PCB Mount DataSheet ASPF Series • Mini-SIP SSR • Ratings to 3A @ 280 VAC • SCR output • DC control • Zero-crossing (resistive loads) or random-fire (inductive loads) output PRODUCT SELECTION Control Voltage Zero Crossing Random Fire 4-10 VDC ASPF240D3 ASPF240D3R (1) OUTPUT SPECIFICATIONS Description Operating Voltage (47-63Hz) [Vrms] 24-280 24-280 Transient Overvoltage [Vpk] 600 600 Maximum Off-State Leakage Current @ Rated Voltage [mArms] 0.1 0.1 3.0 3.0 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/μsec] (3) 0.1 0.1 Maximum Load Current [Arms] Minimum Load Current [Arms] 60 100 Maximum Surge Current (16.6ms) [Apk] 40 40 Maximum On-State Voltage Drop @ Rated Current [Vpk] 1.5 1.5 0.5 0.5 Minimum Power Factor (with Maximum Load) (1) INPUT SPECIFICATIONS Description Control Voltage Range 4-10 VDC Must Turn On Voltage 4.0 VDC Must Turn Off Voltage 1.0 VDC Typical Input Current @ 5 VDC 15 mAdc 300 Ohm Nominal Input Impedance Maximum Turn-On Time [msec] (4) 1/2 Cycle Maximum Turn-Off Time [msec] 1/2 Cycle GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) (2) 3750 Vrms 9 Minimum Insulation Resistance (@ 500 VDC) (2) 10 Ohms Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -30ºC to 80ºC Ambient Storage Temperature Range -30ºC to 125ºC Weight (typical) 0.35 oz. (10g) Encapsulation Thermally Conductive Epoxy GENERAL NOTES 1) All parameters at 25°C unless otherwise noted. 2) Dielectric and insulation resistance are measured between input and output. 3) Off-State dv/dt test method per EIA/NARM standard RS-443. 4) Turn-On time for random turn-on versions is 0.01 msec (DC C Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. LOAD LOAD PCB Mount DataSheet WIRING DIAGRAM TRIGGER CIRCUIT 2 3 1 4 +DC -DC B A AC AC Load can be wired in location A or B THERMAL DERATE INFORMATION 3.0 2.5 2.0 1.5 1.0 0 20 40 60 80 AMBIENT TEMPERATURE (ºC) Max. Load Current vs. Temp. Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. LOAD CURRENT (AMPS) PCB Mount DataSheet MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm DC CONTROL. All dimensions are in: inches [millimeters] PIN 1: AC LOAD PIN 2: AC LOAD PIN 3: +DC CONTROL PIN 4: -DC CONTROL .95 .66 (24.1) (16.8) .93 TYP. (23.6) .25 (6.4) 1 2 3 4 .15 .100 .030 (2.5) (0.8) (0.4) .500 (12.7) .700 (17.8) AGENCY APPROVALS Agency Approvals E116950 LR81689 Rev. 061608 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. PCB Mount DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 SCOSSA ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH. EXPLOSION. • 在操作此设 • Eteindre • Spenga tutta • Desconectar • Disconnect all • Stellen Sie toutes les l'alimentazione todos los 备之前请先 power before jeglichen sources che fornisce suministros de 关闭电源。 installing or Strom ab, der d'énergie de questa energia a este working with dieses Gerät cet appareil apparecchiatura equipo antes 若不遵守这些说明， versorgt, bevor this equipment. avant de prima di lavorare de trabajar Sie an dem 可能会导致严重的 travailler a questa con este equipo. • Verify all Gerät Arbeiten 人身伤害甚至死亡。 dessus de cet apparecchiatura connections • Verificar todas durchführen appareil and replace all las conexiones • Verificare tutti • Vor dem covers before y colocar todas • Vérifier tous i collegamenti Drehen auf turning on las tapas antes connections, et e sostituire Energie alle power. de energizer tutte le coperture remettre tous Anschlüsse prima el equipo. couverts en überprüfen Failure to follow dell’accensione olace avant de und alle these El mettre sous Abdeckungen instructions will L'omissione di incumplimiento ersetzen. result in death De non-suivi de queste istruzioni de estas or serious injury. ces instructions provocherà la Unterlassung instrucciones provoquera la morte o dieser puede provocar mort ou des lesioni serie Anweisungen la muerte o lésions sérieuses können zum lesiones serias. sérieuses. Tode oder zu schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISQUE DE DOMMAGE MATERIEL ET DE GEFAHR VON MATERIALSCHÄDEN UND RISK OF MATERIAL DAMAGE AND HOT SURCHAUFFE DU BOITIER GEHÄUSEERHITZUNG ENCLOSURE • Les panneaux latéraux du produit peuvent être • Die Seitenwände können heiß sein. Lassen Sie • The product's side panels may be hot, allow chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. the product to cool before touching. toucher. • Beachten Sie die Montageanweisungen, • Follow proper mounting instructions including • Respecter les consignes de montage, et • Führen Sie keine Flüssigkeiten oder torque values. notamment les couples de serrage. Fremdkörper in das Produkt ein. • Do not allow liquids or foreign objects to enter • Ne pas laisser pénétrer de liquide ni de corps this product. étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE RISCHIO DI DANNI MATERIALI E D'INVOLUCRO 材料损坏和高温外壳的危险性 SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Respetar las instrucciones de montaje, y en • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. PCB Mount DataSheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.