ADVANCED ENERGY MSP-103P

HITEK POWER® MSP SERIES MASS SPECTROMETRY POWER SUPPLY MODULES The MSP series consists of high stability, unipolar source modules that perform reliably even under short-circuit or arc conditions. They are available either as positive or negative output voltage modules, and can be set by internal potentiometer, external voltage, or external potentiometer. MODULAR DESIGNS, CUSTOM SOLUTIONS The modular design of AE high voltage products for mass spectrometry enables an array of performance features and combinations. From simple options, such as cable length and connector type, to complete custom designs, we deliver solutions that precisely fulfill your specific requirements. FEATURES › Output power: 0 to 10 W › Output voltage: 10 V to 20 kV › Ripple: < 10 to < 200 mV › Temperature coefficient: 10 or 25 ppm/°C › Stability: 0.002% (20 ppm) in 15 minutes, < 0.01% (100 ppm) in eight hours after warmup › Screened case for low magnetic radiation › High reliability › Versatile control options PROVEN POWER-CONVERSION TOPOLOGIES, CONTROL METHODS, AND MECHANICAL EXPERTISE Page 2 SPECIFICATIONS Output Power 10 W, max, depending on model Output Voltage 10 V to 20 kV, depending on model Output Current 0.4 to 10 mA, depending on model Input Voltage +24 VDC ±10% Input Current 1 A, max, depending on model Line Regulation < 10 ppm for a 1 V input voltage change Load Regulation < 10 ppm for 10 to 100% load change Ripple < 10 to < 200 mV, depending on model 0 to +10 V = 0 to 100 %, accuracy ±2% Voltage Control Can also be controlled by internal or external potentiometer (See connection details below.) Current Control Fixed at approximately 110 to 130% of max Voltage Monitor 0 to +10 V = 0 to 100%, accuracy ±2% Current Monitor 0 to +10 V = 0 to 100%, accuracy ±2% Stability < 0.002% (20 ppm) in 15 minutes, < 0.01% (100 ppm) in eight hours (after one hour warmup) Temperature Coefficient 10 or 25 ppm/°C at max output voltage (tested with external voltage control) Cooling Convection cooled Protection The units are fully protected against short circuit and intermittent arcs to ground Operational Temperature 10 to 50°C (50 to 122°F) Storage/Transport Temperature -20 to 85°C (-4 to 185°F) Operational Altitude Sea level to 2000 m (6500′) Storage/Transport Altitude Sea level to 18000 m (59,055′) Reliability MTBF > 50,000 hours 80% max relative humidity up to 31°C (88°F), reducing linearly to 50% at 40°C (104°F); non-condensing (ref Humidity EN61010-1) Meets the requirements of the Low Voltage Directive, 2006/95/EC by complying with BS EN61010-1:2010 Safety when installed as a component part of compliant equipment. Units are CE marked accordingly. Meets the requirements of EU Directive 2011/65/EC on the Restriction of use of certain Hazardous RoHS Substances in Electrical and Electronic Equipment (RoHS). Construction A fabricated aluminum alloy case is used for good heat dissipation and screening. Mechanical Specifications Dimensions See Output and Ordering Information table, on page 4. Weight See Output and Ordering Information table, on page 4. Casing Aluminum, clear non-chrome passivate finish Output Cable Unterminated URM76; 1 m (3.3′) of screened output cable Connectors Various options are available upon request. Page 3 Upta quam: nonsectem aut vella et facerovit, undipsunt pel ipsa quidenimusam labore nit quas eici conet modite quae porio dis preritenihil et plique di aligendi omnia sunt maionse quature rumquaera aliqui odit. OUTPUT AND ORDERING INFORMATION Model Output Voltage Output Current Ripple (pk to pk) Size Weight 147 mm x 98 mm x 47 mm MSP-102* 10 V to 1 kV 10 mA < 10 mV 0.8 kg (1.8 lb) (5.8″ x 3.9″ x 1.9″) 147 mm x 98 mm x 47 mm MSP-252* 10 V to 2.5 kV 4 mA < 15 mV 0.8 kg (1.8 lb) (5.8″ x 3.9″ x 1.9″) 147 mm x 98 mm x 47 mm MSP-502* 25 V to 5 kV 2 mA < 20 mV 0.8 kg (1.8 lb) (5.8″ x 3.9″ x 1.9″) 200 mm x 98 mm x 47 mm MSP-103* 50 V to 10 kV 1 mA < 50 mV 1 kg (2.2 lb) (7.9″ x 3.9″ x 1.9″) 200 mm x 98 mm x 47 mm MSP-153* 75 V to 15 kV 0.66 mA < 100 mV 1 kg (2.2 lb) (7.9″ x 3.9″ x 1.9″) 210 mm x 120 mm x 46 mm MSP-203* 100 V to 20 kV 0.4 mA < 200 mV 1 kg (2.2 lb) (8.3″ x 3.9″ x 1.9″) * Please add the required suffix to the model number: P: Positive polarity N: Negative polarity e.g. MSP-502P for a positive unit INTERFACE CONNECTIONS NOT CONNECTED 1 Molex KK Series 3003 0.2” 10-Way Connector, 2 +24 VDC INPUT SUPPLY Mating Half Shell 10-01-1104 and Crimps 08-50-0108. 3 VOLTAGE MONITOR CONTROL LINK (+10 V REF) 4 CONTROL LINK 5 6 CONTROL LINK VOLTAGE CONTROL 7 CURRENT MONITOR 8 9 SIGNAL GROUND 0 V INPUT 10 CONTROL LINK DIAGRAM If the current monitor option is fitted, an external resistor of less than 50K with a clamp device or link must be fitted between pins 8 and 9. Page 4 Drawing dimensions are in mm (inches). MSP-102 Design developments may result in specification changes. MSP-252 MSP-502 147.0 (5.79) 15.0 (0.59) MOUNTING: 2 OFF M4 STUDS; LENGTH AND POSITION AS SHOWN DIMENSIONS mm (in) 1000 13.5 (0.53) 54.0 (2.13) 81.0 (3.19) 15.0 (0.59) 47.0 (1.85) Page 5 Upta quam: nonsectem aut vella et facerovit, undipsunt pel ipsa quidenimusam labore nit quas eici conet modite quae porio dis preritenihil et plique di aligendi omnia sunt maionse quature rumquaera aliqui odit. 98.0 (3.86) 13.0 (0.51) 70.0 (2.76) Drawing dimensions are in mm (inches). MSP-103 Design developments may result in specification changes. MSP-153 200.0 [7.87] 15.0 [0.59] MOUNTING: 2 OFF M4 STUDS; LENGTH AND POSITION AS SHOWN DIMENSIONS mm (in) 13.5 [0.53] 15.0 [0.59] 54.0 [2.13] 81.0 [3.19] 47.0 [1.85] Page 6 98.0 [3.86] 13.0 [0.51] 70.0 [2.76] Drawing dimensions are in mm (inches). MSP-203 Design developments may result in specification changes. 210.0 (8.26") 9.7 (0.38") 20.0 (0.78") 46.0 (1.81") Page 7 Upta quam: nonsectem aut vella et facerovit, undipsunt pel ipsa quidenimusam labore nit quas eici conet modite quae porio dis preritenihil et plique di aligendi omnia sunt maionse quature rumquaera aliqui odit. 120.0 (4.72") 30.0 (1.18") 65.7 (2.58") 26.7 (1.05") For international contact information, visit advanced-energy.com. ENG-HV-MSP-230-03 08.16 ® ® Specifications are subject to change without notice. ©2015 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy , AE , HiTek Power®, and HiTek Power Ltd.® are U.S. trademarks of Advanced Energy Industries, Inc.