shrinkHOoP Cable Clamp Heat Shrink Grommet Sizes 2, 3 and 4 c b a L Table of Dimensions, inch (mm): Inside Diameter Outside Diameter Overall Length Part Recovered Recovered Description Min. Exp. (a) Max. Rec’d (b) (c), Ref L, Ref (See Note*) URHR-2 1.23 (31) 0.10 (2.5) 0.375 (9.5) 0.50 (13) URHR-3 1.44 (37) 0.14 (3.5) 0.500 (12.7) 0.50 (13) URHR-4 1.85 (47) 0.18 (4.6) 0.562 (14.2) 0.75 (19) Note*: Alternate lengths available upon request. Material: heat shrinkable, cross linked polyolefin, meets MIL-I-81765/1 Type II with Shore Hardness value 35+/- 5. Color: Black shrinkHOoP is a Trademark of Tyco Electronics Specification Control Drawing Tyco Electronics Corporation Title: 300 Constitution Drive shrinkHOoP –Cable Clamp Heat Menlo Park, CA 94025 USA Shrink Grommet Sizes 2, 3 and 4 Tyco Electronics reserves the right to amend this drawing at any time. Document No. Users should evaluate the suitability of the product for their application. URHR-2-thru-4 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES. Rev.: Rev. Date: METRIC DIMENSIONS ARE SHOWN IN BRACKETS F December 9, 2004 DRAWN BY: CAGE CODE: Org. Date: File name: SCALE: SIZE: SHEET: U.NGUYEN 06090 10/03/2001 R040891 None A 1 of 2 ©2004 Tyco Electronics Corporation. All rights reserved If this document is printed it becomes uncontrolled. Check for the latest revision. Table 2: Properties Property Requirements Test method Physical Tensile strength 1200 psi (8.3 Mpa) minimum ASTM D-412 Ultimate elongation 250% minimum ASTM D-412 Specific gravity 1.4 maximum ASTM D-792 Water absorption 0.5% maximum ASTM D-570 Hardness, Shore D 35 ± 5 ASTM D-2240 Flammability Pass ASTM D-635 Pass FAR-25 Corrosion resistance Pass MIL-I-81765 Low temperature flex Pass MIL-I-81765 4 hours at –67 ± 2°F (-55 ± 1°C) Heat resistance 200% ultimate elongation, MIL-I-81765 168 hours at 347 ± 2°F minimum (175 ± 1°C) 1000 psi (6.9 Mpa) tensile strength, minimum Heat shock No cracking, dripping or flowing MIL-I-81765 4 hours at 437 ± 5°F (225 ± 2°C) Elastic Memory 275% minimum expansion to 4 inch (10 cm) of a fully recovered test specimen, and 93% recovery of expanded specimen after oven condition for 1 minute at 302 ± 4°F (150 ± 2° C) Dielectric strength 200 v/mil (7880 v/mm) minimum ASTM D-149 Electrical 12 Volume resistivity 10 ohm-cm minimum ASTM D-257 Chemical 200% ultimate elongation, MIL-I-81765 minimum Fluid Resistance 750 psi (5.2 Mpa) tensile strength, minimum shrinkHOoP is a Trademark of Tyco Electronics Specification Control Drawing Rev. Date: Rev.: Document No. Sheet: Dec. 9, 2004 F 2 of 2 URHR-2-thru-4 If this document is printed it becomes uncontrolled. Check for the latest revision.