ADVANCED ENERGY 40C24-N125

ULTRAVOLT® HIGH-POWER 40C TO 60C SERIES 40 TO 60 KV HIGH VOLTAGE CAP-CHARGING SUPPLIES Single-output DC to high voltage DC modules for capacitor charging and DC power The high-power 40C to 60C line of high voltage regulated DC-to-DC converters is an extension of the C series, directly addressing the high-power-density needs of > 30 W applications from 40 to 60 kV. This high power density is especially suited to high-energy systems with large capacitances, fast repetition rates, or high continuous-DC-power requirements. Features Typical Applications › 3 models from 0 to 40 kV › Pulsed laser through 0 to 60 kV › Ion pump › 60, 125, or 250 W output › Plasma generator power › Electrostatic precipitator › Maximum Iout capability down › Deposition to 0 V › HV amplifier bias › Maximum Iout during charge/rise time › HV cap charger › Output short-circuit protection › HV pulse generator › Very fast rise with very low › HV test equipment over-shoot · Insulation testing (hi-pot) › High eciency · Time-domain-resolver (TDR) › High power density · Motor winding tester or cable › Output current and voltage thumper monitors › > 200,000 hour MTBF at 65°C › Fixed-frequency, low-stored-energy design › Optional digital-ready higher-performance interface (-I5/-I10) PARAMETER CONDITIONS UNITS Input All Types Full Power +23 to 30 VDC Voltage Range Voltage Range Derated Power Range 15 to 23; 30 to 32 VDC Current Standby/Disable < 150 mA No Load, Max Eout < 1250 mA Current Max Load, Max Eout < 13 A Current Output 40 C 50 C 60 C Nominal Input 0 to 40,000 0 to 50,000 0 to 60,000 VDC Voltage Range Nominal Input, Max Eout 60 125 250 60 125 250 60 125 250 Watts Power Iout, Entire Output Voltage Range 1.50 3.13 6.25 1.20 2.50 5.00 1.00 2.08 4.17 mA Current Full Load 0.30 0.63 1.25 0.24 0.50 1.00 0.20 0.42 0.83 mA/V Current Scale Factor 10,000:1 ±2% - Voltage Monitor Scaling Capacitance/95% Decay (50 Meg Load) 750/104 750/104 375/52 600/84 600/84 300/42 500/70 500/70 250/35 pF/mS Internal Capacitance Full Load, Max Eout < 1% V p-p Ripple Max Iout, Various C Loads and Eout Figure A - Rise Time Internal 750 750 375 600 600 300 500 500 250 pF Storage Capacitance Over-shoot C Load, 0 Eout to Full Eout < 1% V pk Line Regulation Nom. Input, Max Eout, Full Power < 0.01% VDC Static Load Regulation No Load to Full Load, Max Eout < 0.01% VDC Stability 30 Min Warmup, Per 8 H Per Day < 0.01%/< 0.02% VDC Programming and Controls All Types Nominal Input +Output models 1.1 MΩ to GND, -output models 1.1 MΩ to +5 Vref MΩ Input Impedance Typical Potentiometer Values 10 to 100 K (Pot. across Vref. and signal GND, wiper to adjust) Ω Adjust Resistance 0 to +5 for +Out, +5 to 0 for -Out +4.64 VDC for +output or +0.36 for -output = nominal Eout - Adjust Logic Output Voltage and Impedance T=+25°C +5.00 VDC ±1%, Zout = 464 Ω ±1% - 0 to +0.8 V disable, +2.0 to 30 enable (default = enable) VDC Enable/Disable Environmental All Types Full Load, Max Eout, Case Temperature -40 to +65 °C Operating Over the Specified Temperature PPM/°C Coefficient ±50 (±25 optional) Thermal Shock Mil-Std-810, Method 503-4, Proc. II -40 to +65 °C Storage Non-Operating, Case Temp. -55 to +105 °C All Conditions, Standard Package 0 to 95% non-condensing - Humidity Standard Package, All Conditions Sea level through 70,000 ft Altitude Shock Mil-Std-810, Method 516.5, Proc. IV 20 Gs Vibration Mil-Std-810, Method 514.5, Fig. 514.5C-3 10 Gs Figure A. Rise time formulas C = uF C = uF C = uF C = uF 2 C x V I C x E V = Volts V = kV V = kV T = I = C x V x F F = E² = kV J = I = mA I = mA I = mA I CxV 2 J = Ws T = mS F = Hz F = Hz Note: Capacitance must include HVPS internal capacitance. 