CRYDOM MCPC2425A

Control Relays DataSheet MCPC Series • Microprocessor based proportional controller / SSR • Ratings from 25A to 90A @ 48-530 VAC • Low-voltage, current, or potentiometer control • Output status indicator • Separate output enable / disable control • 0-100% Control Range • For use with resistive loads only PRODUCT SELECTION Control Voltage 25 A 50 A 90 A 40-140 VAC MCPC1225 MCPC1250 MCPC1290 180-280 VAC MCPC2425 MCPC2450 MCPC2490 330-530 VAC MCPC4825 MCPC4850 MCPC4890 AVAILABLE OPTIONS Analog Control Signal A: 0-5 VDC Line Voltage B: 0-7 VDC 12: 48-140 Vrms C: 0-10 VDC 24: 180-280 Vrms D: 4-20 mA 48: 330-530 Vrms Series E: Internal Potentiometer PC 24 25 U C MC Rated Current Product Type 25: 25 Amps PC: Proportional Controller Required for valid part number 50: 50 Amps 90: 90 Amps OUTPUT SPECIFICATIONS (voltage) Description 120 A 240 A 480 A Operating Voltage (47-63Hz) [Vrms] 48-140 180-280 300-530 Transient Overvoltage [Vpk] 400 600 1200 Maximum Off-State Leakage Current @ Rated Voltage [mArms] 5 7 12 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/μsec] (2) 200 200 200 OUTPUT SPECIFICATIONS (current) Description 25 A 50 A 90 A Maximum Load Current (3) [Arms] 25 50 90 Minimum Load Current [mArms] 150 150 150 Maximum Surge Current (16.6ms) [Apk] 250 625 1200 Maximum On-State Voltage Drop @ Rated Current [Vpk] 1.6 1.6 1.6 Thermal Resistance Junction to Case (Rjc) [°C/W] 1.02 0.63 0.28 Maximum I² t for Fusing (8.3 msec) [A²sec] 260 1620 6000 FDE-07-01 REV. A Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Control Relays DataSheet (1) INPUT SPECIFICATIONS Description DC Control Control Voltage Range (VDC) 8-32 Input Current Range [mA] [P1] 28-30 Nominal Input Impedance [Ohms] [P3] 30K Control Must Operate Voltage "On"[VDC][P3] 5-32 Control Must Release Voltage "Off" [VDC][P3] 0-4 Control Input Current [mA][P3] 0-1.25 PLV Range Option A [VDC][P4] (2) 0.8-5 PLV Range Option B [VDC][P4] (2) 1-7 PLV Range Option C [VDC][P4] (2) 2-10 PLV Range Option D [VDC][P4] (2) 4-20 Nominal Input Impedance Option A,B,C[ohms][P4] 20K Nominal Input Impedance Option D [ohms][P4] 220 OUTPUT STATUS FUNCTIONS Conditions LED Initial Logic Supply On Flash Once Load Voltage Missing / Load Open (w/control disabled) Flash Once Intermittenly Load Voltage Missing / Load Open (w/control enabled) Flash Twice Intermittently Analog Input < Threshold Off Analog Input < Threshold < max Varying Brightness Analog Input > max On, Bright GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) 4000 VRMS 9 Minimum Insulation Resistance (@ 500 VDC) 10 Ohm Maximum Capacitance, Input/Output 10 pF Ambient Operating Temperature Range -20 to 80°C Ambient Storage Temperature Range -40 to 125 °C Weight (typical) 3.0 oz (86.5g) Encapsulation Thermally conductive Epoxy Terminals-Power Screws and Saddle Clamps Furnished, Unmounted Terminals-Control Barrier Strip Screw Terminals Recommended Terminal Screw Torque Range: 8-32 Screws -20 in. lbs.(Screws dry without grase) GENERAL NOTES (1) Voltages are reference to GND (Ground = 0 VDC) P2 (2) PLVI voltage can go up to max. supply voltage without damage Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Control Relays DataSheet MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] Analog Input OPTIONS: A, B, C, D Analog Input OPTIONS: E (Internal Potentiometer) MOUNTING 1.10 MOUNTING 1.10 HOLE/SLOT (27.9) HOLE/SLOT (27.9) 8-32 TERMINAL 8-32 TERMINAL 0.19 (4.9) DIA. .45 0.19 (4.9) DIA. .45 (2 PLACES) (2 PLACES) (11.4) (11.4) OUTPUT OUTPUT 1/L1 2/T1 1/L1 2/T1 2.31 2.31 [58.8] [58.8] 1.88 1.88 [47.8] [47.8] P4 OUTPUT OUTPUT P3 P3 STATUS STATUS P2 P2 P1 P1 .86 .86 BASE PLATE BASE PLATE (21.8) (21.8) 1.78 1.78 .125(3.2) .125(3.2) (45.3) (45.3) THERMAL DERATE INFORMATION 25A 50A 90A 90 30 95 60 120 .2˚C/W 1˚C/W 95 1˚C/W .5˚C/W 25 100 .5˚C/W .4˚C/W 2˚C/W 1.5˚C/W 100 80 20 40 100 3˚C/W 2˚C/W 1˚C/W 15 110 110 110 20 40 10 NO HEATSINK 120 5 120 120 NO HEATSINK 0 0 0 20 40 60 80 0 20 40 60 80 5 10 15 20 25 20 40 60 80 10 20 30 40 50 20 40 60 80 Load Current (Amps) Load Current (Amps) Load Current (Amps) Max Ambient Temp. (ºC) Max Ambient Temp. (ºC) Max Ambient Temp. (ºC) Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Power