CRYDOM MP240D4

PCB Mount DataSheet AC DC MP Series • SIP SSR • Ratings to 4A @ 280 VAC or 3A @ 60 VDC • Triac (AC) or Transistor (DC) output • DC Control • Normally open (AC or DC) or normally closed output (DC only) • CE Compliant to EN60950-1 PRODUCT SELECTION Control Voltage 3 A 3 A 4 A 3 A 3-32 VDC MPDCD3 MP120D3 MP240D3 MP240D4 AVAILABLE OPTIONS Operational Voltage 120: 12-140 VAC Operational Current 240: 24-280 VAC 3: 3 Amps Series DC: 3-60 VDC 4: 4 Amps DC D 3 -B MP Output Function / Type Control Voltage Blank: Normally Open D: 3-32 VDC -B: Normally Closed (DC only) Required for valid part number For options only and not required for valid part number (1) AC OUTPUT SPECIFICATIONS Description MP120D3 MP240D3 MP240D4 Operating Voltage (47-63Hz) [Vrms] 12-140 24-280 24-280 Transient Overvoltage [Vpk] 400 600 600 Maximum Off-State Leakage Current @ Rated Voltage [mA] 5 5 5 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/μsec] (2) 200 200 200 3 3 4 Maximum Load Current [Arms] 0.02 Minimum Load Current [Arms] 0.02 0.02 Maximum Surge Current (16.6ms) [Apk] 90 90 130 1.6 1.6 1.6 Maximum On-State Voltage Drop @ Rated Current [Vpk] Maximum I² t for Fusing (50/60Hz, 1/2 cycle) [A² sec] 36 36 72 0.5 0.5 0.5 Minimum Power Factor (with Maximum Load) (1) DC OUTPUT SPECIFICATIONS Description MPDCD3 Operating Voltage (47-63Hz) [Vrms] 3-60 Maximum Load Current [Arms] 3 Minimum Load Current [mA] 0.02 Maximum Surge Current for 1 second [Adc] 5 Maximum On-State Voltage Drop @ Rated Current [Vpk] 1.5 1.0 Maximum Off-State Leakage Current @ Rated Voltage [mA] FDE-07-01 REV. A Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. LOAD LOAD CONTROL CIRCUIT LOAD LOAD PCB Mount DataSheet (1) INPUT SPECIFICATIONS Description AC Output DC Output DC Output (-B) Control Voltage Range [VDC] 3-32 3-32 3-32 Must Turn On Voltage [VDC] 3.0 3.0 1.0 Must Turn Off Voltage [VDC] 1.0 1.0 3.0 Typical Input Current @ 32VDC [mA] 23 23 23 1500 Nominal Input Impedance [Ohm] 1500 1500 1/2 Cycle 0.1 0.1 Maximum Turn-On Time [msec] Maximum Turn-Off Time [msec] 1/2 Cycle 0.1 0.1 GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output (50/60Hz) 4000 Vrms 9 Minimum Insulation Resistance (@ 500 V DC) 10 Ohms Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -40ºC to 80ºC Ambient Storage Temperature Range -40ºC to 125ºC Weight (typical) 0.7 oz. (20g) Encapsulation Thermally Conductive Epoxy Enclosure and PCB Meets the requirements of IEC60335-1 GENERAL NOTES 1) All parameters at 25°C unless otherwise specified. 2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 3) Inductive loads should be diode suppressed WIRING DIAGRAM TRIGGER CIRCUIT + + 3 2 1 4 3 2 1 4 -DC +DC -DC +DC B A (3) B A AC AC Load can be wired in location A or B -DC +DC Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. PCB Mount DataSheet THERMAL DERATE INFORMATION MP240D4 MP120D3 MP240D3 MPDCD3 MPDCD3-B 4.0 3.0 2.0 1.0 0 20 40 60 80 Ambient Temperature (ºC) MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] BOTTOM VIEW 1 draft top to base 1.00 0.25 (25.4) (.64) LOAD CONTROL .25 TYP. (6.35) 1 2 3 4 0.20 .015 .70 (5.1) (4.1) (17.8) .40 1.10 (10.2) .040 (1.0) DIA. (27.9) 1.70 (4 PLACES) (43.1) AGENCY APPROVALS Agency Approvals Designed in accordance with the requirements of IEC 62314 LR 81689 REG.-Nr. 5900 E116950 (120D3,240D3 and 240D4 Only) Rev. 081017 ECN 20296 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. Load Current (Amps) PCB Mount DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH. EXPLOSION. • Eteindre • Spenga tutta • 在操作此设 • Desconectar • Disconnect all • Stellen Sie toutes les l'alimentazione todos los 备之前请先 power before jeglichen sources che fornisce suministros de 关闭电源。 Strom ab, der installing or d'énergie de questa energia a este working with dieses Gerät cet appareil apparecchiatura equipo antes 若不遵守这些说明， this equipment. versorgt, bevor avant de prima di lavorare de trabajar 可能会导致严重的 Sie an dem travailler a questa con este equipo. • Verify all Gerät Arbeiten 人身伤害甚至死亡。 dessus de cet apparecchiatura connections • Verificar todas durchführen appareil and replace all las conexiones • Verificare tutti • Vor dem covers before y colocar todas • Vérifier tous i collegamenti Drehen auf turning on las tapas antes e sostituire connections, et Energie alle power. de energizer tutte le coperture remettre tous Anschlüsse el equipo. prima couverts en überprüfen Failure to follow dell’accensione olace avant de und alle these El mettre sous Abdeckungen instructions will L'omissione di incumplimiento ersetzen. De non-suivi de queste istruzioni result in death de estas ces instructions provocherà la or serious injury. Unterlassung instrucciones provoquera la morte o dieser puede provocar mort ou des lesioni serie Anweisungen la muerte o lésions sérieuses können zum lesiones serias. sérieuses. Tode oder zu schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISQUE DE DOMMAGE MATERIEL ET DE GEFAHR VON MATERIALSCHÄDEN UND RISK OF MATERIAL DAMAGE AND HOT SURCHAUFFE DU BOITIER GEHÄUSEERHITZUNG ENCLOSURE • Les panneaux latéraux du produit peuvent être • Die Seitenwände können heiß sein. Lassen Sie • The product's side panels may be hot, allow chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. the product to cool before touching. toucher. • Beachten Sie die Montageanweisungen, • Follow proper mounting instructions including • Respecter les consignes de montage, et • Führen Sie keine Flüssigkeiten oder torque values. notamment les couples de serrage. Fremdkörper in das Produkt ein. • Do not allow liquids or foreign objects to enter • Ne pas laisser pénétrer de liquide ni de corps this product. étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE 材料损坏和高温外壳的危险性 RISCHIO DI DANNI MATERIALI E D'INVOLUCRO SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Respetar las instrucciones de montaje, y en • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice. PCB Mount DataSheet ANNEX - ENVIRONMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.