OP599 Series Features:  Dark blue injection-molded plastic package  Variety of sensitivity ranges  T-1¾ package style with TO-18 base  Excellent optical lens surface  Excellent chip placement Description: Each device in this series consists of a NPN silicon phototransistor mounted in a dark blue plastic injection molded shell package, with a narrow receiving angle that provides excellent on-axis coupling and optical/mechanical axis alignment. The shell also provides excellent optical lens surface, control of chip placement and consistency of the outside package dimensions. The OP599 series sensors are 100% production tested for close correlation with OPTEK GaAIAs emitters. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data. Ordering Information Applications: Part Number Sensor Viewing Angle Lead Length  Applications requiring a narrow receiving angle OP599A  Applications that are space-limited OP599B Transistor 20° 0.75" OP599C OP599 2 1 [MILLIMETERS] DIMENSIONS ARE IN: INCHES CONTAINS POLYSULFONE To avoid stress cracking, we suggest using Pin # Sensor ND Industries’ Vibra-Tite for thread-locking. 1 Emitter Vibra-Tite evaporates fast without causing structural failure in OPTEK'S molded plastics. 2 Collector RoHS General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue A 08/2016 Page 1 © TT electronics plc OP599 Series Electrical Specifications Absolute Maximum Ratings (T = 25° C unless otherwise noted) A o o Storage and Operating Temperature Range -40 C to +100 C Collector-Emitter Voltage 30 V Emitter-Collector Voltage 5 V Continuous Collector Current 50 mA (1) Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 260° C (2) Power Dissipation 100 mW Electrical Characteristics (T = 25° C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS On-State Collector Current OP599A 2.35 - 3.85 mA I See Note (3). C(ON) OP599B 1.20 - 1.95 mA OP599C 0.40 - - mA I Collector-Dark Current - - 100 nA V = 10.0 V, E = 0 CEO CE E V Collector-Emitter Breakdown Voltage 30 - - V I = 100 µA (BR)CEO C V Emitter-Collector Breakdown Voltage 5.0 - - V I = 100 µA (BR)ECO E 2 (3 ) V Collector-Emitter Saturation Voltage - - 0.40 V I = 100 µA, E = 0.25 mW/cm CE(SAT) C E Notes: 1. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. A maximum 20 grams force may be applied to the leads when soldering. 2. Derate linearly 1.33 mW/° C above 25° C. 2 3. V = 5 V. Light source is an unfiltered GaAIAs emitting diode operating at peak emission wavelength of 890 nm and E of 0.25 mW/cm . CE E(APT) 4. This dimension is held to within ±0.005” on the flange edge and may vary up to ±0.020” in the area of the leads. General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue A 08/2016 Page 2 © TT electronics plc OP599 Series Performance General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue A 08/2016 Page 3 © TT electronics plc