TE CONNECTIVITY D-436-85

CUSTOMER DRAWING MATERIALS 1. INSULATION SLEEVE: Heat-shrinkable, transparent blue, radiation cross-linked modified polyvinylidene flouride. 2. SINGLE-WIRE SEAL: Low outgassing immersion resistant thermoplastic fluoroelastomer. Color: BLUE. 3. INTEGRAL-WIRE SEAL: Low outgassing immersion resistant thermoplastic fluoroelastomer. Color: BLUE. 4. CRIMP SPLICE: Base Metal: Copper Alloy 101 or 102 per ASTM B-75. Plating: Nickel per QQ-N-290. Dimensions: Part Prod. Crimp Splice Name Rev. Size ØB ØC D E Color Code D-436-85 A 20 1.27 (0.050) 2.03 (0.080) 12.95 (0.510) 6.22 (0.245) Red 1.14 (0.045) 1.91 (0.075) 12.45 (0.490) 5.72 (0.225) D-436-86 B 16 1.75 (0.069) 2.70 (0.106) 14.86 (0.585) 7.11 (0.280) Blue 1.63 (0.064) 2.57 (0.101) 14.35 (0.565) 6.60 (0.260) D-436-87 A 12 2.60 (0.102) 3.91 (0.154) 14.86 (0.585) 7.11 (0.280) Yellow 2.46 (0.097) 3.73 (0.147) 14.35 (0.565) 6.60 (0.260) Installation Data: Wire Size Range of Crimp Splice Splicer One Wire Two wires Three wires Size Minimum Maximum Minimum Maximum Minimum Maximum 20 24 20 26 24 28 24 16 20 16 24 20 24 22 12 16 12 22 16 22 18 TITLE : (Low Outgassing) Raychem IN-LINE SPLICE SEALING SYSTEM, Devices 2 OR 3 TO 1 SPLICER: Nickel Plated, Color Coded, with Inspection Slots UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS. DOCUMENT NO. : INCHES DIMENSIONS ARE BETWEEN BRACKETS. D-436-85/-87 TE CONNECTIVITY (TE) RESERVES THE RIGHT TO TOLERANCES: ANGLES: N/A DATE: REVISION: CHANGE THIS DRAWING AT ANYTIME. USER 0.00 N/A June 16, 2017 SHOULD EVALUATE THE SUITABILITY OF THE B2 0.0 N/A ROUGHNESS IN PRODUCT FOR THEIR APPLICATION. 0 N/A MICRON DRAWN BY: ECO APPROVED: ECO NUMBER: SCALE: SIZE: SHEET: M. FORONDA L. RODRIGUEZ ECO-17-008496 None A 1 of 2 ©2015-2017 TE CONNECTIVITY CORPORATION. ALL RIGHTS RESERVED. If this document is printed it becomes uncontrolled. Check for the latest revision. CUSTOMER DRAWING APPLICATION 1. These parts are designed to provide an immersion resistant in-line splices of 2 or 3 to 1 wires falling within the size range listed on sheet 1, having insulations rated for at least 135C. 2. Parts are available only as an assembly of one of each Item #1 and Item #2. 3. Parts are to be installed per Thermofit Assembly Procedure, see below. 4. Inside diameter and outside diameter of splice are to be measured in crimp areas, 2.54 to 5.08 (0.100 to 0.200) from ends of part. Slight burr permitted on parted surfaces. 5. Acceptance sampling shall be in accordance with Paragraph 4.6.1 of MIL-T-7928. 6. Packing and packaging shall be in accordance with Section 5, Level C, of MIL-T-7928. 7. This document takes precedence over documents referenced herein. THERMOFIT ASSEMBLY PROCEDURE 1.0 SCOPE This document outlines the procedure to be followed to obtain immersion resistant 3 or 2 to 1 in-line splices using Thermofit In-Line Splice Sealing System D-436-85/-87. 2.0 PROCEDURE: a) Strip all wires 7.92 (0.312) to 8.74 (0.344). b) Attach the single lead to the appropriate size crimp splice using a Raychem AD-1377 Crimp Tool. c) Pass the wires to be attached to other barrel through the sealing sleeve from the three hole insert end. d) Insert wires into barrel and crimp. Care must be taken so that the wires remain untwisted between the crimp splice and the three wire seal or the sealing sleeve cannot be positioned properly. e) Apply heat, using a recommended heat source, first to the three-hole insert and then to the other. Heat should be applied until insert melts and flows axially along the wire. 3.0 RECOMMENDED RAYCHEM HEATING TOOLS HEATER REFLECTOR RECOMMENDED TEMPERATURE SETTING Steinel HL-2010E 832011-000 316ºC-371ºC (600ºF-700ºF) Thermogun #500A TG-14 316ºC-371ºC (600ºF-700ºF) Shop Air Heater #CV-4504 991180-000 316ºC-371ºC (600ºF-700ºF) Mini-Gun #CV-5300 991319-000 316ºC-371ºC (600ºF-700ºF) TITLE : (Low Outgassing) Raychem IN-LINE SPLICE SEALING SYSTEM, Devices 2 OR 3 TO 1 SPLICER: Nickel Plated, Color Coded, with Inspection Slots UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS. DOCUMENT NO. : INCHES DIMENSIONS ARE BETWEEN BRACKETS. D-436-85/-87 TE CONNECTIVITY (TE) RESERVES THE RIGHT TO TOLERANCES: ANGLES: N/A DATE: REVISION: CHANGE THIS DRAWING AT ANYTIME. USER 0.00 N/A June 16, 2017 SHOULD EVALUATE THE SUITABILITY OF THE B2 0.0 N/A ROUGHNESS IN PRODUCT FOR THEIR APPLICATION. 0 N/A MICRON DRAWN BY: ECO APPROVED: ECO NUMBER: SCALE: SIZE: SHEET: M. FORONDA L. RODRIGUEZ ECO-17-008496 None A 2 of 2 ©2015-2017 TE CONNECTIVITY CORPORATION. ALL RIGHTS RESERVED. If this document is printed it becomes uncontrolled. Check for the latest revision.