EBM-PAPST INC. G1G170-AB31-51

G1G170-AB31-51 EC centrifugal fan backward curved, single inlet with housing (flange), Gas blower for gas-condensing heating ebm-papst Landshut GmbH Hofmark-Aich-Str. 25 · D-84030 Landshut Phone+49 871 707-0 Fax+49 871 707-465 info3@de.ebmpapst.com www.ebmpapst.com Nominal data Type G1G170-AB31-51 Motor M1G074-CF Phase 1~ Nominal voltage VAC 230 Frequency Hz 50/60 Type of data definition ml -1 Speed min 6530 Power input W 410 Current draw A 1.8 Min. back pressure Pa 2000 Min. ambient temperature °C - 25 Max. ambient temperature °C +55 Min. temp. of flow medium °C -25 Max. temp. of flow medium °C +80 ml = max. load · me = max. efficiency · rfa = running at free air · cs = customer specs · cu = customer unit Subject to alterations Item no.: 50129-5-9980 · Revision: 66688 · Print-out 07/11/2011 · K. Boruzki (VI-I) · Page 1 of 5 ebm-papst Landshut GmbH · Hofmark-Aich-Str. 25 · D-84030 Landshut · Phone +49 871 707-0·Fax +49 871 707-465 · info3@de.ebmpapst.com · www.ebmpapst.com G1G170-AB31-51 EC centrifugal fan backward curved, single inlet with housing (flange), Gas blower for gas-condensing heating Technical features Mass 4.7 kg Size 170 mm Surface of rotor Coated in black Material of protective cover Polyflam RPP 374-ND CS1 (UL 97-V0) Material of impeller Aluminium sheet Housing material Die-cast aluminium Direction of rotation Clockwise, seen on rotor Type of protection IP 20 Insulation class "B" Max. permissible ambient +80 °C motor temp. (transp./ storage) Min. permissible ambient -40 °C motor temp. (transp./storage) Mounting position Any Cooling bore / aperture Rotor-side Motor bearing Ball bearing Technical features - Tach output - Motor current limit - PFC, active - PWM control input - Over-temperature protected motor EMC interference immunity Acc. to EN 61000-6-2 EMC interference emission Acc. to EN 61000-6-4 (industrial environment) EMC harmonics Acc. to EN 61000-3-2/3 Leakage current <= 3.5 mA Electrical leads With plug Motor protection Thermal overload protector (TOP) wired internally Product conforming to CE standard Approval CSA C22.2 Nr.113; UL 507 Item no.: 50129-5-9980 · Revision: 66688 · Print-out 07/11/2011 · K. Boruzki (VI-I) · Page 2 of 5 ebm-papst Landshut GmbH · Hofmark-Aich-Str. 25 · D-84030 Landshut · Phone +49 871 707-0·Fax +49 871 707-465 · info3@de.ebmpapst.com · www.ebmpapst.com G1G170-AB31-51 EC centrifugal fan backward curved, single inlet with housing (flange), Gas blower for gas-condensing heating Product drawing 1 Housing side parts sealed with NBR round cord (pentane-resistant) 2 3-pole strip; mating connector (not included in delivery): tyco No. 350 766-1; female connector: No. 926 884-1 2.1 L 2.2 N 2.3 PE 3 5-pole strip; mating connector (not included in delivery) Molex No. 39-01-4050, female connector Molex No. 39-00-0059 3.1 (+) 3.2 Speed monitoring 3.3 Not assigned 3.4 PWM input 3.5 ( - ) 4 Bleeder connection for pressure relief possible Z View Z Item no.: 50129-5-9980 · Revision: 66688 · Print-out 07/11/2011 · K. Boruzki (VI-I) · Page 3 of 5 ebm-papst Landshut GmbH · Hofmark-Aich-Str. 25 · D-84030 Landshut · Phone +49 871 707-0·Fax +49 871 707-465 · info3@de.ebmpapst.com · www.ebmpapst.com G1G170-AB31-51 EC centrifugal fan backward curved, single inlet with housing (flange), Gas blower for gas-condensing heating Connection screen No. Pin Signal Function / assignment ST1 1, 2, 3 L, N, PE Power supply 230 VAC, 50-60 Hz, neutral conductor, protective earth ST2 1 UB External voltage 24-45 VDC ST2 2 DUE Speed monitoring output connection, monitoring circuit output, 3 pulses per revolution, current source 1 mA ST2 3 N.C Not assigned ST2 4 PWM PWM - 2 - 6 kHz control input, PWM on n = 100%, PWM low n = 0% ST2 5 GND GND - Connection for control interface Item no.: 50129-5-9980 · Revision: 66688 · Print-out 07/11/2011 · K. Boruzki (VI-I) · Page 4 of 5 ebm-papst Landshut GmbH · Hofmark-Aich-Str. 25 · D-84030 Landshut · Phone +49 871 707-0·Fax +49 871 707-465 · info3@de.ebmpapst.com · www.ebmpapst.com p sf [Pa] G1G170-AB31-51 EC centrifugal fan backward curved, single inlet with housing (flange), Gas blower for gas-condensing heating Charts: Air flow 50 Hz Druck psf [Pa]für Rho=1,2kg/m^3 qv[cfm] 0 50 100 150 200 250 300 350 400 450 4.000 16 15,5 3.800 15 14,5 3.600 14 Measurement: LU-56469 3.400 13,5 4 Air performance measured as per ISO 5801 13 3.200 Installation category A. For detailed 12,5 information on the measuring set-up, please 3.000 12 contact ebm-papst. Suction-side noise levels: LwA measured as per ISO 13347 / 3 11,5 2.800 LpA measured with 1m distance to fan axis. 11 The values given are valid under the 10,5 measuring conditions mentioned above and 2.600 may vary according to the actual installation 10 2 situation. With any deviation from the 2.400 9,5 standard set-up, the specific values have to be checked and reviewed with the unit 9 2.200 installed. 8,5 1 2.000 8 7,5 1.800 7 6,5 1.600 6 1.400 5,5 5 1.200 4,5 1.000 4 3,5 800 3 2,5 600 2 400 1,5 1 200 0,5 0 0 0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 qv[m^3/h] Measured values U f n P I qv p e sf -1 3 V Hz min W A m /h Pa 1 230 50 6530 410 1.80 380 2000 2 230 50 6665 400 1.75 330 2400 3 230 50 6915 370 1.62 250 2800 4 230 50 7250 326 1.44 150 3200 Item no.: 50129-5-9980 · Revision: 66688 · Print-out 07/11/2011 · K. Boruzki (VI-I) · Page 5 of 5 ebm-papst Landshut GmbH · Hofmark-Aich-Str. 25 · D-84030 Landshut · Phone +49 871 707-0·Fax +49 871 707-465 · info3@de.ebmpapst.com · www.ebmpapst.com p sf [Pa] psf_E[IN H2O]