.0 x 10 lbf/in (maximum) 4 2 VOLTAGE RATING: 600 volts (rms) at sea level AWG 8-00: 4.0 x 10 lbf/in (maximum) COLOR: White preferred 2% strain, 2 inch jaw separation, 0.2 inch/minute CONCENTRICITY: 70% (minimum) SHRINKAGE: 150 ± 3°C for 6 hours, CROSSLINKING PROOF TEST: 300 ± 3°C for 7 hours AWG 28-10: 0.13 in. (maximum) in 12 inches IDENTIFICATION AND COLOR STRIPING DURABILITY: AWG 8-00: 0.25 in. (maximum) in 12 inches 125 cycles (250 strokes) (minimum), 500 gram weight VOLTAGE WITHSTAND (Post Environmental): 2500 volts (rms), 60 Hz INSULATION ELONGATION AND TENSILE STRENGTH: AWG 28-26: Elongation, 75% (minimum) Tensile Strength, 3000 lbf/in² (minimum) PART NUMBER: AWG 24-10: Elongation, 75% (minimum) The “*” in the part numbers in Tables I and II shall be replaced by a Tensile Strength, 3500 lbf/in² (minimum) color code designator. AWG 8-00: Elongation, 125% (minimum) 1/ Example: AWG 12, white; 82A0111-12-9 Tensile Strength, 3000 lbf/in² (minimum) AWG 12, white with a black stripe; 82A0111-12-90 INSULATION FLAWS: Spark Test, 1.5 kV (rms) at 3 kHz 1/ See footer section on page 1 Impulse Dielectric Test, 6.0 kV (peak) INSULATION THICKNESS: AWG 28-16: .004 in. (minimum) AWG 14-10: .006 in. (minimum) AWG 8-00: .012 in. (minimum)