CRYDOM 10SST120

Control Relays DataSheet SST Series • Soft-start modules • 120/240 V AC models • 3.5-10 V DC control range • Used with Series 1 random-fire solid-state relays PRODUCT SELECTION 25 A 50 A 75 A Description 10 A 90 A 120 Vrms Line Voltage 10SST120 25SST120 40SST120 240 Vrms Line Voltage 10SST240 25SST240 50SST240 75SST240 90SST240 (1) OUTPUT SPECIFICATIONS(voltage) Description 120 VAC 240 VAC Operating Voltage (47-63Hz) [Vrms] 90-140 180-280 Transient Overvoltage [Vpk] 400 600 Maximum Off-State Leakage Current @ Rated Voltage [mArms] 10 10 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (2) 500 500 (1) OUTPUT SPECIFICATIONS(current) Description 10 A 25 A 50 A 75 A 90 A Maximum Load Current (3) [Arms] 25 50 10 75 90 Minimum Load Current (3) [Arms] 0.04 0.04 0.04 0.04 0.04 Maximum Surge Current (16.6ms) [Apk] 120 250 625 1000 1200 1.6 1.6 Maximum On-State Voltage Drop @ Rated Current [Vpk] 1.6 1.6 1.6 Thermal Resistance Junction to Case (Rjc) [°C/W] 1.48 1.02 0.63 0.31 0.28 Maximum I²t for Fusing (8.3 msec) [A²sec] 60 260 1620 4150 6000 Minimum Power Factor (with Maximum Load) 0.5 0.5 0.5 0.5 0.5 (1) CONTROL MODULE INPUT SPECIFICATIONS Description DC Control Control Voltage Range 3.5-10 VDC Must Turn On Voltage 1.0 VDC Must Turn Off Voltage 1.6 mA @ 5 VDC 150 msec Typical Input Current @ 5 VDC Nominal Input Impedance 180 msec Maximum Turn-on Time [msec] (3) 0.1 msec Maximum Turn-Off Time [msec] 1/2 Cycle (1) CONTROL MODULE OUTPUT SPECIFICATIONS Description DC Control Maximum Off-State Operating Voltage 36 VDC Maximum Load Current 3 mADC Maximum Turn-On Voltage@ 3mA 0.5 VDC Maximum Off-State Leakage@ 10 VDC 1.0 µADC Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Obsolete Control Relays DataSheet (1) GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, signal to load 4000 Vrms Dielectric Strength, signal to Base 4000 Vrms Ambient Operating Temperature Range -30 to 80 °C Ambient Storage Temperature Range -40 to 125 °C Weight (typical) 3.0 oz. (43g) Encapsulation Thermally Conductive Epoxy GENERAL NOTES (1) All parameters at 25°C unless otherwise specified. (2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 (3) Heat sinking required (Relay Only). WIRING DIAGRAM Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] NOTES (1) Following pins may be interchanged: 1A & 1B, 2A & 2B, 3A & 3B. (2) Pin 4A & 4B may not be interchanged (3) The line and load may be interchanged. Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Obsolete Control Relays DataSheet THERMAL DERATE INFORMATION AGENCY APPROVALS Agency Approvals UL E116949 Rev. 122010 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Obsolete Control Relays DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH. EXPLOSION. • Eteindre • 在操作此设 • Desconectar • Spenga tutta • Disconnect all • Stellen Sie toutes les todos los l'alimentazione 备之前请先 power before jeglichen sources suministros de che fornisce 关闭电源。 installing or Strom ab, der d'énergie de energia a este questa working with dieses Gerät cet appareil equipo antes apparecchiatura 若不遵守这些说明， this equipment. versorgt, bevor de trabajar avant de prima di lavorare 可能会导致严重的 Sie an dem con este equipo. travailler a questa • Verify all Gerät Arbeiten 人身伤害甚至死亡。 dessus de cet apparecchiatura connections • Verificar todas durchführen appareil and replace all las conexiones • Verificare tutti • Vor dem covers before y colocar todas i collegamenti • Vérifier tous Drehen auf turning on e sostituire las tapas antes connections, et Energie alle power. de energizer remettre tous tutte le coperture Anschlüsse prima el equipo. couverts en überprüfen Failure to follow dell’accensione olace avant de und alle these El mettre sous Abdeckungen instructions will L'omissione di incumplimiento ersetzen. De non-suivi de result in death queste istruzioni de estas ces instructions or serious injury. provocherà la Unterlassung instrucciones provoquera la morte o dieser puede provocar mort ou des lesioni serie Anweisungen la muerte o lésions sérieuses können zum lesiones serias. sérieuses. Tode oder zu schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISQUE DE DOMMAGE MATERIEL ET DE GEFAHR VON MATERIALSCHÄDEN UND RISK OF MATERIAL DAMAGE AND HOT SURCHAUFFE DU BOITIER GEHÄUSEERHITZUNG ENCLOSURE • Les panneaux latéraux du produit peuvent être • Die Seitenwände können heiß sein. Lassen Sie • The product's side panels may be hot, allow chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. the product to cool before touching. toucher. • Beachten Sie die Montageanweisungen, • Follow proper mounting instructions including • Respecter les consignes de montage, et • Führen Sie keine Flüssigkeiten oder torque values. notamment les couples de serrage. Fremdkörper in das Produkt ein. • Do not allow liquids or foreign objects to enter • Ne pas laisser pénétrer de liquide ni de corps this product. étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE RISCHIO DI DANNI MATERIALI E D'INVOLUCRO 材料损坏和高温外壳的危险性 SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Respetar las instrucciones de montaje, y en • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Obsolete Control Relays DataSheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Obsolete