Dissipation Base Plate Temp (˚C) Power Dissipation Base Plate Temp (˚C) Power Dissipation Base Plate Temp (˚C) Control Relays DataSheet WIRING DIAGRAM (for Options A, B or C using an external potentiometer) Electrical Connections AC 10k to 50k pot for P4 Options A, B or C P1 P2 + Setpoint Adjust P4 OUTPUT 1/L1 2/T1 10K - 50K Enable For A,B or C Option DC OUTPUT GND STATUS Supply P1 + +Vdc P1 8-32Vdc (+) P2 Ground (-) Wiring for Option E P3 ON/OFF Control P4 0-5V, 0-7V, 0-10V, 4-20mA Enable OUTPUT STATUS FUNCTIONS Conditions LED DC GND Initial Logic Suppy On Flash Once Supply P1 Load Voltage Missing / Load Open (w/control disabled) Flash Once Intermittently +Vdc Load Voltage Missing / Load Open (w/control enabled) Flash Twice Intermittently Analog Input < Threshold Off Analog Input < Threshold < max Varying Brightness Analog Input > max On, Bright OUTPUT VS ANALOG INPUT SIGNAL CURVES 50/60Hz 50/60Hz 0-5Vdc Option A 0-7Vdc Option B 50/60Hz 0-10Vdc Option C 100 100 100 80 80 80 60 60 60 40 40 40 20 20 20 0 0 0 0.5 2 3 3.5 4 5 4.5 0 1 1.5 2.5 4.5 0 1 2 3 4 5 6 7 8 0 1 2 3 4 5 6 7 8 9 10 11 Input Voltage P4 Input Voltage P4 Input Voltage P4 50/60Hz 4-20mA Option B 100 80 60 40 20 0 3 5 7 9 11 13 15 17 19 21 Input Voltage P4 AGENCY APPROVALS, CONFORMANCES AND EMC Agency Approvals E116949 Rev. 072817 ECN 20288 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. True RMS Output Voltage as a Percentage of Line Voltage True RMS Output Voltage as a Percentage of Line Voltage True RMS Output Voltage as a Percentage of Line Voltage True RMS Output Voltage as a Percentage of Line Voltage Control Relays DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH. EXPLOSION. • Eteindre • 在操作此设 • Desconectar • Spenga tutta • Disconnect all • Stellen Sie toutes les todos los l'alimentazione 备之前请先 power before jeglichen sources suministros de che fornisce 关闭电源。 installing or Strom ab, der d'énergie de energia a este questa working with dieses Gerät cet appareil equipo antes apparecchiatura 若不遵守这些说明， this equipment. versorgt, bevor de trabajar avant de prima di lavorare 可能会导致严重的 Sie an dem con este equipo. travailler a questa • Verify all Gerät Arbeiten 人身伤害甚至死亡。 dessus de cet apparecchiatura connections • Verificar todas durchführen appareil and replace all las conexiones • Verificare tutti • Vor dem covers before y colocar todas i collegamenti • Vérifier tous Drehen auf turning on e sostituire las tapas antes connections, et Energie alle power. de energizer remettre tous tutte le coperture Anschlüsse prima el equipo. couverts en überprüfen Failure to follow dell’accensione olace avant de und alle these El mettre sous Abdeckungen instructions will L'omissione di incumplimiento ersetzen. De non-suivi de result in death queste istruzioni de estas ces instructions or serious injury. provocherà la Unterlassung instrucciones provoquera la morte o dieser puede provocar mort ou des lesioni serie Anweisungen la muerte o lésions sérieuses können zum lesiones serias. sérieuses. Tode oder zu schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISQUE DE DOMMAGE MATERIEL ET DE GEFAHR VON MATERIALSCHÄDEN UND RISK OF MATERIAL DAMAGE AND HOT SURCHAUFFE DU BOITIER GEHÄUSEERHITZUNG ENCLOSURE • Les panneaux latéraux du produit peuvent être • Die Seitenwände können heiß sein. Lassen Sie • The product's side panels may be hot, allow chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. the product to cool before touching. toucher. • Beachten Sie die Montageanweisungen, • Follow proper mounting instructions including • Respecter les consignes de montage, et • Führen Sie keine Flüssigkeiten oder torque values. notamment les couples de serrage. Fremdkörper in das Produkt ein. • Do not allow liquids or foreign objects to enter • Ne pas laisser pénétrer de liquide ni de corps this product. étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE RISCHIO DI DANNI MATERIALI E D'INVOLUCRO 材料损坏和高温外壳的危险性 SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Respetar las instrucciones de montaje, y en • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Control Relays DataSheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.