ADVANCED ENERGY MPM12-2KN

HITEK POWER® MPM SERIES MINIATURE HIGH VOLTAGE DC-TO-DC CONVERTERS MPM SERIES The MPM series offers a unique range of low cost, general purpose high voltage DC-to-DC converters. All units are configured for direct PCB mounting and are intended to be “designed in” to equipment as a component. DESCRIPTION The MPM series is suitable for ink jet printing, electrostatic precipitation, Geiger-Muller tubes, photomultiplier tubes, electron beam deflection and focusing, as well as various general purpose applications. These units’ unregulated output is proportional to the input voltage. Alternatively, customers can add their own external feedback control loops to provide regulated outputs. The converters are vacuum encapsulated in an ABS case to ensure maximum reliability and safety. Standard MPM models are three-pin devices that provide a common 0 V for input and output. All models are available with a range of input and output voltages, with either positive or negative output. MPM series units are fully encapsulated in silicone rubber to give reliable and consistent operation over wide environmental conditions. All units are fully ATE tested to ensure consistent performance. FEATURES › Output power: 1.5 W, continuous › Output voltage: 100 V to 3 kV › Output isolation option › Ripple: 0.05% peak to peak (screened versions) › Temperature coefficient: < 300 ppm/°C › Stability: < 0.1% per hour after stabilization, over eight hour period › PCB Mounting › Small size › Positive or negative polarity › Output proportional to input › No minimum load requirements › Input polarity protected › Open- and short-circuit protected › EU RoHS compliant to 2011/65/EU, CE marked (LVD) Page 2 SPECIFICATIONS Output Power 1.5 W, max, continuous Output Voltage Units available with max output voltages from 100 V to 3 kV (see table for specific versions). 12 V units: 1.2 to 12 V for 10 to 100% output voltage Input Voltage 24 V units: 2.4 to 24 V for 10 to 100% output voltage 12 V units: typically 40 mA offload, 200 mA fully loaded Input Current 24 V units: typically 25 mA offload, 110 mA fully loaded Polarity Positive or negative to order Load Regulation Typically < 10% (for a 0 to 1.5 W load change), max 20% Line Regulation Output is proportional to input over a 10 to 100% input range. Stability < 0.1% after stabilization and over an eight hour period Ripple 0.5% peak to peak (0.05% for screened case version) MTBF > 500,000 hours MTBF as per IEC62380:2004 Efficiency > 50% at 1.5 W load Oscillator Frequency 30 to 200 kHz, depending on model Protection Protected against intermittent short circuit and flashover Operating Temperature -10 to +60°C (14 to 140°F) Storage Temperature -40 to +85°C (-40 to 185°F) Humidity 80% max relative humidity up to 31°C (88°F), reducing linearly to 50% at 40°C (104°F); non-condensing Altitude Sea level to 2000 m (6500′) Temperature Coefficient < 300 ppm/°C Screened Case (Optional) Screened case of tin plate construction with its own pin reduces radiated noise and output ripple. Isolated units give input to output isolation of up to 100 V. This can allow, for example, a sense resistor to be Isolated Unit (Optional) added for load current measurements. A capacitor may be added between the input 0 V and output 0 V to reduce common mode ripple. Meets the requirements of the Low Voltage Directive (LVD) 2006/95/EC, by complying with BS EN60950 Safety when it is installed as a component part of other equipment and is CE marked accordingly Meets the requirements of EU Directive 2011/65/EU on the Restriction of use of certain Hazardous RoHS Substances in Electrical and Electronic Equipment (RoHS) Mechanical Specification Dimensions See outline drawing, on page 5. Weight 60 g (2 oz), approx. Page 3 Upta quam: nonsectem aut vella et facerovit, undipsunt pel ipsa quidenimusam labore nit quas eici conet modite quae porio dis preritenihil et plique di aligendi omnia sunt maionse quature rumquaera aliqui odit. OUTPUT AND ORDERING INFORMATION Model Input Voltage Output Voltage Output Current MPM12-100* 12 V 100 V 15 mA MPM24-100* 24 V 100 V 15 mA MPM12-200* 12 V 200 V 7.5 mA MPM24-200* 24 V 200 V 7.5 mA MPM12-300* 12 V 300 V 5 mA MPM24-300* 24 V 300 V 5 mA MPM12-500* 12 V 500 V 3 mA MPM24-500* 24 V 500 V 3 mA MPM12-1K* 12 V 1 kV 1.5 mA MPM24-1K* 24 V 1 kV 1.5 mA MPM12-1K5* 12 V 1.5 kV 1 mA MPM24-1K5* 24 V 1.5 kV 1 mA MPM12-2K* 12 V 2 kV 0.75 mA MPM24-2K* 24 V 2 kV 0.75 mA MPM12-3K* 12 V 3 kV 0.5 mA MPM24-3K* 24 V 3 kV 0.5 mA *Please add the required suffix to the model number: P or N: Positive or negative polarity S: Screened version I: Isolated unit e.g. MPM12-300PS for a 12 V input voltage, 300 V output voltage, positive, screened unit 12 V MPM 24 V MPM 12 V MPM 24 V MPM 100% 100% 90% 90% 80% 80% 70% 70% 60% 60% 50% 50% 40% 40% 30% 30% 20% 20% 10% 10% 0% 0% 1.2 2.4 3.6 4.8 6 7.2 8.4 9.6 10.8 12 2.4 4.8 7.2 9.6 12 14.4 16.8 19.2 21.6 24 12 V MPM 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 24 V MPM 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Input Voltage Input Voltage These component power supplies meet the requirements of EC Directive 2006/95/EC (LVD). Page 4 Output Voltage Output Voltage Drawing dimensions are in mm (inches). Design developments may result in specification changes. UNSCREENED VERSION RECOMMENDED PCB FOOTPRINT 38.1 (1.50) 20.1 (0.79) HOLE 1.6 THRU 4 POSITIONS I/P O/P I/P 0V 0V O/P 17.2 8.7 (0.34) 17.2 (0.68) (0.68) 6.1 (0.24) 27.9 (1.10) ISOLATED VERSION ONLY 27.9 (1.10) RECOMMENDED PCB FOOTPRINT SCREENED VERSION SCREEN CAN PIN HOLE 1.6 THRU 0.7x0.5 (0.028x0.020) 39.3 (1.55) 5 POSITIONS 21.7 6.4 (0.25) 6.4 (0.25) 8.0 (0.31) (0.85) I/P O/P I/P 0V 0V O/P 17.2 8.1 (0.32) 17.2 (0.68) (0.68) 6.7 (0.30) 27.9 (1.10) ISOLATED VERSION ONLY 27.9 (1.10) Page 5 Upta quam: nonsectem aut vella et facerovit, undipsunt pel ipsa quidenimusam labore nit quas eici conet modite quae porio dis preritenihil et plique di aligendi omnia sunt maionse quature rumquaera aliqui odit. 3.2 (0.13) 2.6 (0.10) 35.2 (1.39) 30.5 (1.20) 30.5 (1.20) 1.3 (0.51) 1.3 (0.051) Ø1.02 (0.04) Ø1.02 (0.04) 38.1 (1.50) 39.3 (1.55) 1.3 (0.51) 1.3 (0.51) 30.5 (1.20) 30.5 (1.20) 35.2 (1.39) Advanced Energy Industries, Inc. HiTek Power Ltd.® Hawthorn Road Littlehampton West Sussex BN17 7LT United Kingdom +44 0 1903 712400 sales.support-HTP@aei.com advanced-energy.com ENG-HV-MPM-230-01 11.15 ® ® Specifications are subject to change without notice. ©2015 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy , AE , HiTek Power®, and HiTek Power Ltd.® are U.S. trademarks of Advanced Energy Industries, Inc.