OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Features:  Choice of four output options in low-cost side-looking package  Choice of two sensitivity options (OPL560/561/562/563)  High noise immunity  Direct TTL/LSTTL CMOS interface  Data rates to 250 kBaud for all except OPL560 series (200 kBaud)  Low power consumption RoHS Description: All components in this series include a photodiode, amplifier, voltage regulator, Schmitt trigger and NPN output transistor on a single silicon chip. OPL560 chips also include a voltage regulator on the chip. All devices in the series have a Photologic® chip that is encapsulated in a molded plastic side-looking package with an integral lens (recessed integral lens for OPL535 and OPL536). This packaging provides enhanced optical coupling, combined with mechanical protection. The hysteresis characteristics of the Schmitt trigger on each device offers high immunity to noise on input and V . CC OPL530, OPL531, OPL535 and OPL536 include a 10 K Ω pull-up resistor (R ) from output to V . These L CC components exhibit very stable performance over supply voltages ranging from 4.5 V to 16 V and a wide range of irradiance levels. OPL550 and OPL551 devices feature TTL/LSTTL compatible logic level output which can drive up to 8 TTL loads without additional circuitry and medium-speed data rates to 250 kBaud, with typical rise and fall times of 25 nanoseconds. OPL560, OPL561, OPL562 and OPL563 devices feature TTL/LSTTL compatible logic level output which can drive up to 10 TTL loads over supply voltages ranging from 4.5 V to 16 V. OPL530, OPL531, OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 are mechanically and spectrally matched to OP140 and OP240 LEDs. OPL535 and OPL536 are mechanically and spectrally matched to OP145 and OP245 series LEDs. Applications: Non-contact reflective object sensor, Assembly line automation, Machine automation, Machine safety, End of travel sensor, Door sensor Input Power Range 2 (mW/cm ) [Min/Max] Base Part Number Package Output Type - with Light - A B OPL530, OPL530-OC Internal 10K - High External Lens OPL531A, OPL531-OCA Internal 10K - Low 0.08/0.40 0.08/0.25 0.20/0.40 OPL535A, OPL535B Internal 10K - High Recessed Lens OPL536A, OPL536-OC, OPL536-OCA Internal 10K - Low OPL550, OPL550A, OPL550-OC, OPL550-OCA Totem Pole - High 0.25/2.4 0.25/1.4 N/A OPL551A, OPL551-OC, OPL551-OCA Totem Pole - Low 0.25/2.5 0.25/1.5 OPL560, OPL560A, OPL560-OCA Totem Pole - High External Lens 0.09/0.55 0.09/0.36 N/A OPL561, OPL561-OC, OPL561-OCA Totem Pole - Low OPL562, OPL562A, OPL562-OC, OPL562-OCA Totem Pole - High 0.025/0.23 0.025/0.14 N/A OPL563, OPL563-OC, OPL563-OCA Totem Pole - Low OC = Open Collector Output General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue D 04/2018 Page 1 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 OPL530, OPL550, OPL560 Series [ MILLIMETERS] DIMENSIONS ARE IN: INCHES Pin # Sensor 1 Ground Pin # Sensor 2 Output 1 Ground 3 V CC 2 Output 3 Vcc OPL535, OPL536 Series [ MILLIMETERS] DIMENSIONS ARE IN: INCHES Pin # Sensor Pin # Sensor 1 Ground 1 Ground 2 Output 3 V CC 2 Output 3 Vcc General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 2 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 (-OC, -OCA, -OCB) OPL550, OPL550A, OPL551A, OPL560, OPL560A, OPL561, OPL562, OPL562A, OPL563, OPL563A OPL550/550A/560/560A/562/562A Totem-Pole OPL530/535/550/560/562 (-OC, -OCA, -OCB) Open-Collector V CC V CC OUT OUT GND GND OPL 551A/561/563/563A Inverted Totem-Pole OPL 531/536/551/561/563 (-OC, -OCA, -OCB) Inverted Open-Collector V V CC CC OUT OUT GND GND General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 3 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 OPL530, OPL531A, OPL535A, OPL535B, OPL536, OPL536A OPL530, OPL535A/535B 10K Pull-Up OPL531A, OPL536/536A Inverted 10K Pull-Up V V CC CC OUT OUT GND GND V V CC CC OUT OUT GND GND General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 4 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Absolute Maximum Ratings (T = 25° C unless otherwise noted) A Input Diode Supply Voltage (V ) CC OPL530, OPL530-OC, OPL536-OC, 18 V OPL550 10 V OPL560, OPL561, OPL562, OPL563 18 V Operating Temperature Range -40° C to + 85° C Storage Temperature Range -40° C to + 100° C Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] 260°C Sourcing Current OPL560, OPL561, OPL562, OPL563 10 mA Power Dissipation OPL530, OPL530-OC, OPL536-OC 90 mW (2) OPL550, OPL560, OPL561, OPL562, OPL563 200 mW Sinking Current OPL530, OPL530-OC, OPL536-OC 50 mA OPL550 - OPL560, OPL561, OPL562, OPL563 50 mA (4) Voltage at Output Lead OPL530, OPL530-OC, OPL536-OC 35 V OPL550-OC, OPL551-OC 35 V OPL561-OC, OPL562-OC, OPL563-OC 35 V Duration of Output Short to V or Ground CC OP550 1 second Duration of Output Short to V CC OPL550-OC, OPL551-OC 1 second OPL560, OPL561, OPL562, OPL563, OPL561-OC, OPL562-OC, OPL563-OC 1 second Low Level Output Current OPL550, OPL551 Series 16 mA High Level Output Current OPL550, OPL551 Series 1 mA Irradiance 2 OPL550, OPL551 Series 10 mW/cm OPL560, OPL561, OPL561-OC 9 mW/cm 2 OPL562, OPL562-OC, OPL563, OPL563-OC 3 mW/cm Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. De- rate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For I on pull-up versions, add V /10 KΩ. CC CC General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 5 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (T = 25° C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Operating Supply Voltage OPL530, OPL530-OC, OPL531, OPL531-OC 4.5 - 16 - V OPL535, OPL535-OC, OPL536, OPL536-OC, OPL560, OPL561 Series V OPL550, OPL551 Series 4.5 - 5.5 - V Peak-to-Peak V Ripple Necessary to Cause False CC CC Triggering of Output OPL530, OPL530-OC, OPL531, OPL531-OC - - 2 V f = DC to 50 MHz OPL535, OPL535-OC, OPL536, OPL536-OC OPL560, OPL561 Series OPL550, OPL551 Series - 2 - V V = 5 V DC, f = DC to 50 MHz CC (4) Supply Current 2 OPL530, OPL530-OC - 2.7 5 mA E = 0 or 1 mW/cm E OPL536-OC I CC 2 OPL550, OPL551 Series - 8 15 mA E = 0 or 3 mW/cm , V = 5.5 V E CC 2 OPL560, OPL561 Series - 8 12 mA E = 0 or 1 mW/cm E (3) Positive-Going Threshold Irradiance 2 OPL530, OPL530-OC 0.08 - 0.40 mW/cm T = 25° C A OPL536-OC 2 OPL531A, OPL531-OCA 0.08 - 0.25 mW/cm T = 25° C A OPL535A, OPL536A, OPL536-OCA E eT(+) 2 OPL535B 0.12 - 0.40 mW/cm T = 25° C A 2 OPL550, OPL550-OC, OPL551-OC .25 - 2.4 mW/cm V = 5 V, T = 25° C CC A 2 OPL550A, OPL550-OCA, OPL551-OCA .25 - 1.4 mW/cm V = 5 V, T = 25° C CC A General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 6 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (T = 25° C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Hysteresis Ratio OP530, OP531 Series 1.05 1.3 1.6 - - OP535, OP536 Series 1.05 1.2 1.5 - - E E eT(+)/ eT(-) OPL550, OPL551 Series 1.05 2 2.5 - - OPL560, OPL561 Series 1.20 1.55 2 - - Temperature Co-efficient OPL530, OPL530-OC - -0.6 - %/°C >0°C ∆E (+)(∆T) et OPL536-OC - -1.6 - %/°C <0°C Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For I on pull-up versions, add V /10 KΩ. CC CC General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 7 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (T = 25° C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Operating Supply Voltage OPL550 2.4 3.3 - V V = 4.5 V, I = -800 µa, CC OH 2 E = 3 mW/cm E V OH 2 OPL560 V -2.1 - - V I = -1 µA, E = 1 mW/cm CC OH E OPL561 V -2.1 - - V I = -1 µA, E = 0 CC OH E Low Level Output Voltage OPL530, OPL530-OC - 0.2 0.4 V I = 16 mA, E = 0 OL E 2 OPL536-OC - 0.2 0.4 V I = 16 mA, E = 1 mW/cm OL E OPL550 - 0.25 0.4 V V = 4.5 V, I = 12.8 mA, CC OL V OL E = 0 E OPL560 - - .4 V I = 16 mA, E = 0 OL E 2 OPL561, OPL561-OC - - .4 V I = 16 mA, E = 1 mW/cm OL E Short Circuit Output Current OPL550 -20 -55 -100 mA V = 5.5 V, Output = GND, CC 2 I E = 3 mW/cm OS E (4) High Level Output Current OPL536-OC - 0.1 10 µA V = 30 V, E = 0 OH E 2 OPL530, OPL530-OC - 0.1 10 µA V = 30 V, E = 1 mW/cm OH E OPL550-OC - 1 100 µA V = 4.5 V, V = 30 V, CC OH I OH 2 E = 3 mW/cm E OPL551-OC - 1 100 µA V = 4.5 V, V = 30 V, CC OH E = 0 E OPL561-OC - - 100 µA V = 30 V, E = 0 OH E Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For I on pull-up versions, add V /10 KΩ. CC CC General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 8 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (T = 25° C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Output Rise Time 2 OPL530 - 1.5 - µs E = 0 or 1 mW/cm , C = 50 pF E L 2 OPL530-OC, - 50 - ns E = 0 or 1 mW/cm , RL = 300 Ω to 5 V, E OPL536-OC C = 50 Pf L 2 - 25 70 ns V = 5 V, T = 25° C, E = 0 or 3 mW/cm , CC A E OPL550 f = 10 kHz, DC = 50% t r RL = 8 TTL loads 2 - 25 70 ns V = 5 V, T = 25° C, E = 0 or 3 mW/cm , CC A E OPL550-OC, OPL551-OC f = 10 kHz, DC = 50%, R = 360 Ω L 2 OPL560, OPL561 - - 70 ns T = 25° C, E = 0 or 1 mW/cm , A E f = 10 kHz, DC = 50%, OPL561-OC - - 100 µs R = 360 Ω L Output Rise Time 2 OPL530 - - - µs E = 0 or 1 mW/cm , C = 50 pF E L 2 OPL530-OC, - - - ns E = 0 or 1 mW/cm , RL = 300 Ω to 5 V, E OPL536-OC C = 50 pF L 2 OPL550-OC, OPL551-OC - 25 70 ns V = 5 V, T = 25° C, E = 0 or 3 mW/cm , CC A E R = 8 TTL loads, L t r f = 10 kHz, DC = 50% 2 OPL561-OC - - 70 ns V = 5 V, T = 25° C, E = 0 or 3 mW/cm , CC A E R = 8 TTL loads, L f = 10 kHz, DC = 50% 2 OPL560, OPL561 - - 70 ns T = 25° C, E = 0 or 1 mW/cm , A E f = 10 kHz 2 OPL561-OC - - 100 ns T = 25° C, E = 0 or 1 mW/cm , A E f = 10 kHz Output Fall Time 2 OPL530 - 20 - ns E = 0 or 1 mW/cm , C = 50 Pf E L 2 OPL530-OC, - 20 - ns E = 0 or 1 mW/cm , RL = 300 Ω to 5 V, E OPL536-OC C = 50 pF L 2 t f OPL550-OC, OPL551-OC - 25 70 ns V = 5 V, T = 25° C, E = 0 or 3 mW/cm , CC A E R = 360 Ω, f = 10 kHz, DC = 50% L 2 T = 25° C, E = 0 or 1 mW/cm , A E OPL560, OPL561 - - 70 ns f = 10 kHz 2 T = 25° C, E = 0 or 1 mW/cm , A E OPL561-OC - - 100 ns f = 10 kHz Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For I on pull-up versions, add V /10 KΩ. CC CC General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 9 © TT electronics plc OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (T = 25° C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Propagation Delay 2 OPL530 - 1.0 - µs E = 0 or 1 mW/cm , RL = 300 Ω to 5 V, E C = 50 pF L 2 OPL530-OC, - 1.0 - µs E = 0 or 1 mW/cm , RL = 300 Ω to 5 V, E tpE (+) eT OPL536-OC C = 50 pF L - 2.5 5 µs V = 5 V, T = 25° C, CC A 2 OPL550-OC, OPL551-OC E = 0 or 3 mW/cm , R = 8 TTL loads, f = E L 10 kHz, DC = 50% Propagation Delay 2 OPL530, - 3.0 - µs E = 0 or 1 mW/cm , RL = 300 Ω to 5V, C E L OPL530-OC, = 50 pF tpE (-) OPL536-OC eT 2 OPL550-OC, OPL551-OC - 2.5 5 µs V = 5 V, T = 25° C, E = 0 or 3 mW/cm , CC A E R = 360 Ω, f = 10 kHz, DC = 50% L Propagation Delay (Low-High/High-Low) OPL560, OPL561 - 5 - µs DC = 50%, R = 10 TTL Loads L t , T PLH PHL OPL561-OC - 5 - µs DC = 50%, R = 300 Ω L Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL536, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. De- rate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For I on pull-up versions, add V /10 KΩ. CC CC General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue CD 04/2018 Page 10 © TT electronics plc