ADVANCED ENERGY XR1000/903

HITEK POWER XR1000 1 KW X-RAY POWER SUPPLY MODULE Component power supply for industrial x-ray systems, elemental analysis equipment, x-ray diffraction spectrometers, and materials process monitoring applications Page 2 The XR1000 series is a component power supply for industrial x-ray systems, elemental analysis equipment, x-ray diffraction spectrometers, and materials process monitoring applications. It incorporates a floating filament supply that is automatically controlled by the integral beam loop. It is based on the proven HiTek Power IGBT converter, ensuring high efficiency and reliable operation. The XR1000 units are available with either an analog or RS-232 control interface. FEATURES — 1 KW OF OUTPUT POWER — HIGH-ACCURACY BEAM CURRENT CONTROL — EXTENSIVE TUBE PROTECTION FACILITIES — LOW RIPPLE — ROBUST IGBT CONVERTER DESIGN — ANALOG OR RS-232 INTERFACE — SHORT-CIRCUIT AND OVERLOAD PROTECTION — CE MARKED FOR EU LV DIRECTIVE 2006/95/EC — HIGH STABILITY Typical Applications: • X-Ray Fluorescence (XRF) • X-Ray Diffraction (XRD) • X-Ray Reflectivity (XRR) • X-Ray Imaging (XRI) Page 3 Note: Please contact AE for information about custom versions for specific requirements. SPECIFICATION 1 kW, max, at full rated output voltage and current Output Power 0 to -60 kV or 0 to -90 kV Output Voltage 60 kV unit: 0 to 16 mA Output Current 90 kV unit: 0 to 11 mA 230 VAC ±10% (207 to 253 VAC) 47 to 63 Hz, single phase and earth Input Voltage Not exceeding 12A Input Current RMS Negative Polarity Specifications apply above 5% of rated output voltage and current Specification Range < 0.25% of setting plus 0.25% of rating, peak to peak Ripple Each time the ACE system detects an arc, it blanks the supply off for a brief period to extinguish the arc. The unit is then Arc Count and Extinguish allowed to recover. If more arcs occur, they are counted to determine the arc rate; if this exceeds a safe level, the power (ACE) supply is shut down. The parameters are factory set. Provided as part of an alphanumeric display; Voltages are displayed with a resolution better than 0.5% of rated output. Metering Current is displayed with a resolution of better than 1.5% of rated output The alphanumeric display shows the status of the interlock and the reason for any trip condition. Status Indication Voltage Regulation < 0.05% change in output voltage for a 10% change in line voltage Line < 0.05% change in output voltage for a 5 to 100% change in output current Static Load < 5% change in output voltage for a 5 to 100% change in output current, recovery to within 1% of previous setting within Dynamic Load 200 msec Beam Current Regulation < 0.05% change in output current for a 10% change in line voltage Line < 0.05% change in output current for a 60% change in rated output voltage Load Stability and Drift < 100 ppm/°C Temperature Coefficient < 0.1% of rating over an eight-hour period after 30 min warmup Drift Filament Specification 8 VDC, max, referenced to the negative output voltage Voltage 0.5 to 5 ADC Current Environmental 0 to +40°C (50 to 104°F) Operating Temperature -20 to +70°C (-4 to 158°F) Storage Temperature 80% max relative humidity up to 31°C (88°F), reducing linearly to 50% at 40°C (104°F); non-condensing (ref BS Humidity EN61010-1) Sea level to 2000 m (6500') Altitude Fan assisted with fan fail detection. Air inlets at the sides of the unit with exhaust on the rear panel. Minimum air flow Cooling required is 3 m/sec at the air intake on the side panels. Indoor use only Usage II (BS EN61010) Installation Category 2 (BS EN61010) Pollution Degree Non-portable Portability Safety, Protection, and Compliance This power supply is intended for installation as part of a system. Basic EMC filtering is provided. EMC The XR1000 is currently built to non-RoHS standard. This unit can, however, be configured to meet the requirements RoHS of RoHS where significant customer demand requires it, although please note that this will have an impact on delivery timescales. Over-temperature Protection Over-voltage Fan failure detection Filament current limit Series output resistance Page 4 SPECIFICATION Meets the requirements of the Low Voltage Directive (LVD), 2006/95/EC, by complying with BS EN61010-1 when Safety installed as a component part of other equipment and is CE marked accordingly Equipment class 1 Safety Class Mechanical See outline drawing on page 6. Dimensions 33 kg (73 lb) Weight OUTPUT AND ORDERING INFORMATION Model Output Voltage Output Current -60 kV -16 mA XR1000/603 -90 kV -11 mA XR1000/903 INTERFACE CONNECTIONS IEC320-C20 16 A Mains M5 stud Safety Earth R10, 100 kV receptacle on rear of unit (cable available separately) HV Output Terminal C: HV output Terminal L: Filament Terminal S: No connection Remote Interlock 9-Way, X-RAY ENABLED NO 1 6 HV OUTPUT NO male, D-Type Connector 2 INTERLOCK HV OUTPUT 7 X-RAY ENABLED 3 8 HV OUTPUT NC INTERLOCK 4 NO CONNECTION 9 X-RAY ENABLED NC 5 X-ray enabled and HV output are both a set of isolated changeover contacts. Interlock is an input; shorting the pins closes the interlock. Digital Remote Control NO CONNECTION 1 6 NO CONNECTION 9-Way, Female, D-Type TXD 2 7 NO CONNECTION Connector RXD 3 8 NO CONNECTION NO CONNECTION 4 9 NO CONNECTION 0 V 5 RS-232 Interface 9600 Baud, 8 bit, 1 start, 1 stop, no parity Analog Remote Control OVER-VOLTAGE INDICATION 1 25-Way, Female, D-Type 14 mA MONITOR OVER-TEMPERATURE INDICATION 2 connector 15 BEAM I DEMAND kV MONITOR 3 16 FILAMENT I LIMIT TRIP INDICATION 4 17 EXCESSIVE ARCING INDICATION HV ON/OFF Hi 5 18 FILAMENT STANDBY Hi mA PROGRAM MONITOR 6 19 FILAMENT STANDBY Lo kV PROGRAM MONITOR 7 20 FILAMENT I MONITOR FILAMENT V MONITOR 8 21 FILAMENT OC INDICATION HV ON/OFF Lo 9 FILAMENT I LIMIT INDICATION 22 kV DEMAND 10 23 0 V INTERLOCK CLOSED INDICATION 11 24 mA LIMIT NO CONNECTION 12 25 0 V NO CONNECTION 13 These component power supplies meet the requirements of EC Directive 2006/95/EC (LVD). NOTES: • All logical indicators are open collector outputs rated at 16 V (max) in the off state. An internal 100 Ω resistor is connected in series with the open collector transistor. The pull down voltage is 0.9 V plus the internal resistor drop. The rated current is 10 mA. • All analog voltage and current monitors are 0 V to +10 V ±0.5% ±20 mV, with respect to 0 V, representing 0 to rated output. Signal impedance is less than 100 Ω and minimum external load resistance is 2 kΩ. • All analog voltage and current inputs are 0 to +10 V with respect 0 V, representing 0 V to rated output ±0.2% of setting ±0.1% of rating. Input impedance is greater than 50 kΩ. Page 5 Interlock Output Drawing dimensions are in mm (inches). Design developments may result in specification changes. Airflow Mains Interface 432.4 (17.0) 482.6 (19.0) 8.63 465.5 (0.34) (18.3) AE World Headquarters 1625 Sharp Point Drive Fort Collins, Colorado 80525 1 800 446 9167 +1 970 221 4670 sales.support@aei.com advanced-energy.com ENG-HV-XR10000-230-01 11.15 Specifications are subject to change without notice. ©2015 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy® and AE® are U.S. trademarks of Advanced Energy Industries, Inc. 132.5 43.6 (5.21) (1.72) 88.9 2.0 532.0 (3.5) (0.08) (20.9)