1.6X0.8mm INFRARED EMITTING DIODE Part Number: AP1608F3C Features Description z 1.6mmX0.8mm SMT LED, 1.1mm thickness. F3 Made with Gallium Arsenide Infrared Emitting diodes. z Mechanically and spectrally matched to the phototran- sistor. z Package: 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD1356 REV NO: V.8 DATE: JUN/07/2011 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.H.Wu ERP: 1203000007 Selection Guide Po (mW/sr) [2] Viewing @ 20mA Angle [1] Part No. Dice Lens Type Min. Typ. 2θ1/2 AP1608F3C F3 (GaAs) Water Clear 1.2 3 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity/ luminous flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Parameter P/N Symbol Typ. Max. Units Test Conditions Forward Voltage [1] F3 VF 1.2 1.6 V IF=20mA Reverse Current F3 IR 10 uA VR = 5V Capacitance F3 C 90 pF VF=0V;f=1MHz Peak Spectral Wavelength F3 λP 940 nm IF=20mA Spectral Bandwidth F3 Δλ1/2 50 nm IF=20mA Note: 1. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Symbol F3 Units Power dissipation PD 80 mW F 50 mA DC Forward Current I Peak Forward Current [1] iFS 1.2 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 °C Storage Temperature TSTG -40 To +85 °C Note: 1. 1/100 Duty Cycle, 10μs Pulse Width. SPEC NO: DSAD1356 REV NO: V.8 DATE: JUN/07/2011 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.H.Wu ERP: 1203000007 AP1608F3C SPEC NO: DSAD1356 REV NO: V.8 DATE: JUN/07/2011 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.H.Wu ERP: 1203000007 AP1608F3C Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) SPEC NO: DSAD1356 REV NO: V.8 DATE: JUN/07/2011 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.H.Wu ERP: 1203000007 PACKING & LABEL SPECIFICATIONS AP1608F3C SPEC NO: DSAD1356 REV NO: V.8 DATE: JUN/07/2011 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.H.Wu ERP: 1203000007