TE CONNECTIVITY 82A6013-2

82A6013 SPECIFICATION CONTROL DRAWING TITLE Date Revision WIRE, RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE-INSULATED, 8-4-10 D NORMAL WEIGHT, GENERAL PURPOSE, 600 VOLT This specification sheet forms a part of the latest issue of Raychem Specification 80. JACKET - RADIATION-CROSSLINKED, CONDUCTOR - NICKEL-COATED COPPER MODIFIED FLEXIBLE ETFE COLOR - WHITE BRAID - NOMEX BRAID TREATED PRIMARY INSULATION - RADIATION-CROSSLINKED, TO PREVENT FRAYING MODIFIED FLEXIBLE ETFE COLOR - WHITE COLOR - LIGHT GREEN TABLE I. CONSTRUCTION DETAILS DIAMETER OF FINISHED WIRE STRANDED WIRE CONDUCTOR MAXIMUM PART NUMBER MAXIMUM CONDUCTOR SIZE STRANDING RESISTANCE DIAMETER 1/ (in.) WEIGHT (AWG) (number x AWG) AT 20°C (in.) (lbs/1000 ft.) MINIMUM MAXIMUM (ohms/1000 ft.) 82A6013-8 8 665 x 36 .157 .173 .714 .245 ± .008 81.2 82A6013-6 6 1045 x 36 .192 .208 .490 .292 ± .010 123. 82A6013-4 4 1665 x 36 .265 .285 .326 .374 ± .010 196. 82A6013-2 2 1665 x 34 .325 .345 .204 .447 ± .016 291. TABLE II. PERFORMANCE DETAILS BEND TESTING PART NUMBER MANDREL DIAMETER WEIGHT 1/ (inch) (± 3%) (lb) (± 3%) CROSSLINKING PROOF TEST CROSSLINKING PROOF TEST 82A6013-8 3.00 4.00 82A6013-6 4.00 4.00 82A6013-4 5.00 4.00 82A6013-2 6.00 6.00 Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. The TE logo, Tyco Electronics and Raychem are trademarks. Raychem Wire & Cable NOMEX is a registered trademark of E.I. du Pont de Nemours and Company 501 Oakside Avenue Redwood City, CA 94063-3800 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. Page 1 of 2 Phone: 1-800-227-8816 Fax: 1-650-361-6297 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2010 Tyco Electronics Corporation. All rights reserved. Revision SCD Number Page 2 of 2 D SPECIFICATION CONTROL DRAWING 82A6013 WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 200°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level CONCENTRICITY: 70% (minimum) CROSSLINKING PROOF TEST: 300 ± 3°C for 7 hours INSULATION ELONGATION AND TENSILE STRENGTH: Elongation, 125% (minimum) Tensile Strength, 3000 lbf/in² (minimum) INSULATION FLAWS: Primary Insulation, Spark Test, 1.5 kV (rms) at 3 kHz Impulse Dielectric Test, 6.0 kV (peak) Finished Wire, Spark Test, 3.0 kV (rms) at 3 kHz Impulse Dielectric Test, 8.0 kV (peak) INSULATION THICKNESS: AWG 8-4: .008 in. (minimum) for primary insulation .012 in. (minimum) for outer jacket AWG 2: .010 in. (minimum) for primary insulation .015 in. (minimum) for outer jacket SECANT MODULUS: (Test per ASTM D 882) 4 2 4.0 x 10 lbf/in (maximum), 2% strain, 2 inch jaw separation, 0.2 inch/minute SHRINKAGE: 200 ± 3°C for 6 hours, 0.25 in. (maximum) in 12 inches VOLTAGE WITHSTAND (Post Environmental): 2500 volts (rms), 60 Hz PRODUCT IDENTIFICATION: Braid shall be marked in a contrasting color at 12 inch (nominal) intervals as follows: “ 82A6013-AWG 06090 “ 1/ See footer section on page 1