TE CONNECTIVITY T75S5D112-48

200 W 100 W 50 W 25 W General Purpose Catalog 1308242 Low Power PCB Relays Potter & Brumfield Issued 3-03 (PDF Revised 8-06) P&B Sensitive, Low Profile, Hi-Current Low profile, PCB Relay T75 Series Relay Designed to Meet International Standards T75 series n 1 pole 8A, 1 form C (CO) or 1 form A (NO) contact n 4kV/8mm coil-contact 10 Amp, PC Board n Reinforced insulation (protection classII) Miniature Relay n Ambient temperature up to 85°C at 8A File E29244 n Plastic materials according to IEC60335-1 (domestic appliances) File No. 3919 Users should thoroughly review the technical data before selecting a product part number. It Typical applications is recommended that user also seek out the pertinent approvals files of the agencies/ HVAC,security and industrial control, domestic appliances. laboratories and review them to ensure the product meets the requirements for a given application. Z Features Initial Dielectric Strength Approvals Coil Data • High sensitivity – nominal coil power requirement is as low as 212mW. Between Open Contacts: 1,000V rms. 2 2 Coil voltage range 3 to 60VDC • Low profile, .591 in. (15mm) tall case uses only .465 in (3cm ) of area on the Between Contacts and Coil: 4,000V rms, 8mm. VDE Cert. No. 3919, UL E214025 Operative range, IEC 61810 2 Technical data of approved types on request. printed circuit board, permitting high density circuit design. Coil insulation system according UL classA • Power switching capability – contacts rated 10 amps in 1 Form A (SPST-NO) or 1 Coil versions, DC coil Form C (SPDT) arrangements. Coil Rated Operate Release Coil Rated coil Contact Data • Designed to meet UL, CSA, VDE, SEMKO and SEV requirements. code voltage voltage voltage resistance power Contact arrangement 1 form C (CO) or 1 form A (NO) • Designed to meet VDE 8mm spacing, 4kV dielectric, coil to contacts. 1) VDC VDC VDC Ω±10% mW Coil Data Rated voltage 250VAC • Designed to meet 3 mm creepage between contacts. 03 3 2.1 0.3 40 225 Max. switching voltage 400VAC • Conforms to: VDE 0110 – Insulation Group C (250V) Voltage: 3 to 60VDC. 05 5 3.4 0.5 118 212 Rated current 8A VDE 435 Part 201 – High current applications Maximum Power @ 23°C: 1W. 06 6 4.1 0.6 165 218 Limiting making current, max 4s, df 10% 15A VDE 0804 – Telecommunications equipment Nominal Power @ 23°C: 230mW, typ. 09 9 6.1 0.9 364 223 Breaking capacity max. 2000VA VDE 0631 – Temperature controllers and limiters Temperature Rise: 85C° per Watt. 12 12 8.2 1.2 652 221 Contact material AgCdO VDE 0700 – Household appliances Duty Cycle: Continuous. 24 24 16.3 2.4 2270 254 Min. recommended contact load 100mA at 12VDC VDE 0805/5.90 – Office machines 48 48 32.6 4.8 8790 262 Minimum switching voltage 5VDC 1) • Wash tight (washable). 60 60 40.8 6.0 15265 236 Initial contact resistance 100mΩ at 100mA, 12VDC -1 • Well suited for a broad range of applications e.g. HVAC, appliances, 1) Coil resistance ±15%. Frequency of operation, with/without load 6/1200min Coil Data All figures are given for coil without pre-energization, at ambient temperature +23°C. security and industrial control. Operate/release time max. 10/5ms Other coil voltages on request. DC Must Nominal Bounce time max., form A/form B 3/10ms Nominal Resistance Operate Coil Insulation Data Voltage in Ohms Voltage Current Electrical endurance ±10% (mA) Contact Ratings @ 25°C with relay properly vented. Type Contact Load Cycles 3 T75 8Arms, 240VAC, resistive 100x10 Remove vent nib after soldering and cleaning. 3 40 2.1 75.0 3 T75 A (NO) 14Arms, 120VAC, resistive 50x10 5 118 3.4 42.4 Arrangements: 1 Form A (SPST-NO) and 1 Form C (SPDT). 3 T75 B (NC) 5Arms, 120VAC, resistive 50x10 6 165 4.1 36.4 Material: Silver-cadmium oxide. 3 T75 7.2 FLA / 45 LRA, 120 VAC 30x10 DC 9 365 6.1 24.7 Expected Mechanical Life: 10 million operations. 3 T75 5 FLA / 30 LRA, 240 VAC 10x10 Coils 12 650 8.2 18.5 Expected Electrical Life: 18 1,455 12.3 12.4 100,000 operations at 8 amps, 240VAC. Contact ratings 24 2,270 16.3 10.6 50,000 operations at 14 amps NO / 5 amps NC, 120VAC Res. Type Contact Load Cycles 36 5,460 24.5 6.4 30,000 operations at 7.2 FLA, 45 LRA, 120VAC. 3 T75 A (NO) TV4, Tungsten, 120VAC, 40°C 25x10 48 8,790 32.6 5.5 10,000 operations at 5 FLA, 30 LRA, 240VAC. 3 T75 C (CO) 10A, 240VAC, general purpose, 40°C 6x10 60 15,265 40.8 3.9 3 30,000 operations at B300 pilot duty (360VA, 240VAC; 470VA, 120VAC). T75 C (CO) 8A, 24VDC, general purpose, 40°C 100x10 3 Contact Ratings (See Figure 1): T75 C (CO) 1/3HP, 120VAC, 40°C 30x10 3 Maximum Switched Voltage: 380VAC. T75 C (CO) 1/2HP, 240VAC, 40°C 30x10 Maximum Switched Current: 14/5 (N.O./N.C.) amps, AC resistive; 6 8 amps DC (see Fig. 1) Mechanical endurance, DC coil 10x10 operations Maximum Switched Power: 200W, DC; 2,000VA, AC. Operate Data @ 23°C Minimum Required Contact Load: 12V, 100mA. Initial dielectric strength VDE Contact Ratings: 8 amps, 250VAC. Must Operate Voltage: 70% of nom. voltage or less. between open contacts 1000V rms UL Contact Ratings: 10 amps, 240VAC; 8 amps 24VDC; Must Release Voltage: 10% of nom. voltage or more. between contact and coil 4000V rms 1/3 HP, 120VAC; 1/2 HP, 240VAC. Operate Time (Excluding Bounce): 6 ms, typ., at nom. voltage. Clearance/creepage Release Time (Excluding Bounce): 2.5 ms, typ., at nom. voltage. between contact and coil ≥8/8mm Maximum Switching Rate: 20 operations/second. Material group of insulation parts IIIa Figure 1 - DC Switching Load Limit Curve Maximum Continuous Operating Voltage: 225% of nom. voltage. 300 200 ENVIRONMENTAL DATA Temperature Range 100 Storage: -40°C to +130°C. Operating: -40°C to +85°C. 1 50 01-2015, Rev. 0115 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, 40 www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are 30 © 2015 Tyco Electronics Corporation, with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions 20 Mechanical Data Termination: Printed circuit terminals. 10 Enclosures: Wash tight (washable) case. .1 1 10 100 Weight: 0.39 oz. (11.0g) approximately. Switching Current (Amps DC) Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com reference purposes only. (millimeters) unless otherwise subject to change. Technical support: 414 specified. Refer to inside back cover. Switching Voltage (VDC) General Purpose Low Power PCB Relays Potter & Brumfield Low profile, PCB Relay T75 Series (Continued) Other Data PCB layout / terminal assignment Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at 1 form C, 1 CO contact, 3.2 mm www.te.com/customersupport/rohssupportcenter Ambient temperature - 40 to +85°C Category of environmental protection IEC 61810 RTII - flux proof RTIII - wash tight Vibration resistance (functional) form A (NO) / form B (NC) 10/4g Vibration resistance (destructive) form A (NO) / form B (NC) 20/5g Shock resistance (destructive) 100g Terminal type PCB-THT Weight 11g Resistance to soldering heat THT IEC 60068-2-20 RTIII: 260°C/5s Packaging/unit tube/20 pcs., box/1000 pcs. 1 form A, 1 NO contact, 5 mm Dimensions 1 form C, 1 CO contact, 3.2 mm 1 form A, 1 NO contact, 5 mm 2 01-2015, Rev. 0115 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2015 Tyco Electronics Corporation, with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions General Purpose Low Power PCB Relays Potter & Brumfield Low profile, PCB Relay T75 Series (Continued) Product code structure Typical product code T75 S 5 D 1 1 2 -12 Type T75 Low profile, printed circuit board relay T75 Series Enclosure S RTIII - wash tight Contact arrangement 1 1 form A, 1 NO 5 1 form C, 1 CO Coil input D DC voltage Coil Configuration 1 Single coil, monostable (non-latching) Mounting and terminals 1 PCB terminals Contact materials 2 AgCdO Coil voltage Coil code: please refer to coil versions table (e.g. 05=5VDC) Product code Arrangement Enclosure Coil Part Number T75S1D112-05 1 form A, 1 NO RTIII - wash-tight 5VDC 1393222-7 T75S1D112-06 6VDC 5-1393223-2 T75S1D112-12 12VDC 2-1393222-9 T75S1D112-24 24VDC 4-1393222-8 T75S5D112-05 1 form C, 1 CO 5VDC 7-1393222-6 T75S5D112-09 9VDC 9-1393222-0 T75S5D112-12 12VDC 1393223-3 T75S5D112-18 18VDC 1-1393223-6 T75S5D112-24 24VDC 2-1393223-8 T75S5D112-48 48VDC 4-1393223-1 T75S5D112-60 60VDC 1423089-1 3 01-2015, Rev. 0115 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2015 Tyco Electronics Corporation, with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions