ADVANCED ENERGY 0.6V24-P1

ULTRAVOLT® V SERIES VERTICAL, MICRO-SIZED HIGH VOLTAGE BIASING SUPPLIES Single-output micro-sized HV modules The vertical, micro-sized V series is the ideal solution for applications that require a bias voltage ranging from 0 3 to 3000 V and very small current, at only 13.8 cc (0.84 in ). 2 2 With a footprint under 2.54 cm (1 in ), these modules are perfect for applications with limited board space. Functions Typical Applications › 7 models from 0 to 600, › Bias supplies 1000, 1250, 1500, 2000, › Electrostatic chucks 2500, or 3000 V › Hand held X-Ray Florescence › 0.5, 0.8, or 1 W of output (XRF) power › Avalanche photo diodes (APD) › Tight line/load regulation › Photomultiplier Tubes (PMT) › Arc and continuous short › Silicon Detector (SiD) circuit protection › X-Ray Flat Panel detector › Self-restoring output voltage (FPD) › Low cost › Ionization Chamber detector › Miniature and lightweight › Voltage monitoring › Low ripple (0.01% peak to peak) › Optional flying lead for high voltage output PARAMETER SPECIFICATIONS UNITS 5 ±0.5 (2 to 3 kV ONLY) 12 ±1, 15 ±1 (600 V to 1.5 kV ONLY), or 24 ±2 VDC Input Voltage Vin (Pins 1 and 2) 5 (2 to 3 kV ONLY) 12 15 (600 V to 1.5 kV ONLY) 24 V Input Voltage No load: 55, full load: 450 No load: 45, full load: 200 No load: 40, full load: 190 No load: 35, full load: 160 mA Input Current Fixed positive and fixed negative - Polarity 0 to 600 0 to 1000 0 to 1250 0 to 1500 VDC Output Voltage 12 15 24 12 15 24 12 15 24 12 15 24 VDC Input Voltage 0.5 0.8 1 0.5 0.8 1 0.5 0.8 1 0.5 0.8 1 W Output Power 0.83 1.33 1.67 0.5 0.8 1 0.4 0.64 0.8 0.33 0.53 0.67 mA Output Current VDC Output Voltage 0 to 2000 0 to 2500 0 to 3000 VDC Input Voltage 5 12 24 5 12 24 5 12 24 W 0.5 0.8 1 0.5 0.8 1 0.5 0.8 1 Output Power 0.25 0.40 0.50 0.20 0.32 0.40 0.167 0.267 0.333 mA Output Current 10 to 100K (potentiometer across Vref. and signal ground, wiper to adjust) - HV Setting < 0.01% of full output voltage for no load to full load VDC Load Voltage Regulation < 0.01% of full output voltage over specified input voltage range VDC Line Voltage Regulation < 0.01% at full load V pk to pk Residual Ripple 100 ppm/°C for the max output voltage after starting and over temperature range 0 to 50°C - Temperature Coefficient +1 V/1 kV max or -1 V/-1 kV max according to model polarity output impedance = 200 kΩ ±1% - Output Voltage Monitor (600 to 1500 V) 12 to 24 V input only: 0 to +5 V ±2% Output Voltage Monitor (2 to 3 kV) 5 V inputs: 0 to +2.5 V ±2% VDC 12 to 24 V input only: 5 V ±1%, TC: 100 ppm/°C, max output current: 1 mA Reference Voltage 5 V inputs: 2.5 V ±1%, TC: 100 ppm/°C, max output current: 1 mA - -10 to +65, full load, max Eout, case temp. °C Operating Temperature -20 to +70 °C Storage Temperature Arc and short circuit protection - Safeguards Flying lead for HV output Options Enable/disable (ON/OFF): 0 V to +0.5 V enable, +2.4 V to V_input disable (default = disable) - Enhanced Interface (-EI) Option (2 to 3 kV Only) Output current monitor (5 V input only): 0 to +2.5 V ±2% Output current monitor (12 to 24 V input): 0 to +5.0 V ±2% - FLYING LEAD OPTION-WS Note: Pins 7 and 8 are available for 2 k to 3 kV units with enhanced interface option ONLY. Drawing views: third angle projections. PHYSICAL SPECIFICATIONS Steel, tin-plated, thickness 0.5 mm (0.02") Construction Insulation: fully potted in an epoxy resin 3 13.8 cc (0.84 in ) Volume 35 g (1.23 oz) Weight Tolerance ±0.76 mm (0.0030") Overall ±0.38 mm (0.015") Pin to Pin ±0.51 mm (0.020") Tabs Location ±0.25 mm (0.010") Tab to Tab Notes: 0.47 mm (0.019") round pins, length: 3 mm (0.12"), spacing: 2.54 mm (0.1") PCB mounting through 4 mounting tabs: length: 5 mm (0.2"), width: 1.5 mm (0.059"), thickness: 0.5 mm (0.02") Optional flying lead for HV output: coaxial cable (RG178), diameter: 2 mm (0.079"), length: 500 mm (19.685") CONNECTIONS Pin Function POSITIVE POWER INPUT 1 POWER GROUND 2 SIGNAL GROUND 3 REMOTE ADJUST INPUT 4 REFERENCE VOLTAGE 5 VOLTAGE MONITOR 6 CURRENT MONITOR (available with -EI option ONLY) 7 ENABLE (available with -EI option ONLY) 8 HV OUTPUT 9 Note: Mounting tabs must be connected to ground. ORDERING INFORMATION 0 to 600 VDC Output 0.6 V Type 0 to 1000 VDC Output 1 V 0 to 1250 VDC Output 1.25 V 0 to 1500 VDC Output 1.5 V 0 to 2000 VDC Output 2 V 0 to 2500 VDC Output 2.5 V 0 to 3000 VDC Output 3 V 5 VDC Nominal (2 to 3 kV Only) 5 Input 12 VDC Nominal 12 15 VDC Nominal (600 V to 1.5 kV Only) 15 24 VDC Nominal 24 0.5 W Output 0.5 Power 0.8 W Output 0.8 1 W Output 1 Tin Steel Case (Standard) Case Positive Output -P Polarity Negative Output -N Shielded Flying Lead for HV Output (600 V to 1.5 kV Only) -WS Option Flying Lead for HV Output (2 to 3 kV Only) -W Current Monitor/Enable Pin (2 to 3 kV Only) -EI Example: 1.5V24-P1-WS Voltage Option IEC-60950-1 Type Model Power Non-RoHS compliant units are available. Please contact the factory for more information. Input Polarity Popular accessories ordered with this product include The V series is not available in all territories. Please contact Advthe PCB-C anced Energy f ONN-M/V or details c . oncerning sales in your area. For international contact information, visit advanced-energy.com. ENG-HV-Vseries-230-G 4.16 Specifications are subject to change without notice. ©2016 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy® AE®, and UltraVolt® are U.S. trademarks of Advanced Energy Industries, Inc.