TE CONNECTIVITY V23072A1062A303

Automotive Relays PCB Relays Mini Relay K (Open – Sealed) n Limiting continuous current 20A n 24VDC coil versions available Typical applications Car alarm, hazard warning signal, heated rear screen, immobilizer, lamps front/rear, fog light, interior lights, sun roof, turn signal, wiper control. F072A/C_fcw2b Contact Data Load resistive/inductive resistive/inductive resistive/inductive head/indicator head/indicator load load load lamp lamp V23072-C10**-A302 V23072-C10**-A303 V23072-C10**-A308 V23072-C1061-A402 V23072-C1061 A408 Contact arrangement 1 form A, 1 NO 1 form C, 1 CO 1 form U/X, 2 NO 1 form A, 1 NO 1 form U/X, 2 NO Rated voltage 12VDC 12VDC 12VDC 12VDC 12VDC Rated current 15A 10/15A 2x10A 12A 2x6A Limiting continuous current 23°C 15A 10/15A 2x10A 12A 2x6A 85°C 10A 5/10A 2x6A 10A 2x5A 1)2) 3) 3) Limiting making current 60A NC/NO 12/60A 2x40A 60A 120A Limiting breaking current 20A 10/20A 2x20A 6A 12A Contact material AgNi0.15 AgNi0.15 AgNi0.15 AgSnO.2 AgSnO.2 4) Min. recommended contact load 1A at 5VDC 1A at 5VDC 1A at 5VDC 1A at 5VDC 1A at 5VDC Initial voltage drop at 10A, typ./max. 50/300mV 50/300mV 2x50/300mV 150/300mV 150/300mV 5) Operate/release time max. typ. 3/1.5ms 5 5 5 6 6 Electrical endurance >2x10 ops. >2x10 ops. >2x10 ops. >1x10 ops. >1.5 x 10 ops. at 13.5VDC, 10A at 13.5VDC, 10A at 13.5VDC, 10A up to 6x21W up to 6x21W 5 5 >1.5x10 ops. >7.5x10 ops. 100A (on), 10 A (off) 100A (on), 10A (off) high beam high beam 1) The values apply to a resistive load or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC and 27VDC for 24VDC load voltages. 2) For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) Corresponds to the peak inrush current on initial actuation (cold filament). 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes 5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding (monostable version only). Max. DC load breaking capacity Load limit curve 1: safe shutdown, connected as form X, load on pin 5 and 7. Load limit curve 2: safe shutdown, no stationary arc (NO contact). Load limit curve 3: arc extinguishes during transit time (CO contact). Load limit curves measured with low inductive resistors verified for 1000 switching events. OBSOLETE NOT the LATEST 1 02-2012, Rev. 0212 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications REVISION © 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions Automotive Relays PCB Relays Mini Relay K (Open – Sealed) (Continued) Coil Data Other Data Rated coil voltage 12VDC, 24VDC EU RoHS/ELV compliance compliant Degree of protection Coil versions, DC coil IEC 61810 RT II – open (V23072-A), Coil Rated Operate Release Coil Rated coil RT III – imm. cleanable (V23072-C) code voltage voltage voltage resistance power Climatic cycling with condensation VDC VDC VDC Ω±10% W EN ISO 6988 20 cycles, storage 8/16h 061 12 6.9 1.2 130 1.1 Temperature cycling (shock) 062 24 14.1 2.4 520 1.1 IEC 60068-2-14, Na 720 cycles, -40/+85°C (dwell time 1h) All figures are given for coil without pre-energization, at ambient temperature +23°C. Damp heat constant IEC 60068-2-3, Ca 56 days, upper air temperatue 55°C Coil operating range Corrosive gas IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional) 6) IEC 60068-2-6 (sine sweep), 10 to 200Hz, 23 to 35g Shock resistance (functional) 6) IEC 60068-2-27 (half sine), 4 to 6ms 23 to 280g Terminal type PCB Weight, open/sealed approx. 