OP130 Series Features:  TO-46 hermetically sealed package  Focused and non-focused optical light pattern “W”  Enhanced temperature range  Mechanically and spectrally matched to other OPTEK devices  Choice of power ranges  Choice of narrow or wide irradiance pattern Description: Each OP130 series device is a 935 nm gallium arsenide (GaAs) infrared LED mounted in a hermetically sealed TO-46 package that provides an enhanced temperature range with a variety of power ranges The TO-46 housing also offers high power dissipation and superior protection for hostile environments. Each OP130 device has a narrow beam with an inclusive angle at half power points of 18°. Each OP130W series device has a broad irradiance pattern of 50° at half power points, providing relatively even illumination over a large area. These devices are designed to efficiently operate with OP800, OP593, OP598 and OP599 phototransistors or the OP830 photodarlington. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Ordering Information Applications: Output Power Lead  Non-contact reflective object sensor Part LED Peak Lens Total Beam 2 (mW/cm ) Length  Assembly line automation Number Wavelength Type Angle Min / Max (Min)  Machine automation OP130 1.0 / NA  Machine safety OP131 3.0 / NA  End of travel sensor Dome 18° OP132 4.0 / NA OP133 935 nm 5.0 / NA 0.50" OP130W 1.0 / NA OP132W 4.0 / NA Flat 50° OP133W 5.0 / NA RoHS General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue C 08/2016 Page 1 © TT electronics plc OP130 Series Electrical Specifications OP130, OP131, OP132, OP133 Anode Cathode [MILLIMETERS] DIMENSIONS ARE IN: INCHES OP130W, OP132W, OP133W Anode Cathode [MILLIMETERS] Pin # LED DIMENSIONS ARE IN: INCHES 1 Anode 2 Cathode General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue C 08/2016 Page 2 © TT electronics plc OP130 Series Electrical Specifications Absolute Maximum Ratings (T = 25° C unless otherwise noted) A o o Storage Temperature Range -65 C to +150 C o o Operating Temperature Range -65 C to +125 C Reverse Voltage 2.0 V Continuous Forward Current 100 mA Peak Forward Current (2 us pulse width, 0.1% duty cycle) 10.0 A (1)(2) Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 260° C (3) Power Dissipation 200 mW Electrical Characteristics (T = 25° C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Radiant Power Output OP130, OP130W 1.0 - - P OP131 3.0 - - O (3 ) mW I = 100 mA F OP132, OP132W 4.0 - - OP133, OP133W 5.0 - - (3) V Forward Voltage - - 1.75 V I = 100 mA F F I Reverse Current - - 100 µA V = 2.0 V R R λ Wavelength at Peak Emission - 935 - nm I = 10 mA P F Spectral Bandwidth between Half Power β - 50 - nm I = 10 mA F Points Notes: 1. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. 2. Derate linearly 2.0 mW/° C above 25° C. 3. Measurement made with 100 µs pulse measured at the trailing edge of the pulse with a duty cycle of 0.1% and an I = 100 mA. F Electrical Characteristics (T = 25° C unless otherwise noted—for reference only) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS ∆λ /∆T Spectral Shift with Temperature - +0.30 - nm/°C I = Constant P F Emission Angle at Half Power Points I θ OP130 series - 18 - HP Degree = 100 mA F OP130W series - 50 - t Output Rise Time - 1000 - ns r I =100 mA, PW=10 µs, and F(PK) D.C.=10.0% t Output Fall Time - 500 - ns f General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue C 08/2016 Page 3 © TT electronics plc OP130 Series Performance OP130 Series (including “W” devices) Forward Voltage vs Forward Current vs Optical Power vs I vs Temp Temperature F 1.8 4.0 o Normalized at 20 mA and 20 C 1.7 3.5 -65°C -40°C 1.6 3.0 -20°C +0°C +20°C 1.5 +40°C 2.5 +60°C +80°C 1.4 +100°C 2.0 +125°C 1.3 1.5 -65°C 1.2 -40°C -20°C +0°C 1.0 1.1 +20°C +40°C +60°C 0.5 1.0 +80°C +100°C +125°C 0.9 0.0 0 5 10 15 20 25 30 35 40 45 0 5 10 15 20 25 30 35 40 45 50 Forward Current I (mA) Forward Current (mA) F Distance vs Output Power vs Forward Current 9 Normalized at 0.6" and 50 mA 8 Forward Current 7 10 mA 20 mA 30 mA 6 40 mA 50 mA 60 mA 5 80 mA 100 mA 4 3 2 1 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Distance (inches) General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue C 08/2016 Page 4 © TT electronics plc Typical Forward Voltage (V) Normalized Output Power Normalized Optical Power