ADVANCED ENERGY OL600W-403P

HITEK POWER® OL600W SERIES 600 W HIGH VOLTAGE POWER SUPPLIES AC-to-HVDC single-output rack-mount high voltage power supplies P Pa ag ge 2 e 2 The OL600W series range of single output high voltage power supplies meets the exacting requirements found in electron beam, ion beam, and x-ray systems, as well as ion and chemical vapor deposition, electrostatic precipitation, and other 24/7 production processes. Features Typical Applications › Output voltages from › Electron beam 1 to 80 kV › Ion beam › High packing density: 600 W › X-ray in 1 U (80 kV 2 U) › Lasers › High stability › HV pulse generator bias › Exceptional reliability › HV amplifier bias › Arc count and extinguish (ACE) › Electrostatic precipitation › Full local and remote control › Chemical purification monitoring › Voltage or current control › Complies with SEMI F47 standard › CE marked for EU LV directive 2006/95/EC › RoHS compliant to EU directive 2011/65/EU › Custom options available Designed using the latest power switching IGBTs to ensure efficient and reliable operation over the full operating range, the OL600W series gives excellent performance in the most severe electrical environments. The OL600W utilizes air as the primary insulation medium for voltages up to 80 kV; 3 achieving a high packing density for high voltage supplies giving 65 W per liter, 1 W per inch . The 1 U construction (2 U for 80 kV units) allows operation at full power when close mounted in a standard equipment rack, saving significant rack space in large systems. Featuring a proprietary Arc Count and Extinguish (ACE) system for managing systems where load arcing, is possible, the OL600W protects both itself and the load from damage that may be caused by excessive arcing, while allowing normal operation to continue. Page 3 PHYSICAL SPECIFICATIONS 600 W max at full rated output voltage and current Output Power Units available with max output from 1 to 80 kV Output Voltage Up to 600 mA for 1 kV and 7.5 mA for 80 kV, see page 5 table Output Current Input Voltage 185 to 255 VAC or 103 to 127 VAC (auto range selection). Range does not change after power up. 47 to 63 Hz single phase and earth. Input Current Not exceeding 6 A (185 to 255 VAC) rms Not exceeding 12 A (103 to 127 VAC) rms Positive or negative to order Polarity Specifications apply above 5% of rated output voltage Specification Range Voltage Ripple Voltage Mode < 0.1% of rated output voltage +2 V pk to pk < 0.02% of rated output voltage +0.5 V rms < 0.5% of rated output voltage +2 V Current Mode pk to pk < 0.1% of rated output voltage +0.5 V rms Voltage Regulation < 0.05% ±0.5 V change in output voltage for a 10% change in line voltage Line < 0.05% ±0.5 V change in output voltage for 0 to 100% change in load current Load Current Regulation < 0.5% of rated output current for a 10% change in line voltage Line < 0.5% of rated output current for 0 to 100% change in output voltage Load Recovery Time < 500 ms to within 0.1% of previous operating level following a short circuit or arc. Max overshoot 2% of rated output voltage. Temperature Coefficient < 100 ppm/°C < 0.1% in 8 h after 3 h warmup at constant load, line, and temperature Drift > 75% Efficiency Over temperature Protection Over voltage Fan failure Current limit Series output resistance Each time the ACE system detects an arc, it blanks the supply off for a brief period to extinguish the arc. The Arc Count and Extinguish unit is then allowed to recover. If more arcs occur, they are counted to determine the arc rate; if this exceeds a (ACE) safe level, the power supply is shut down. The parameters are factory set. 0 to +40°C (32 to 140°F) Operating Temperature Storage Temperature -20 to +70°C (-4 to 158°F) 80% max relative humidity up to 31°C (37°F) reducing linearly to 50% at 40°C (104°F). Non-condensing. Humidity Sea level to 2000 m (6500'). Altitude CE marked to meet the requirements of the Low Voltage Directive, 2006/95/EC, by complying with BS Safety EN61010-1 when installed as a component part of compliant equipment. Equipment Class 1 Safety Class Indoor use only Usage Installation Category II (BS EN61010) 2 (BS EN61010) Pollution Degree Non-portable Portability Page 4 PHYSICAL SPECIFICATIONS Intended for installation as a component of a system and designed to meet: EMC BS EN55022 class B for conducted and radiated emissions BS EN61000-4-2 ESD – levels ±4 kV contact, ±8 kV air discharge BS EN61000-4-4 Fast transients on mains input – levels ±2 kV BS EN61000-4-5 Surges – levels ±2 kV line to earth, ±1 kV line to line BS EN61000-4-8 Magnetic fields – levels 30 A/m at 50/60 Hz BS EN61000-4-11 Voltage dips, interruptions The unit will not trip and recovers to normal operation after a disturbance as defined in SEMI F47. The EMC performance of the power supply can only be fully assessed when installed within and as part of the final system. RoHS Meets the requirements of EU Directive 2011/65/EU on the Restriction of use of certain Hazardous Substances (RoHS) in electrical and electronic equipment. Metering Provided as part of an alphanumeric display. Voltages are displayed with a resolution > 0.5% of rated output. Current is displayed with a resolution of > 1.5% of rated output. Voltage and current set values can be displayed by pressing the relevant control potentiometer. Uses the alphanumeric display to show the reason for any trip condition Status indication Fan assisted with fan fail detection. Air inlets at the rear of the unit, exhaust on the side panels and top cover. Cooling Min air flow required is 3 m/s at the input to the fan. For slide mounting, a 15 mm gap shall be provided above the unit for air exhaust if the side air vents are blocked. For shelf mounting the 1 U, no gap is required above or below the unit provided the side air vents are clear by at least 15 mm. The 2 U requires a 15mm gap above the unit as well. Mechanical Specifications See outline drawing Dimensions 6.5 kg for units up to 60 kV Weight 8 kg for the 80 kV unit All connecions are mounted on the rear panel Connections IEC320-C20 16 A with integrated two pole switch Mains M5 stud Safety Earth Proprietary coaxial connector HV Output Front Panel Stoving enamel trimite full gloss S60/9 color blue RAL5011 as standard. Page 5 INTERFACE CONNECTIONS Remote control 25-way female D-type connector: All logical indicators are open collector outputs rated at 16 V (max) in the off state. An internal 100 Ω resistor is connected in series with the open collector transistor. The pull down voltage is 0.9 V plus the internal resistor drop. The rated current is 10 mA. All analog voltage and current monitors are 0 to +10 V ±0.5% ±20 mV, with respect to pin 13, representing 0 to rated output. Signal impedance < 100 Ω and minimum external load resistance is 2 kΩ. All analog voltage and current inputs are 0 to +10 V on the HI input with respect to the LO input representing 0 V to rated output ±0.2% of setting ±0.1% of rating. Input impedance > 50 kΩ. These component power supplies meet the requirements of EC Directive 2006/95/EC (LVD) Page 6 Note: Drawing dimensions are in mm (") Page 7 EARTH STUD USER INTERFACE D-TYPE SOCKET HV OUTPUT Note: Drawing dimensions are in mm (") SWITCHED 422.8 MAINS INLET [16.6] M4 FIXING BUSHES AIRFLOW 8 POSITIONS 42.8 OBROUND SLOTS [1.7] 10.3 x 7.1 4 POSITIONS 8.6 465.4 [0.3] [18.3] 482.6 [19.0] Page 8 88.1 40.0 [3.5] [1.6] 3.0 496.9 33.5 [0.1] [19.6] [1.3] 85.6 5.9 76.2 [3.4] [0.2] [3.0] 20.2 152.4 108.0 196.8 [0.8] [6.0] [4.3] [7.7] The standard range of units available is as follows: OUTPUT AND ORDERING INFORMATION Model Output Voltage Output Current 1 kV 600 mA OL600W-102* 5 kV 120 mA OL600W-502* 10 kV 60 mA OL600W-103* OL600W-203* 20 kV 30 mA 30 kV 20 mA OL600W-303* 40 kV 15 mA OL600W-403* 50 kV 12 mA OL600W-503* 60 kV 10 mA OL600W-603* OL600W-803* 80 kV** 7.5 mA * Add P for a positive polarity unit or N for a negative polarity unit. eg: part number for a 20 kV positive unit: OL600W-203P ** 80 kV unit utilizes an encapsulated HV section and is housed within a 2 U chassis. For voltages not listed above, please contact our sales team. Page 9 For international contact information, visit advanced-energy.com. ENG-HV-OL600W-230-01 10.16 Specifications are subject to change without notice. ©2016 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, HiTek Power®, and HiTek Power Ltd.® are U.S. trademarks of Advanced Energy Industries, Inc.