CRYDOM DRA4D250D6

DIN Rail Mount DataSheet DRA4D Series • DC Motor Reversing Contactor • Ratings of 6 & 12 Amps • Load voltage ratings of 1-100VDC and 1-250VDC • Fits standard 35mm DIN-RAIL • LED input status indicator. Green (Forward), Yellow (Reverse) • DC control • cUL Recognized, IEC Rated, CE & RoHS Compliant • Horsepower Rated PRODUCT SELECTION Control Voltage 12 A 6 A DRA4D250D6 5-15 VDC Control DRA4D100D12 15-32 VDC Control DRA4D100E12 DRA4D250E6 AVAILABLE OPTIONS Load Voltage Current Rating 100: 1-100 VDC 12 A 6: 6 Amps 250: 1-250 VDC 6 A 12: 12 Amps Series DRA 4D D 6 100 Function Control Voltage 4D: H-Bridge D: 5-15 VDC E: 15-32 VDC Required for valid part number For options only and not required for valid part number (1) OUTPUT SPECIFICATIONS DRA4D100x12 DRA4D250x6 Description 1-250 (2) Operating Voltage [VDC] 1-100 (3) 6 (5) Maximum Load Current [Adc] (4) 12 1.0 Minimum Load Current [mAdc] 1.0 20 Maximum Off-State Leakage Current @ Rated Voltage [uA] 1.0 0.1 Maximum On-State Voltage Drop @ Rated Current [Vpk] 0.1 91 Maximum Surge Current (10ms) [Apk] 110 0.45 On-State resistance at rated current (RDSOn) [Ohms] 0.011 Thermal Resistance Junction to Case (Rjc) [°C/W] 0.48 0.45 24/10 24/10 Min/Max stranded/solid wire [AWG] Min/Max stranded/solid wire [IEC mm²] 0.5-4.0 0.5-4.0 HP Rating per UL508 @ 40°C 1/4, 4 FLA @ 90 VDC 1/4, 2 FLA @ 180 VDC 6.0 FLA @ 180 VDC, 1KW IEC 60947-4-1 Ratings DC-1 12 FLA @ 90 VDC, 1KW IEC 60947-4-1 Ratings DC-3 4.0 FLA @ 90 VDC, 360W 2.0 FLA @ 180 VDC, 360W Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice. DIN Rail Mount DataSheet (1) INPUT SPECIFICATIONS Description DRA4DxxxD DRA4DxxxE 15-32 VDC Control Voltage Range 5.0-15 VDC Must Turn On Voltage 15 VDC 5.0 VDC Must Turn Off Voltage 2.5 VDC 2.9 VDC Minimum Input Current [mA] 16 20.5 Maximum Input Current [mA] 24.5 22 See Note 6 Nominal Input Impedance See Note 6 Maximum Turn-On Time [msec] 22 22 Maximum Turn-Off Time [msec] 0.264 0.33 24/12 Min/Max stranded/solid wire 24/12 Min/Max stranded/solid wire [IEC mm²] 0.5-2.5 0.5-2.5 GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) 2500Vrms 9 Minimum Insulation Resistance (@ 500 V DC) 10 Ohms Maximum Capacitance, Input/Output 35 pF @ 1KHz Ambient Operating Temperature Range -30ºC to 60ºC Ambient Storage Temperature Range -30ºC to 85ºC Recommended Terminal Screw Torque: 4.0 in lb (0.45 Nm) GENERAL NOTES (1) All parameters at 25°C unless otherwise specified. (2) UL maximum rated voltage is 180 VDC (3) UL maximum rated voltage is 90 VDC. (4) At 40°C and mounted in vertical position (5) At 40°C single unit, multiple units need spacing of 45mm. No spacing maximum current is 5.5 A (6) Input circuitry incorporates active current limiter. WIRING DIAGRAM + + M1 - - S1 M2 F - + - R S2 Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice. +DC M1 -DC M2 CONTROL +F -F DIN Rail Mount DataSheet THERMAL DERATE INFORMATION DRA4D250D6 DRA4D100x12 6 12 5 10 8 4 6 3 4 2 2 1 0 20 30 40 50 60 0 20 30 40 50 60 Ambient Temperature (ºC) Ambient Temperature (ºC) Rating based on single or multiple relays and no space between units. Rating based on single or multiple relays with 45mm gap between units. For no spacing between relays, maximum current @ 40˚ C is 5.5 A MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] SSR-DC-E12 100V 12A RESISTIVE 1/4HP@90VDC 2.91 [73.9] 1.48 ASSEMBLED [37.7] 1.89 IN MEXICO 24VDC 1102 [48.1] DRA4D100D12 1.48 [37.7] 3.53 1.74 [89.6] [44.1] 2.13 [54.1] AGENCY APPROVALS AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 IEC 61000-4-2 : Electrostatic Discharge – Level 3 IEC 61000-4-4 : Electrically Fast Transients – Level 2 (Criteria A) IEC 61000-4-5 : Electrical Surges - Level 2 (Criteria A) E116949 Rev. 020618 ECN#20400 Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice. Load Current (Amps) Load Current (Amps) DIN Rail Mount DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH. EXPLOSION. • 在操作此设 • Desconectar • Eteindre • Spenga tutta • Disconnect all • Stellen Sie todos los toutes les l'alimentazione 备之前请先 power before jeglichen suministros de sources che fornisce 关闭电源。 installing or Strom ab, der energia a este d'énergie de questa working with dieses Gerät equipo antes cet appareil apparecchiatura 若不遵守这些说明， this equipment. versorgt, bevor de trabajar avant de prima di lavorare 可能会导致严重的 Sie an dem travailler a questa con este equipo. • Verify all Gerät Arbeiten 人身伤害甚至死亡。 dessus de cet apparecchiatura connections • Verificar todas durchführen appareil and replace all las conexiones • Verificare tutti • Vor dem covers before y colocar todas • Vérifier tous i collegamenti Drehen auf turning on las tapas antes connections, et e sostituire Energie alle power. de energizer remettre tous tutte le coperture Anschlüsse el equipo. couverts en prima überprüfen Failure to follow dell’accensione olace avant de und alle these El mettre sous Abdeckungen instructions will L'omissione di incumplimiento ersetzen. result in death De non-suivi de queste istruzioni de estas or serious injury. ces instructions provocherà la Unterlassung instrucciones provoquera la morte o dieser puede provocar mort ou des lesioni serie Anweisungen la muerte o lésions sérieuses können zum lesiones serias. sérieuses. Tode oder zu schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 GEFAHR VON MATERIALSCHÄDEN UND RISQUE DE DOMMAGE MATERIEL ET DE RISK OF MATERIAL DAMAGE AND HOT GEHÄUSEERHITZUNG SURCHAUFFE DU BOITIER ENCLOSURE • Die Seitenwände können heiß sein. Lassen Sie • Les panneaux latéraux du produit peuvent être • The product's side panels may be hot, allow das Produkt abkühlen, bevor Sie es berühren. chauds. Laisser le produit refroidir avant de le the product to cool before touching. • Beachten Sie die Montageanweisungen, toucher. • Follow proper mounting instructions including • Führen Sie keine Flüssigkeiten oder • Respecter les consignes de montage, et torque values. notamment les couples de serrage. Fremdkörper in das Produkt ein. • Do not allow liquids or foreign objects to enter • Ne pas laisser pénétrer de liquide ni de corps this product. étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE 材料损坏和高温外壳的危险性 RISCHIO DI DANNI MATERIALI E D'INVOLUCRO SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Respetar las instrucciones de montaje, y en • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice. DIN Rail Mount DataSheet ANNEX - ENVIRONMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2018 Crydom Inc. Specifications subject to change without notice.