8/9g (0.28/0.32oz) Solderability (aging 3: 4h/155°C) Does not take into account IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C the temperature rise due to Sealing, IEC 60068-2-17 Qc, method 2, 1min/70°C the contact current 7) Storage conditions according IEC 600688 E = pre-energization Packaging unit open 600 pcs. sealed 504 pcs. 6) Values weekest direction. Depending on mounting position: no change in the switching state >10μs. 7) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ Does not take into account the temperature rise due to the contact current E = pre-energization. Terminal Assignment (Open and Sealed version) Bottom view on solder pins 1 form A, NO 1 form U/X, 2 NO 1 form C, CO TE1111-U1 TE1116-11 TE1077-B1 2 02-2012, Rev. 0212 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions Automotive Relays PCB Relays Mini Relay K (Open – Sealed) (Continued) Dimensions Mini Relay K Open Version Mini Relay K Sealed Version 15.0 ±1.0 13.0 ±0.2 14.5 ±0.4 The Nipp-off-pin may be 14.7 ±0.3 16.9 ±0.3 9.5 ±0.2 Assembly and removed after soldering ø 3.5 Nipp-off-pin positioning aid and washing (for ventilation) 17.5 ±0.5 0.2 – 1.4 19.2 ±0.3 0.45 ±0.4 Terminals tinned 4.0 ±1.0 Terminals tinned 0.3 ±0.2 3.5 ±0.3 *) 0.9 ±0.15 3.0 ±0.3 *) *) additional tin tops 6.1 ±0.3 TE1112-32 *) Additional tin tops max. 1 mm max. 1 mm 6.7 ± 0.3 TE0595-Z2 View of the terminals (bottom view) View of the terminals (bottom view) 1.9 ±0.2 ø0.85 ±0.05 2 x ø0.85 ±0.05 0.85 ±0.06 4.6 ±0.2 4x 0.85 ±0.06 9.0 ±0.2 0.75 ±0.06 0.55 ±0.05 0.85 ±0.06 TE2209-U2 0.85 ±0.06 0.75 ±0.06 4x 0.55 ±0.05 TE2210-X2 PCB Layout PCB Layout Bottom view on solder pins, grid 1.25 to 1.27mm Bottom view on solder pins, grid 1.25 to 1.27mm ø 1.3 +0.1 ø 1.3 +0.1 1.25 – 1.27 1.25 – 1.27 1.42 ±0.25 2.4 ±0.6 1.0 ±0.45 1.2 ±0.4 TE0596-82 2.3 max. 2.7 ±0.4 TE0598-P2 3 02-2012, Rev. 0212 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions ø2.0 ±0.1 Automotive Relays PCB Relays Mini Relay K (Open – Sealed) (Continued) Product code structure Typical product code V23072 -A 1 061 -A 30 2 Type V23072 Mini Relay K (Open – Sealed) Terminal and enclosure A PCB, open (RT II) C PCB, sealed (RT III – immersion cleanable) Design 1 Standard Coil 061 12 VDC 062 24 VDC Contact type A Standard Contact material 30 AgNi0.15 40 AgSnO 2 Contact arrangement 2 1 form A, NO 3 1 form C, CO 8 1 form U/X, 2 NO Product code Terminal/Encl. Design Coil Contact type Cont. material Arrangement Part number V23072-A1061-A303 PCB, open Single relay 12VDC Standard AgNi0.15 1 form C, CO 3-1393272-2 V23072-A1062-A303 24VDC 5-1393272-2 V23072-A1061-A308 12VDC 1 form U/X, 2 NO 3-1393272-6 V23072-A1062-A308 24VDC 5-1393272-3 V23072-C1061-A302 12VDC 1 form A, NO 4-1393273-9 V23072-C1062-A302 24VDC 7-1393273-6 PCB, sealed V23072-C1061-A303 12VDC 1 form C, CO 5-1393273-6 V23072-C1062-A303 24VDC 7-1393273-8 *) V23072-C1062-A303-EV-USBX 2-1414939-5 V23072-C1061-A308 12VDC 1 form U/X, 2 NO 6-1393273-0 V23072-C1062-A308 24VDC 8-1393273-2 8) V23072-C1061-A402 12VDC 1 form A, NO 2-1416001-0 8) V23072-C1061-A408 AgSnO 1 form U/X, 2 NO 1-1416001-4 2 *) Americas market only. 4 02-2012, Rev. 0212 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications © 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions