CRYDOM 10PCV2490

Control Relays Datasheet PCV Series • Proportional controller • Ratings from 15 A to 90 A @ 280 VAC • 2-7 VDC or 2-10 VDC analog input range • For use with resistive loads only PRODUCT SELECTION Descrption 15 A 25 A 50 A 75 A 90 A 2-7 VDC Control 7PCV2415 7PCV2425 2-10 VDC Control 10PCV2415 10PCV2425 10PCV2450 10PCV2475 10PCV2490 OUTPUT SPECIFICATIONS (1) Description 15 A 25 A 50 A 75 A 90 A Operating Voltage (47-63Hz) [Vrms] 100-280 100-280 100-280 100-280 100-280 Transient Overvoltage [Vpk] 600 600 600 600 600 Maximum Off-State Leakage Current @ Rated Voltage [mArms] 10 10 10 10 10 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] 200 200 200 200 200 Maximum Load Current [Arms] 15 25 50 75 90 Minimum Load Current [Arms] 0.15 0.15 0.15 0.15 0.15 Maximum Surge Current (16.6ms) [Apk] 150 250 625 1000 1200 Maximum On-State Voltage Drop @ Rated Current [Vpk] 1.6 1.6 1.6 1.6 1.6 Maximum I² t for Fusing (8.3 msec) [A² sec] 94 260 1620 4150 6000 Minimum Power Factor (with Maximum Load) 0.5 0.5 0.5 0.5 0.5 INPUT SPECIFICATIONS (1) Description 7PCV24xx 10PCV24xx Control Voltage Range 2-7 VDC 2-10 VDC Typical Input Current @ 5 VDC 4 mA 4 mA GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Signal to Load (50/60Hz) 2500 Vrms Dielectric Strength, Signal to Base 2500 Vrms Ambient Operating Temperature Range -30 to 80 °C Ambient Storage Temperature Range -40 to 125 °C Weight (typical) 3.5 oz. (100g) Encapsulation Themaly Conductive Epoxy Terminals Screws and Saddle clamps Furnished, Unmounted GENERAL NOTES (1) All parameters at 25°C unless otherwise specified. Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice. Control Relays Datasheet MECHANICAL SPECIFICATIONS 1.10 (27.9) MOUNTING HOLE/SLOT 8-32 TERMINAL .45 0.192 (4.9) DIA. (2 PLACES ) (11.4) Screw Torque Requirements: 6-32 Screws - 10 in. lbs., OUTPUT 2.30 8-32 and 10-32 Screws - 20in. lbs. 1 2 (58.4) (Screws dry without grease.) 1.87 1.70 (47.5) (43.2) -- + 4 3 INPUT 1.00 .78 BASE PLATE (25.4) 6-32 TERMINAL (19.8) .125 (3.2) (2 PLACES) .9 1.80 (45.7) (23.0) All dimensions are in inches (millimeters) WIRING DIAGRAM 7PCV24XX 100 80 60 ~ 60 Hz 40 20 0 0 1 2 3 4 5 6 7 1 OUTPUT 2 Input Voltage PROPORTIONAL CONTROLLER 10PCV24XX 4 3 INPUT 100 80 60 + -- 60 Hz 40 20 0 0 1 2 3 4 5 6 7 8 9 10 Input Voltage Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice. True RMS Output Voltage True RMS Output Voltage as a Percentage of Line Voltage as a Percentage of Line Voltage Control Relays Datasheet THERMAL DERATE INFORMATION 15A 25A 50A 15 30 95 60 1°C/W 1°C/W .5°C/W 90 2°C/W 112 25 100 1.5°C/W 3°C/W 4°C/W 2°C/W 10 20 40 100 6°C/W 116 2°C/W 15 110 110 NO HEATSINK 120 5 10 20 NO HEATSINK 5 120 NO HEATSINK 120 124 0 0 0 3 6 9 12 15 20 40 60 80 5 10 15 20 25 20 40 60 80 10 20 30 40 50 20 40 60 80 Load Current [Arms] Max Ambient Temp. [°C] Load Current [Arms] Max Ambient Temp. [°C] Load Current [Arms] Max Ambient Temp. [°C] 75A 90A 90 90 120 .5°C/W .2°C/W 95 .5°C/W .3°C/W .4°C/W 100 100 60 80 1°C/W 1°C/W 110 110 30 40 120 120 0 0 15 30 45 60 75 20 40 60 80 20 40 60 80 0 20 40 60 80 Load Current [Arms] Max Ambient Temp. [°C] Load Current [Arms] Max Ambient Temp. [°C] TYPICAL APPLICATIONS • Industrial temperature controllers • Light dimming • Vibratory feeders • Resistive heating elements • Rectified DC motors • Conveyor speed control UNSUITABLE APPLICATIONS The PCV is not suitable for some load applications Including, but not limited to the following: • AC motor control • Three Phase motors • Transformers requiring pure sine wave input • Zero crossing applications Please contact Crydom’s application Engineering department for additional Information and specific application questions. AGENCY APPROVALS Agency Approvals E116950 LR81689-73 Rev. 022218 ECN#20419 Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice. Power Dissipation Power Dissipation Base Plate Temp [°C] Power Dissipation Base Plate Temp [°C] Power Dissipation Base Plate Temp [°C] Power Dissipation Base Plate Temp [°C] Base Plate Temp [°C] Control Relays Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH. EXPLOSION. • Eteindre • 在操作此设 • Desconectar • Spenga tutta • Disconnect all • Stellen Sie toutes les todos los l'alimentazione 备之前请先 power before jeglichen sources suministros de che fornisce 关闭电源。 installing or Strom ab, der d'énergie de energia a este questa working with dieses Gerät cet appareil equipo antes apparecchiatura 若不遵守这些说明， this equipment. versorgt, bevor de trabajar avant de prima di lavorare 可能会导致严重的 Sie an dem con este equipo. travailler a questa • Verify all Gerät Arbeiten 人身伤害甚至死亡。 dessus de cet apparecchiatura connections • Verificar todas durchführen appareil and replace all las conexiones • Verificare tutti • Vor dem covers before y colocar todas i collegamenti • Vérifier tous Drehen auf turning on e sostituire las tapas antes connections, et Energie alle power. de energizer remettre tous tutte le coperture Anschlüsse prima el equipo. couverts en überprüfen Failure to follow dell’accensione olace avant de und alle these El mettre sous Abdeckungen instructions will L'omissione di incumplimiento ersetzen. De non-suivi de result in death queste istruzioni de estas ces instructions or serious injury. provocherà la Unterlassung instrucciones provoquera la morte o dieser puede provocar mort ou des lesioni serie Anweisungen la muerte o lésions sérieuses können zum lesiones serias. sérieuses. Tode oder zu schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISQUE DE DOMMAGE MATERIEL ET DE GEFAHR VON MATERIALSCHÄDEN UND RISK OF MATERIAL DAMAGE AND HOT SURCHAUFFE DU BOITIER GEHÄUSEERHITZUNG ENCLOSURE • Les panneaux latéraux du produit peuvent être • Die Seitenwände können heiß sein. Lassen Sie • The product's side panels may be hot, allow chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. the product to cool before touching. toucher. • Beachten Sie die Montageanweisungen, • Follow proper mounting instructions including • Respecter les consignes de montage, et • Führen Sie keine Flüssigkeiten oder torque values. notamment les couples de serrage. Fremdkörper in das Produkt ein. • Do not allow liquids or foreign objects to enter • Ne pas laisser pénétrer de liquide ni de corps this product. étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE RISCHIO DI DANNI MATERIALI E D'INVOLUCRO 材料损坏和高温外壳的危险性 SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Respetar las instrucciones de montaje, y en • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice. Control Relays Datasheet ANNEX - ENVIRONMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice.