Catalog 1308242 Issued 3-03 P&B CG series CMOS IC Time Delay Relay • Repeatability to .05% • Choice of timing modes – Delay on operate – Delay on release – Interval on • Knob adjustable • 10A output relay with DPDT contacts • Various models time from 0.5 sec. to 100 min. File E22575 File LR15734 Users should thoroughly review the technical data before selecting a product part number. It is recommended that user also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application. Timing Modes Contact Data @ 25°C Arrangements: 2 Form C (DPDT). Delay on operate – Delay period begins when input voltage is applied. At Material: Silver-cadmium oxide alloy. the end of the delay period, the relay will operate and will not release until Rating: 10A @ 30VDC or 277VAC, resistive; 1/2 HP @ 250VAC; input voltage is removed. Reset occurs when input voltage is reapplied. 1/3 HP @ 120VAC. Expected Mechanical Life: 10 million operations. INPUT ON Expected Electrical Life: 100,000 operations, min., at rated load. VOLTAGE OFF ➛N.O. RELAY ON TIME➛ CONTACTS OFF Initial Dielectric Strength Between Open Contacts: 500V rms, 60 Hz. Delay on release – Input voltage must be applied continuously to operate Between All Other Conductors: 500V rms, 60 Hz. the internal relay. When the control switch is closed, the relay energizes. When the control switch is opened, timing begins. When timing is complete, the relay will de-energize. Time may be reset to zero during timing by closing the control switch. CONTROL ON SWITCH OFF Input Data @ 25°C ➛N.O. RELAY ON Voltage: 120VAC and 24VDC. TIME➛ CONTACTS OFF Power Requirement: AC Types: Typically less than 3 VA. DC Types: Typically less than 3 W. Transient Protection: Yes. Reverse Voltage Protection: Yes. Interval on – The relay energizes and timing begins when input voltage is Input Voltages & Limits @25°C applied. At the end of the time delay period the relay will de-energize. Voltage Nominal Minimum Maximum Reset is accomplished by removing, then reapplying, the input voltage. Type Voltage Voltage Voltage AC 120 105 130 DC 24 20 32 INPUT ON VOLTAGE OFF Note: DC voltage must be filtered (5% p-p ripple max. at nom. voltage). AC models will operate on 50 or 60 Hz. ➛N.O. RELAY ON TIME➛ CONTACTS OFF Environmental Data Temperature Range: Storage: -40°C to +85°C. Timing Specifications Operating: -10°C to +55°C. Timing Ranges: From 0.5 to 5.0 sec. through 10 to 100 min. Timing Adjustment: Knob adjustable. Tolerance (for AC units add ±1/2 cycle 60 Hz.): Knob Adj. Types:–0, +10% of max. specified at high end of timing range; Mechanical Data +0, –10% of min. specified at low end. Termination: 8- or 11-pin octal style plug. Delta Time (for AC units add ±1 cycle 60 Hz.): ±2%, typ.; ±5%, max. Repeatability (including first cycle of operation): Enclosure: Yellow plastic case. Knob adjustable types have dial scale for reference only. AC: ±0.1%, typ.; ±0.5%, max.; but not less than ±16 ms. DC: ±0.05% typ.; ±0.1% max.; but not less than ±3 ms. Sockets: Models with 8-pin base fit either 27E122 or 27E891 (snap-on) screw terminal sockets. 11-pin types fit either 27E123 or Release Time: 30 ms, typ.; 45 ms, max. Recycle Time: AC: 40 ms, typ.; 60 ms, max. 27E892 (snap-on) screw terminal sockets. Weight: 8 oz. (227g) approximately. DC: 30 ms, typ.; 45 ms, max. Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com reference purposes only. (millimeters) unless otherwise subject to change. Technical support: 1220 specified. Refer to inside back cover. Catalog 1308242 Issued 3-03 P&B Ordering Information – Authorized distributors are more likely to stock boldface items listed below. Delay on Operate Models Delay on Release Models Voltage Time Adjustment Wiring Dia. Part Number Voltage Time Adjustment Wiring Dia. Part Number 0.5 to 5 Min. CGB-38-70005M 120VAC 1 to 10 Min. Knob 2 CGB-38-78010M 120VAC 1 to 10 Min. Knob 1 CGB-38-70010M 5 to 50 Min. CGB-38-78050M 5 to 50 Min. CGB-38-70050M 10 to 100 Min. CGB-38-70100M Interval on Models 24VDC 5 to 50 Min. Knob 1 CGD-38-30050M Voltage Time Adjustment Wiring Dia. Part Number 120VAC 0.5 to 5 Sec. Knob 1 CGB-38-79005S 1 to 10 Min. CGB-38-79010M 24VDC 1 to 10 Min. Knob 1 CGD-38-39010M Outline Dimensions ➛ 2.406 MAX. (61.1) ➛ ➛➛➛2.937 MAX. .56 1.781 MAX. .60 ➛➛➛(45.2) (74.6) (14.2) (15.2) Wiring Diagrams – Bottom Views (pins numbered clockwise from keyway) ➛➛➛➛ ➛➛➛➛ EXT. CONT. _ _ + + INPUT INPUT SW* (DC POLARITY INDICATED) (DC POLARITY INDICATED) Fig.2 Fig.1 11 Pin 8 Pin * If control switch is closed when power is applied, relay will immediately energize. A 50 millisecond minimum switch closure is required. IMPORTANT: a dry circuit switch is recommemded. A “dry circuit” switch is one rated to reliably switch currents of less than 50mA. Use of a switch rated for other than dry circuit may result in failure of the time delay relay to function properly. ** Note: input polarity for DC operation. For most reliable operation on AC, connect high side to “+” and low side to “–”. Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com reference purposes only. (millimeters) unless otherwise subject to change. Technical support: 1221 specified. Refer to inside back cover.