TRACO POWER TES1-0511TR

DC/DC Converters TES 1 Series, 1 Watt Features ◆ Small SMD package with standard footprint ◆ I/O isolation 1500 VDC ◆ Single and dual output models ◆ Input voltage 5, 12 and 24 VDC ◆ High efficiency up to 80% ◆ Operating temperature range –40°C to +90°C ◆ High accuracy of pin co-planarity ◆ Qualified for leadfree reflow solder With their small footprint these 1Watt DC/DC converters are an ideal and economi- process according IPC/JEDEC J-STD-020C cal solution for many applications where an isolated voltage is required. Typical ap- ◆ Available in tape and reel package plications are ground loop elimination, noise reduction, voltage isolation in digital interfaces and voltage conversion in distributed power systems. With a new pack- ◆ 3-year product warranty age design these converters are qualified for the higher temperatures requested by lead-free reflow solder processes. For automated SMD production lines the devices can be supplied in standard tape and reel package. Models Order code Input voltage Output voltage Output current max. Efficiency typ. TES 1-0510 3.3 VDC 300 mA 73 % TES 1-0511 5 VDC 200 mA 78 % TES 1-0519 9 VDC 110 mA 78 % 12 VDC 85 mA 78 % TES 1-0512 5 VDC ±10% (nominal 5 VDC) TES 1-0513 15 VDC 65 mA 79 % TES 1-0521 ±5 VDC ±100 mA 74 % TES 1-0522 ±12 VDC ±40 mA 78 % TES 1-0523 ±15 VDC ±35 mA 78 % TES 1-1211 5 VDC 200 mA 76 % TES 1-1219 9 VDC 110 mA 78 % TES 1-1212 12 VDC 85 mA 79 % 12 VDC ±10% TES 1-1213 15 VDC 65 mA 80 % (nominal 12 VDC) TES 1-1221 ±5 VDC ±100 mA 74 % TES 1-1222 ±12 VDC ±40 mA 78 % TES 1-1223 ±15 VDC ±35 mA 79 % TES 1-2411 5 VDC 200 mA 78 % TES 1-2419 9 VDC 110 mA 77 % TES 1-2412 12 VDC 85 mA 77 % 24 VDC ±10% TES 1-2413 15 VDC 65 mA 79 % (nominal 24 VDC) TES 1-2421 ±5 VDC ±100 mA 73 % TES 1-2422 ±12 VDC ±40 mA 78 % TES 1-2423 ±15 VDC ±35 mA 78 % http://www.tracopower.com Page 1 of 4 DC/DC Converters TES 1 Series 1 Watt Input Specifications Input current no load / full load 5 Vin models: 30 mA / 260 mA typ. 12 Vin models: 15 mA / 110 mA typ. 24 Vin models: 8 mA / 55 mA typ. Surge voltage (1 sec. max.) 5 Vin models: 9 V max. 12 Vin models: 18 V max. 24 Vin models: 30 V max. Reverse voltage protection 0.3 A max. Input filter internal capacitors Output Specifications Voltage set accuracy – 5 VDC models: ±2 % at 60 % load – other models: ±2 % at 100 % load Voltage balance (dual output models, balanced load) ±1 % max. Regulation – Input variation 1.2 % / 1 % change Vin – Load variation see graphs below Ripple and noise (20 MHz Bandwidth) 120 mVpp max. Temperature coefficient ±0.02 %/K Short circuit protection limited 0.5 sec. max. Capacitive load 33 µF max. (each output) General Specifications Temperature ranges – Operating –40°C to +90°C – Storage –50°C to +125°C – Case +105°C max. Derating (convection cooling) 3.3 %/K above +75°C Humidity (non condensing) 95 % rel. H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >2’000’000 h Isolation voltage (60sec.) – Input/Output 1‘500 VDC Isolation capacitance – Input/Output 40 pF typ. Isolation resistance – Input/Output >1‘000 Mohm Switching frequency 100 kHz typ. (frequency modulation) Frequency change over line and load ±30 % Environmental compliance – Reach www.tracopower.com/overview/tes1 – RoHS RoHS directive 2011/65/EU Output voltage variation dependent on load (at nominal input voltage) 5 VDC models: other models: +10% +10% max. max. typ. 0% 0% min. typ. min. -10% -10% 0 50% 100% 0 50% 100% Load Load All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 4 Deviation of Vout nom. Deviation of Vout nom. DC/DC Converters TES 1 Series 1 Watt Physical Specifications Casing material plastic (UL94V-0 rated) Weight single output models: 1.7 g (0.06oz) dual output models: 2.0 g (0.08oz) Lead-free reflow solder process as per J-STD-020D.1 (to find at: www.jedec.org - free registration equired) Peak package body temperature: 245°C Moisture sensivity level (MSL) level 2 as per J-STD-033B.1 (to find at: www.jedec.org - free registration required) Washing process not recommended. Product non-hermetical Packaging www.tracopower.com/products/tes1-pack.pdf Application note: www.tracopower.com/overview/tes1 Outline and Solder Pad Dimensions TES 1 Single Output Models Pin-Out Pin Single 3.0 Ø1.0 (Ø 0.04) vent hole (for reflow soldering process) 1 –Vin (GND) (0.12) 2 +Vin (Vcc) 8 5 4 –Vout 1 2 4 5 +Vout 8 *NC 3.04 2.54 5.08 (0.1) (0.12) (0.2) * Pin to be isolated from ( Magnification of A ) 13.7 (0.54) circuitry S SEATING PLANE 1.5 0.1 1.5 0.1 0.60 (0.02) (0.06 0.004) (0.06 0.004) 5.5 5.5 0.15 S (0.22) (0.22) Solder Pad Dimension 1.0 min. (0.04) Dimensions in [mm], () = Inch Pin pitch tolerances: ±0.10 (±0.004) Other tolerances: ±0.25 (±0.01) 2.54 5.08 (0.10) (0.10) http://www.tracopower.com Page 3 of 4 R0.5 0~4 3.0 (0.12) 6.7 (0.26) 8.0 (0.31) 0.3 (0.01) 7.0 0.5 11.0 0.2 11.6 (0.43 0.008) (0.28 0.02) (0.46) 1.6 (0.07) 0.25 [0.01] DC/DC Converters TES 1 Series 1 Watt Outline and Solder Pad Dimensions TES 1 Dual Output Models Pin-Out Pin Dual 1 –Vin (GND) 2 +Vin (Vcc) 3.0 Ø1.0 (Ø 0.04) vent hole (for reflow soldering process) (0.12) 4 Common 5 –Vout 10 7 7 +Vout 10 *NC 12 4 5 * Pin to be isolated from 3.04 2.54 5.08 2.54 circuitry (0.1) (0.12) (0.2) (0.1) 16.24 (0.64) ( Magnification of A ) S SEATING PLANE 1.5 0.1 1.5 0.1 0.60 (0.02) [0.06 0.004] [0.06 0.004] 5.5 5.5 0.15 S [0.22] [0.22] Solder Pad Dimension 1.0 min. (0.04) 2.54 5.08 2.54 (0.10) (0.10) (0.10) Dimensions in [mm], () = Inch Pin pitch tolerances: ±0.10 (±0.004) Other tolerances: ±0.25 (±0.01) Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com Rev. January 24. 2017 www.tracopower.com Page 4 of 4 R0.5 0~4 3.0 (0.12) 6.7 (0.26) 8.0 (0.31) 0.3 (0.01) 11.6 7.0 0.5 11.0 0.2 (0.46) (0.43 0.008) (0 .28 0.02) 1.6 (0.07) 0.25 [0.01]