40C AND 50C 13.160 [334.3 mm] 9.160 [232.7 mm] 6.710 [170.4 mm] 5.300 [134.6 mm] 5.050 [128.3 mm] 2.420 [61.5 mm] 2.320 [58.9 mm] (3.09 [78.6 mm]) .375 [9.5 mm] 1.160 [29.5 mm] 2.500 [63.5 mm] .330 [8.4 mm] .050 [1.3 mm] 7 14 6 13 1.960 [49.8 mm] 5 12 4.490 [114.0 mm] (1.200 [30.5 mm]) 4 11 3.940 [100.1 mm] 3 10 2 9 1 8 .739 [18.8 mm] 1.970 [50.0 mm] 16 15 .380 [9.7 mm] .990 [25.1 mm] 1.640 [41.7 mm] .040 [1.0 mm] .19 [4.7 mm] 14.000 [355.6 mm] .525 [13.3 mm] ALTERNATE MOUNTING 2.2 INSTALL 8-32 THREADED 12.750 [323.9 mm] SET SCREWS IN "A "HOLES 7.250 [184.2 mm] .750 [19.1 mm] 2.500 [63.5 mm] .375 [9.5 mm] A A A A .375 [9.5 mm] 3.375 [85.7 mm] 3.000 [76.2 mm] A A A A 40C AND 50C WITH -WS AND 60C .44 [11.1 mm] 6-32 UNC - 2A .753 [19.1 mm] 1.600 [40.6 mm] 28.00 [711.2 mm] .885 [22.5 mm] PHYSICAL SPECIFICATIONS 2 2 Gold-plated 0.64 mm (0.025 in ) Pins Center of pins and mounting holes located from center of pin 1 Pins 1 through 14 spacing: 2.54 mm x 5.08 mm (0.100" x 0.200") on center, height from cover 7.11 mm (0.280") min Pins 15 and 16 spacing: 2.54 mm (0.100") on center, height from cover 11.43 mm (0.450") min 40C-50C LGH flying lead cable assembly required, P/N CA-50KV-1000 HV Output Connection 60C standard 0.7 m (28") coaxial flying lead RTV-filled aluminum box Construction Chem film per MIL-A-8625 Type II (anodizing) 3 3 0.0026 m (160 in ) Approx. Volume 4.5 kg (10 lb) Approx. Weight ±1.02 mm (0.040") pin to pin 0.38 mm (0.015") Overall 0.76 mm (0.03") Hole-to-Hole Location CONNECTIONS ORDERING INFORMATION 40,000 VDC Output 40C Pin Function Type 50,000 VDC Output 50C Input-power ground 21 and 22 return 60,000 VDC Output 60C Positive power input 19 and 20 24 VDC Nominal 24 Input Iout monitor 3 Positive Output -P Polarity Enable/disable 4 Negative Output -N Signal ground return 5 60 W Output 60 Power Remote adjust input 125 W Output 125 6 +5 VDC reference 250 W Output 250 7 output 1.02 cm (0.400") High (Sized to -H Heat Sink N/C (or arc detect Fit Case) 10 option) (5) 0.47 cm (0.187") Standoffs -Z11 PCB Support N/C on Top Cover 11, 12, and 13 5 V Controls and Monitors -I5 Eout monitor Enhanced Interface 14 10 V Control and Monitors -I10 HV ground return 15 and 16 Arc Detect* -AD Options • All grounds joined internally. Power-supply Arc Quench* -AQ mounting points isolated from internal * Available only with I5 or I10 options grounds by > 100 kΩ, 0.01 µF/500 V (max). Note: For more information on the enhanced interface options, download the I5/I10 option datasheet. Example: 40C24-P125-I5 Voltage Option Type Model Power Input Polarity IEC-60950-1 Non-RoHS compliant units are available. Please contact the factory for more information. Manufactured in U.S.A. For international contact information, visit advanced-energy.com. ENG-HV-HP40C60C-230-A 4.16 Specifications are subject to change without notice. ©2016 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy® and UltraVolt® are U.S. trademarks of Advanced Energy Industries, Inc.