TE CONNECTIVITY FL2500-NO.1-I8-0-101MM

FL2500 Fully flame-retardant, adhesive-lined, polyolefin heat-shrinkable tubing FL2500 dual wall tubing comprises FL2500 with its high-performance FL2500 is available in a comprehensive a tough crosslinked, flame-retardant, adhesive lining offers an economical range of sizes to meet most polyolefin tubing lined with a new and highly-effective method for permanently component sealing requirements, flame-retardant adhesive to provide sealing and protecting splices, fusible and is compatible with a wide range the optimum solution for applications links, terminals, and in-line components. of application equipment. where full retardancy is preferred, or As the tubing is heated and shrinks specified. Rated to 135°C for 3000 down onto its substrate, the adhesive hours, it is suitable for use in the lining melts and flows to fill all voids automotive harness market and other and create a complete seal against harsh environments. moisture, oils, chemicals, etc. Temperature rating Full recovery temperature: 135°C Continuous operating temperature –40°C to 135°C Specifications* Type Raychem FL2500 FL2500 SCD *When ordering, always specify latest issue. Dimensions (millimeters/inches) Expanded as supplied W1 Fully recovered after heating D d W Inside diameter (including core) Recovered wall thickness** D (min.) d (max.) W W1 (min.) Expanded Recovered after Total Adhesive Size as supplied heating wall wall NO. 1 7.62 0.300 1.65 0.065 1.52 ± 0.3 0.060 ± 0.012 0.711 0.028 NO. 2 9.02 0.355 2.29 0.090 1.52 ± 0.3 0.060 ± 0.012 0.711 0.028 NO. 3 11.56 0.455 2.54 0.100 2.29 ± 0.3 0.090 ± 0.012 1.321 0.052 NO. 4 17.79 0.700 4.45 0.175 2.54 ± 0.3 0.100 ± 0.012 1.346 0.053 **Wall thickness will be less if tubing recovery is restricted during shrinkage. Ordering information Color Black with a white adhesive liner Size selection Consult manufacturer’s recommended size selection guidelines. Standard packaging Cut pieces. See reverse for standard cut lengths. Marking Tubing will be marked with the number size (for example, FL-1, FL-2, FL-3, FL-4). Ordering description Specify product name, size, color, and cut length; for example, FL-2500-No. 2-0-50mm (0=Black). Specification values Property Unit Requirement Method of test Material Dimensions mm (inches) See reverse ASTM D 2671 Longitudinal change percent +0, -10 ASTM D 2671 Tensile strength* psi 1500 minimum ASTM D 2671 Speed 2 in./min. Ultimate elongation percent 300 minimum ASTM D 2671 Speed 2 in./min. Secant modulus* psi 35,000 minimum ASTM D 2671 (expanded form) Concentricity percent 60 minimum ASTM D 2671 (expanded form) Dielectric strength volts/mil 500 minimum ASTM D 149 (jacket only)** 13 Volume resistivity ohm-cm 10 minimum ASTM D 257 Flammability Self-extinguishing SAE J1128 within 30 seconds See note below Heat shock No dripping, flowing, or ASTM D 2671 4 hours at 250°C cracking of jacket Splice performance Immersion leak resistance micro-amps 0.25 maximum See note below Thermal cycling See note below 5 cycles, 5°C to 130°C Followed by test for: Immersion leak resistance micro-amps 0.25 maximum Thermal aging See note below 168 hours at 130°C Followed by test for: Immersion leak resistance micro-amps 0.25 maximum Fluid resistance See note below 24 hours at 25°C ± 3°C in: ASTM Reference Fuel C VV-F-800 Diesel Fuel 1 hour at 100°C ± 3°C in: ASTM #3 Oil Followed by test for: Immersion leak resistance micro-amps 0.25 maximum *Calculate based on wall thickness of jacket only. **Remove adhesive manually prior to testing. Note: Consult the FL2500 SCD for specific details about test procedures. Standard cut lengths Part number Standard cut length Cut length tolerance FL2500-No. 1 27mm, 50 mm, 65 mm ± 1.5 mm 1220 mm ± 25.4 mm FL2500-No. 2 27mm, 50 mm, 65 mm ± 1.5 mm 1220 mm ± 25.4 mm FL2500-No. 3 27mm, 65 mm, 75 mm ± 1.5 mm 1220 mm ± 25.4 mm FL2500-No. 4 27mm, 75 mm, 90 mm ± 1.5 mm 1220 mm ± 25.4 mm Raychem and FL2500 are trademarks of Tyco Electronics Corporation. Users should independently evaluate the suitability of the product for their application. Tyco Electronics Corporation 300 Constitution Drive Faraday Road 3816 Noborito, Tama-ku Asia Pacific Headquarters Menlo Park, CA 94025-1164 Dorcan, Swindon, SN3 5HH Kawasaki, Kanagawa 214-8533 26 Ang Mo Kio, Industrial Park 2 USA United Kingdom Japan Singapore 569507 Tel:(800) 926-2425 (US & Canada) Tel: +44 1793 528171 Tel: +81 44 900 5102 Tel: +65 4866 151 Tel:+1 (650) 361-3860 (All other countries) All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics Corporation makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics Corporation’s only obligations are those in the Standard Terms and Conditions of Sale for these products and in no case will Tyco Electronics Corporation be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the product. Tyco Electronics Corporation’s Specifications are subject to change without notice. In addition, Tyco Electronics Corporation reserves the right to make changes in materials or processing without notification to the Buyer which do not affect compliance with any applicable specification. For more information about this product visit www.tycoelectronics.com © 2002, 2006 Tyco Electronics Corporation Printed in USA 1654058 rev 7/06