Panel Mount Datasheet Evolution Dual Series • 25A & 50A Output rating per channel @ 40°C • 24 to 280 & 48 to 600VAC Operating voltage • 4-32VDC Control input • Three input termination options • Zero turn-on outputs • Input status LED indicator for each channel • Available with IP20 “Touch-Safe” Covers • UL508 Endurance Rating PRODUCT SELECTION Control Voltage 240V, 25A 240V, 50A 480V, 25A 480V, 50A 4-32 VDC CD2425W2U CD2450W2U CD4825W2U CD4850W2U AVAILABLE OPTIONS Output Terminal Orientation U: A channel top, Operating Voltage B channel bottom 24: 24-280 VAC Control Voltage V: A channel on left, Series 48: 48-600 VAC W: 4-32 VDC B channel on right C D 24 25 W 2 V H Cover Rated Load Current Input Connector Thermal Pad C: Included 25: 25 Amps 2: Key Locking Connector Blank: Not Included D: Not Included 50: 50 Amps 3: 4 Pin Connector H: Included accepting Screw Terminals 4: 4 Pin Spring Terminal Required for valid part number For options only and not required for valid part number * Not all part number combinations are available. Contact Crydom Technical support for information on the availability of a specific part number. (1) OUTPUT SPECIFICATIONS Description Cx2425xxxx Cx2450xxxx Cx4825xxxx Cx4850xxxx Operating Voltage (47-440Hz) [Vrms] 24-280 24-280 48-600 48-600 Load Current Range (3) [Arms] 0.15-25 0.15-50 0.15-25 0.15-50 Transient Overvoltage [Vpk] 600 600 1200 1200 Maximum Off-State Leakage Current @ Rated Voltage [mArms] 1.0 1.0 1.0 1.0 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (2) 500 500 500 500 Maximum 1 Cycle Surge Current (50/60) [Apk] 275/300 710/750 275/300 710/750 Maximum Surge Current 50Hz (20ms) [Apk] 275 710 275 710 Maximum On-State Voltage Drop @ Rated Current [Vpk] 1.3 1.3 1.3 1.3 Thermal Resistance Junction to Case (Rjc) [°C/W] 0.65 0.33 0.65 0.33 Maximum I² t for Fusing 50/60Hz (1/2 cycle) [A² sec] 380/370 2520/2320 380/370 2520/2320 Minimum Power Factor (with Maximum Load) 0.5 0.5 0.5 0.5 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Panel Mount Datasheet (1) INPUT SPECIFICATIONS Description CxxxWxxx Control Voltage Range 4-32 VDC Minimum Turn-On Voltage 4 VDC Minimum Turn-Off Voltage 1 .0 VDC Typical Input Current 10 mA @ 12 VDC Nominal Input Impedance See Note (4) Maximum Turn-On Time [msec] 1/2 Cycle Maximum Turn-Off Time [msec] 1/2 Cycle GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output (50/60Hz) 4000 Vrms Dielectric Strength, Input/Output/Base (50/60Hz) 4000 Vrms 9 Minimum Insulation Resistance (@ 500 V DC) 10 Ohm Maximum Capacitance, Input/Output 10 pF Ambient Operating Temperature Range -40 to 80 °C Ambient Storage Temperature Range -40 to 125 °C Weight (typical) 3.0 oz (86.5 g) Terminals Screw Type Output: 8-32 Max. Torque Output: 20 in lb (2.2Nm) Max. Wire Size Output:2 x AWG 8 (3.8mm) GENERAL NOTES 1) All parameters at 25°C and per section unless otherwise specified. 2) Off-state dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 3) Heat sinking required, see derating curves. 4) Input circuit incorporates active current limitation WIRING DIAGRAM SSR Output Configuration "U" Option Top-Bottom Line/Load Connections LOAD A AC SUPPLY 1 A1 -DC AC LED Trigger Circuit +DC 2 A2 AC Current +A Limiter A -A +B B -B 3 B1 -DC AC LED Trigger Circuit +DC 4 B2 AC Current AC SUPPLY Limiter LOAD B Contactor Output Configuration "V" Option Left-Right Line/Load Connections +A A -A +B B -B L L O O A A D D A B AC SUPPLY AC SUPPLY Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Panel Mount Datasheet MECHANICAL SPECIFICATIONS Tolerances: ± 0.02 in / 0.5 m All dimensions are in: inches [millimeters] Mounting 2.300 [58.42] Mounting Hole/Slot Hole/Slot 1.875 [47.63] r 0.09 [2.2] 0.18 [4.5] .625 [15.89] DIA. 8X .191 [4.85] 1.100 [27.94] IP20 1.425 [36.20] .803 [20.40] 1.700 [43.18] 2X .200 [5.08] 1.800 [45.72] 2.635 [66.93] 2.300 [58.42] 1.100 [27.94] IP00 1.150 [29.21] 1.150 [29.21] .803 [20.40] 1.700 [43.18] 1.800 [45.72] MECHANICAL DIMENSIONS INPUT CONNECTOR DIMENSIONS SUGGESTED MATING (shown without IP20 cover) CONNECTORS/PLUGS 3X 0.100 [2.54] 4X 0.026 [0.66] (SQUARE) Crimp Housing, Positive Latch 1.150 [29.21] 0.200 [5.08] Molex 050579404 0.300 [7.62] 0.120 [3.05] Accepts wires: AWG #24, 0.2 mm² 0.420 [10.67] INPUT CONNECTOR OPTION 2 0.500 [12.71] Vertical Plug, Top Wire entry Molex 039500-0004 Phoenix 1840382 Dinkle EC350V-04P 0.413 [10.50] Vertical Plug, Rear Wire entry 3X 0.138 [3.50] Molex 39503-2004 Phoenix 1862878 0.157 [4.00] Dinkle EC350RL-04P 1.046 [26.58] 1.059 [26.90] 0.285 [7.25] Vertical Plug, Front Wire entry 4X 0.031 [0.80] Molex 39503-3004 0.122 [3.10] (SQUARE) Phoenix 1863178 INPUT CONNECTOR 0.606 [15.40] Dinkle EC350R-04P OPTION 3 Vertical Spring Cage Plug, top Wire E Phoenix 1939934 Dinkle 0221-2004 All 4 options accept wires: AWG #16 to 24 N/A Accepts wires: AWG #16 to 24 1.201 [30.50] INPUT CONNECTOR OPTION 4 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Panel Mount Datasheet THERMAL DERATE INFORMATION CXXX25XXXX CXXX50XXXX (25 Amps per Channel) (50 Amps per Channel) 50 100 40 80 30 60 20 40 10 20 0 0 20 30 40 50 60 70 80 20 30 40 50 60 70 80 Ambient Temperature [°C] Ambient Temperature [°C] 1.0°C/W - HS103 0.5°C/W - HS053 1.5°C/W - HS-2 1.0°C/W - HS103 2.5°C/W - 1.5°C/W - HS-2 AGENCY APPROVALS Approvals Designed in accordance with the requirements of IEC 62314 E116950 Rev. 060916 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Combined Load Current [Amps] Combined Load Current [Amps] Panel Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSI OR ARC FLASH. EXPLOSION. ONE. • Eteindre • 在操作此设 • Desconectar • Disconnect all • Stellen Sie toutes les • Spenga tutta todos los 备之前请先 jeglichen power before sources l'alimentazion suministros de 关闭电源。 installing or Strom ab, der d'énergie de e che fornisce energia a este working with dieses Gerät cet appareil questa equipo antes 若不遵守这些说明， this equipment. versorgt, bevor avant de apparecchiatu de trabajar 可能会导致严重的 Sie an dem ra prima del con este equipo. travailler • Verify all Gerät Arbeiten 人身伤害甚至死亡。 lavorare a questa dessus de cet connections • Verificar todas durchführen appareil apparecchiatu ra and replace all las conexiones • Vor dem covers before • Verificare tutti y colocar todas • Vérifier tous Drehen auf turning on i collegamenti las tapas antes connections, et Energie alle power. e sostituire de energizer remettre tous Anschlüsse tutte le coperture el equipo. couverts en überprüfen Failure to follow prima della olace avant de und alle these El rotazione mettre sous Abdeckungen instructions will incumplimiento sull'alimentazi one ersetzen. De non-suivi de result in death de estas ces instructions L'omissione di or serious injury. Unterlassung instrucciones provoquera la seguire queste dieser puede provocar mort ou des istruz ioni Anweisungen la muerte o provocherà la lésions sérieuses können zum lesiones serias. morte o di sérieuses. Tode oder zu lesioni serie schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISQUE DE DOMMAGE MATERIEL ET DE GEFAHR VON MATERIALSCHÄDEN UND RISK OF MATERIAL DAMAGE AND HOT SURCHAUFFE DU BOITIER GEHÄUSEERHITZUNG ENCLOSURE • Les panneaux latéraux du produit peuvent être • Die Seitenwände können heiß sein. Lassen Sie • The product's side panels may be hot, allow chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. the product to cool before touching. toucher. • Beachten Sie die Montageanweisungen, • Follow proper mounting instructions including • Respecter les consignes de montage, et • Führen Sie keine Flüssigkeiten oder torque values. notamment les couples de serrage. Fremdkörper in das Produkt ein. • Do not allow liquids or foreign objects to enter • Ne pas laisser pénétrer de liquide ni de corps this product. étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE RISCHIO DI DANNI MATERIALI E D'INVOLUCRO 材料损坏和高温外壳的危险性 SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Respetar las instrucciones de montaje, y en • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. Panel Mount Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice.