TE CONNECTIVITY ACW0219-0.75-4(BP)

ACW0219 Issue 11 Specification Control Drawing 12th March 2015 Page 1 of 2 Page 2 is for internal use only WIRE, MODIFIED FLUOROPOLYMER INSULATED, T4 (3000 Hours @ 150°C) 50 VOLT, LIGHTWEIGHT The complete requirements for procuring the wire described herein shall consist of this document and the issue in effect of Raychem Specification WSD 1223 Insulation - Radiation Crosslinked, Modified, Polyalkene Blend Conductor - Jacket - Bare Copper Radiation Crosslinked Modified PVF² C9 C11 C14 C16 C17 C18 FINISHED WIRE Part Max ConductorimumConductor Number Cross Conductor Diameter Conductor Overall Diameter (mm) Approximate Copper Sectional Stranding (mm) Resistance Insulation Lower Upper Weight Per Weight Area No./diam. @20°C (ohms/km) Thickness Spec Target Spec Unit Length Information Min. (mm) Limit Limit (kg/km) (mm²) (mm) Max. Min. Max. only (g/m) ACW0219-0.35-* 0.35 7/0.26 0.80 47.8 52.0 0.20 1.2 1.3 1.4 4.5 3.05 ACW0219-0.50-* 0.50 19/0.19 1.00 34.1 37.1 0.22 1.4 1.5 1.6 6.0 4.40 ACW0219-0.75-* 0.75 19/0.23 1.20 22.7 24.7 0.24 1.7 1.8 1.9 9.4 6.50 ACW0219-1.00-* 1.00 19/0.26 1.35 17.0 18.5 0.24 1.9 2.0 2.1 11 8.50 ACW0219-1.50-* 1.50 19/0.32 1.70 11.7 12.7 0.24 2.2 2.3 2.4 16 12.6 ACW0219-2.50-* 2.50 19/0.41 2.15 7.00 7.60 0.28 2.7 2.85 3.0 25 21.0 ACW0219-4.0-* 4.00 61/0.29 2.50 4.42 4.70 0.32 3.4 3.55 3.7 40 36.0 ACW0219-6.0-* 6.00 61/0.36 3.02 2.91 3.10 0.32 4.0 4.15 4.3 61 54.0 ACW0219-10.0-* 10.0 91/0.38 4.00 1.70 1.82 0.48 5.5 5.75 6.0 104 95.0 COLOUR CODE: The '*' in the part number shall be replaced by a standard numerical colour code designator. Additional number after base colour indicates stripe. e.g. ACW0219-0.50-96 White base colour with blue stripe. Where stripes are required, the wire carries two co-extruded longitudinal stripes of the same colour. The individual stripe width is a minimum of 10% of the wire circumference with an overall stripe coverage of 30% maximum Co-extruded longitudinal stripes are not available on gauge size 10.0 mm. ADDITIONAL Insulation Flaws: TESTING: 100% Spark Test on Finished wire of 5.0 kV High Frequency AC RMS or equivalent. MARKING All wire to be marked, with the following exceptions, Wire for: REQUIREMENTS: component use, Spooling instruction S50 and SMP-SP. Frequency of mark: Repeat mark along length of wire at a distance of 165 mm between the start of one mark and the start of another. Colour of mark: □ All black base products regardless of stripe colour are to be marked using white ink. □ All other base colours except black regardless of stripe colour are to be marked using black ink. MARK DETAIL: NOT TO SCALE 165mm APPROVAL: Electronic approval - no signatures will appear. Tyco Electronics UK Ltd Registration Number: 550926 This drawing and the information set forth hereon are the property of TE This specification sheet takes precedence over documents referenced Faraday Road London, England Connectivity UK Ltd, and are to be held in trust and confidence. Publication, herein. As TE Connectivity UK Ltd. reserve the right to make changes in Dorcan duplication, disclosure or use for any purpose not expressly authorised in writing construction without notice please contact TE Connectivity UK Ltd to ensure SWINDON by TE Connectivity UK Ltd is prohibited. that this document is the latest issue. SN3 5HH Tel: (01793) 528171 Telex: 449409 ©2015 Tyco Electronics Corporation, a TE Connectivity Ltd. Company. All Rights Reserved